1967 Ford Mustang

Bare metal power steering hose bracket for any 1967-69 small block Mercury Cougar or Ford Mustang. 289-2V, 289-4V, 302-2V, 302-4V, 351-2V, and 351-4V. No rubber insulator included.

For any 1967 or 1968 Cougar with either a 289 or 302 engine. Virtually the same bracket as for the 1969 351W engine. Except for the obvious 1-1/4 inch hole in the middle of the bracket, they are the same. Compare the OEM used part price to the reproduction part. Ford master part number C7AZ-3C511-A, same part number as the 351W bracket with the addition of the large hole. Ford intended to have a casting number stamped on these brackets and it would have been C7AA-3C511-B. For restoration...

Perfect fit for use with AC or non-AC 67, 68, 69, or 70 Cougar with the 390, 427, or 428 big block.

For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part. For restoration purposes, this bracket was factory painted satin black.

This cast bracket bolts to the frame on the driver side and anchors the power steering hydraulic cylinder. One of the benefits of buying parts from Western parts cars is that they have not been corroded by salt! This part comes "as taken from a parts car". At least two variations of this bracket (see photos above) between 1967-70. Our observations show the version with the curved casting number version orientation to be from 1970 Cougars with were all built in Dearborn, Michigan. The...

Used bracket for mounting the rear axle flexible brake hose. This is a factory welded in bracket that was removed from a 1967-69 Mercury Cougar or Ford Mustang. Double check your placement for your particular year, when welding the bracket to your car. Good used bracket the you need to separate from the factory spot welds. Part bead blasted for photo, has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Ford part number C7ZZ-2A051-A.

Used trunk plate or bracket for mounting the "J" bolt for the spare tire. Several versions of this bracket, this is the most common one. Mounts flat to the trunk floor surface on all 1967-70 Mercury Cougar hard tops, with full sized spare tires. Additionally, 1971-73 Mercury Cougar convertibles. We cut these out of the trunk floors, so there will be some metal preparation for the customer. Ford part number C7AZ-6247076-A.

Used trunk plate or bracket for mounting the "J" bolt for the spare tire. Several versions of this bracket. Mounts on a corner of the trunk floor surface. 1969-70 Mercury Cougar convertibles, with full sized spare tires. Additionally, 1971-73 Mercury Cougar hard tops. This folded bracket was also used with cars with space saver spare tires, or trunk mounted batteries. We cut these out of the trunk floors, so there will be some metal preparation for the customer. Ford part...

Upper and lower bracket set assembly. One year only 1967 Mercury Cougar or Ford Mustang bracket, used on both fixed and tilt column cars. Basic Ford part number for upper bracket is 3676, lower bracket number 3668.

Lower steering column mounting bracket. 1967-68 Mercury Cougar and Ford Mustang. Right and left halves as shown. Rubber gasket sold separately. Ford part number C7ZZ-65017A50 and C7ZZ-65017A51.

Reproduction concours correct throttle return spring bracket for the Mercury Cougar or Ford Mustang equipped with the 390GT engine. This bracket is shorter in length than the 390-4V piece.Ford part number C7OZ-9741-B.Also good for 1968-1/2 - 428CJ.

Upper bracket, one year only 1967 Mercury Cougar or Ford Mustang bracket, used on both fixed and tilt column cars. Basic Ford part number for upper bracket is 3506. Upper bracket only, subject to availability. *Note - The upper bracket is about 5-1/8" inches long, Hole spacing is 4-3/16ish". There is an early Mustang / Falcon bracket looks right, but is only 4-1/4" inches long, don't be fooled.