All Available Parts - 1967 Ford Mustang

Used timing chain cover with casting number C3AE-6059-A, for any 1967 390 engine. 1967 Mercury Cougar and 1967 Ford Mustang. Cast aluminum construction without excessive damage. Installation bolt kits also avialable.Replaces Ford part number C3AE-6059-A.*Note there is a different version of this timing cover for 1968-70 390/428CJ engines.

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a brass plunger. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to retain your mounting bracket...

Used heater and air conditioning box for early to mid 1967 Mercury Cougar and Ford Mustangs. These are getting so hard to find without a broken drain cock or rust in the metal lips. We have a few single halves if you need the half without the drain cock. Soon we will have every single internal and external part from this assembly listed here, in the mean time give us a ring for those obscure parts! The unit you see pictured is typical of what you can expect in a 1967-68 with just a minor...

Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what...

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit is an exact fit!Replaces part # C7ZZ-19988-A.

Original two piece assembly that bolts to the passenger side of your firewall on A/C equipped Cougar's. Comes as taken from parts car. If you own a 1969 Cougar you will need to look at the configuration of the evaporator lines. During the 1969 model year this grommet bracket changed to reflect the running year change. It will look like the 1970 pictured bracket.Ford part # C7ZA-19B589-A.

Reproduction disc brake distribution block for Mercury Cougar or Ford Mustang with factory installed disc brakes. Mounts to the driver side fender apron with a single bolt. Bare block without single pin brake switch.  Replaces Ford part # C7ZZ-2B257-D. Check out this video

All new disc brake pads are supplied to us by brand name manufacturers. Boxed set of four pads. Semi-Metallic linings. Kelsey Hayes Brake caliper system.

These retainers are designed to keep the disc brake pad inside the caliper on 1967 Cougars.

Excellent USA made quality replacement disc brake rotor. One piece rotor with wheel studs as shown, also includes installed bearing race. Replaces Ford Part #: C5ZZ-1102-B.

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2" and is a very good copy of the original. Made in America.

New premium reproduction tear drop power disc brake master cylinder for the Mercury Cougar or Ford Mustang equipped with factory power disc brakes in front and drums in back. Has proper threaded line size for OEM or replacement brake lines, 3/8-24 and 1/2-20. The main difference between this unit and our economy version is cosmetics, as this premium unit comes with the correct "tear drop" casting; other difference to consider are this unit has a 1" bore, instead of 1 1/8"...

Used passenger side (right hand) Kelsey Hayes two piston disc brake caliper as factory installed on 1967 Cougar, Mustang, and Fairlane. 1967 was unique in that it had a 7/16" inlet fitting as where earlier Mustang calipers used a 3/8" inlet fitting. Thunderbird and full sized Ford cars used a larger version of this caliper. Tough parts to find in rebuildable condition. Ford part # C7OZ-2B120-C.

This A/C vacuum canister mounts to the passenger side fender well and controls doors inside the A/C unit. This unit includes a built in check valve. Fits 1968-1970 Mercury Cougar and Ford Mustang. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength.  Replaces Ford part # C8ZZ-19A566.

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...

Redesigned modern evaporator has 35% MORE PASSES, using three-circuits, instead of the original single-circuit design. This is a direct bolt-in replacement and requires no modification.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal. It has been our experience that these often fail within a few years. We suggest flushing and pressure...

New heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Replaces part # C7ZZ-18591-B.

Used heater blower motor for very late 1967 and all 1968 Mercury Cougars and Ford Mustangs with integral or factory air conditioning. The tell tale sign is the early motors have a nipple of attaching the rubber elbow. This later version has a round hole for attaching a different rubber elbow. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting...

Used air conditioning thermostat switch for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Ranco for Ford. Ford part numbers C7ZA-19618-C or C7ZZ-19618-A.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors, for 1967-68 the color was brown. This is the basic valve with a single vacuum port.

Shaft or rod for air inlet damper door for any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-A.

Shaft or rod for the evaporator damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft has a tab mounted on the lever, and is clocked differently than the 1969-73 version. The evaporator damper door allows air to pass over the evaporator in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related...

Shaft or rod for the heater damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-B.*Note will not work in 1969-73 A/C boxes.

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1969-70 brackets, but this one has a slightly shorter and pointed stud. Replaces Ford part number C7ZZ-18A456-A.

Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.

Shaft or rod for the A/C damper blower door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft is clocked differently than the 1969-73 version. This air conditioning damper door is in front of the blower or fan in the center of the car. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number...

Used rubber elbow that vents air to the blower motor on most 1967 Mercury Cougar and Ford Mustangs with factory air conditioning. At some point in time, this elbow design changed. Easy to tell, this early style connects to a nipple on the fan blower motor. The later version has a hole in the motor case. Not needed with reproduction fan motors, they don't even have the hole. Replaces Ford part number C7ZA-19A786-A.

Used rubber elbow that vents air to the blower motor on most 1967 Mercury Cougar and Ford Mustangs with factory air conditioning. At some point in time, this elbow design changed. Easy to tell, this early style connects to a nipple on the fan blower motor. The later version has a hole in the motor case. Not needed with new production fan motors, they don't even have the hole. Replaces Ford part number C7ZA-19A786-B.

Used heater blower motor for 1967 Mercury Cougars and Ford Mustangs with integral or factory air conditioning. The tell tale sign is the early motors have a nipple of attaching the rubber elbow. Later version has a round hole for attaching a different rubber elbow. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is also included. On...

Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...

Air conditioning fan blower assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Grade B A/C vacuum canister that has a non working check valve. Suitable for filling the hole in your passenger side fender apron. This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and not holding vacuum, tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's...

Used mounting bracket from a 1967-68 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

Premium reproduction rubber grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Molded rubber exactly like the original! Other reproductions on the market are die cut from sponge rubber sheets and nothing like the original. * Note - Used starting during the early part of 1969. Compare the evaporator line orientation for both years. ...

Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. There are a couple of versions of this housing. There is a version with a cooling nipple for cooling the...

Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version. There are a couple of versions of this housing. There is a version with a...

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. Blue is the color found 1969 and 1970 and early 1971. Blue and Brown actuators are exactly the same. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port...

Used extension or rod for the vacuum actuator for controlling dampers and levers on the 1967-68 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 1-15/16 inches long. For 1967-68 Cougar and Mustang, all three vacuum actuators used this same length extension. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C7ZA-18A318-A....

Used heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Ford part # C7ZZ-18591-B.

Unique to power brakes and only with 1967 Cougar steering columns. Pedal shipped bare, picture may show hardware and pedal pad with trim. *Note* You will have to drill holes in your existing pedal hanger to accommodate the power brake pedal. Since systems with a vacuum booster take less effort to activate than systems without, a different folcrum point is used that does not utilize built in bushings into the hanger. Please refer to our power brake pedal hanger listing for measurements on where...

This pedal comes naked as shown, we highly suggest buying a used original as it will come with correct mounting hardware.  Replaces Ford part # C7ZZ-2455-K.

Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. SEM brand COLOR COAT paint is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not recommend this product for driver side arm rests, door pull straps, shift...

Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

Used vacuum tank or canister for the early built 1967 Mercury Cougar and Ford Mustang with factory or integral air conditioning. According to the Ford Master Parts Catalog, the cutoff date for this A/C canister was December 1967. Later cars used the common two nipple vacuum cans that mount inside the passenger side fender below the hood hinge on the passenger side.Replaces Ford part number C7ZZ-19A566-A.

Usually ships in 3-5 business days. Reproduction heater box with A/C for 67 - 68 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). See related products. The style of this box most resembles the 1967 version, with the flat mating surfaces between the two...

Air inlet damper door for any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1969-73 door, but without a small notch. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...

Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...

Heater Box Assembly for 1967-1968 Mustangs without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a factory type fiberglass two piece heater box/heater core casing. The heater box is a pre-assembled unit which includes the gasket and all seals. The heater plenum attaches to this assembly and directs warm air to the car. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts...

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.

These reproduction pieces are factory correct replacements for your 1967-68 Cougar or Mustang and will only fit non A/C heater cores of those years.

Used Heater Box Assembly for 1967-1968 Mercury Cougar and 1965-68 Ford Mustang without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a used factory fiberglass two piece heater box/heater core casing. We suggest purchasing the foam kit and new heater core. These used boxes are over 45 years old, there will likely be some cosmetic issues, which include minor cracks or chipped fiberglass. Clips to hold two pieces together are included. *Note...

Metal fan wheel or squirrel cage for any 1967-68 Mercury Cougar or Ford Mustang with heater only. Dimensions 4-1/4 inches in diameter and 2-1/2 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.

Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.

Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1967-68 Mercury Cougar and 1965-68 Ford Mustang.Ford part # C2OA-18591-A or C8ZZ-18591-A*Note - Excludes Heater with integral or factory air conditioning.

Used mounting plate for the heater blower motor on the 67 - 68 Cougar or Mustang without A/C.

Reproduction heater cable set for your beloved Cat or Pony. This set is an exact fit! Replaces Ford part # C7ZZ-18518-A. *Customer Feedback*     "My first deal with Don was clear back in the 1980's and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you...

For us with Cougars without factory AC. The originals were made of cardboard and are very prone to failure from moisture. These are made from virgin ABS black plastic and are excellent quality in every respect. Not often does a reproduction come along that blows away OEM, but this definitely is that part. Before you finish making your online order with us, go look at your plenum to see what condition your original is in. Replaces Ford part #: C5ZZ-18471-A

Mounts to the rear of the factory installed heater control ventilation control panel on 1967 Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1967 selector button kit. Click this LINK for shinny new button awesomeness!Ford part # C7ZZ-18578-A.

Mounts to the rear of the factory installed heater control ventilation control panel on 1967 Mercury Cougar and Ford Mustang. Switch and wiring pigtail with plug.Replaces part # C7ZZ-18578-A.

Not for use on cars with A/C. Keep in mind we also have excellent used knobs sold individually or as a set.

These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing.Ford part # C7ZZ-6501891.

Good reproductions but we suggest you consider our good used original FORD units that have been closely inspected and have had new plastic rollers installed. *NOTE* Originals were painted semi gloss black. Often the regulator is fine and all you need is new rollers. Check out this helpful youtube video on how to replace these rollers.

Good reproductions but we suggest you consider our good used original FORD units that have been closely inspected and have had new plastic rollers installed for half the price! *NOTE* Originals were painted semi gloss black.Often the regulator is fine and all you need is new rollers. Check out this helpful youtube video on how to replace these rollers.

Good used original FORD part that has been closely inspected for rust on the roller shaft / stud and bent arms. 1967 & 1968 units will have new rollers included. We are of the opinion that these are better quality than the off shore reproductions that are available. With a little elbow grease this good quality originals will have years of good service left in them. Unlike the reproductions these come with a one year warranty.Ford Part Numbers:C5ZZ-6530306-A, C5ZZ-6530307-A, C8ZZ-6530306-A,...

Used driver side (left hand) grade "A" clear vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.This vent window glass often comes with a frame and...

Used grade "A" clear passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # C5ZZ-6521412-C. *NOTE* Air...

22954 Door vent window pivot bracket

22992 "D" shaped top washer, Ford called it a 'stop'. See assembly picture. 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side, sold individually.

22992 SPRING Tension spring for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

34392-S7 5/16 inch nut for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

375897-S White plastic 5/16" washer for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 2 per side, sold individually.

C2AZ-22963-A Special steel flat washer with flat sides for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

Used grade B stainless steel vent window glass frame for the right side or passenger side door on a 1967 Mercury Cougar or Ford Mustang. Similar frame as the 1968

Used grade B stainless steel vent window glass frame for the left side or driver side door on a 1967 Mercury Cougar or Ford Mustang. Similar frame as the 1968

Used driver side (left hand) vent window frame as it comes out of thedoor. This unit is just the bare window frame and will need some cleaning as itis 40 plus years old. A great option for those of you who have a limited budget. Also, because this is an original piece, it will have a far superior fit and function than the"off shore" reproductions that are currently offered.Ford part # C7ZZ-6522205-A.*Note* "B" grade will have some pitting in the chrome on theinterior side of the frame. Check...

Mounts to the door jamb and keeps water from going into the quarter panel. Sold as a pair. Replaces Ford part #: C7ZZ-6528182 and C7ZZ-6528183

Reproduction driver side (left hand) clear door vent glass for the Mercury Cougar or Ford Mustang. There are three versions of this piece of glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version is not a tint option that...

Reproduction green tinted driver side (left hand) vent window glass for the Mercury Cougar or Ford Mustang. If your car has factory integral air conditioning, it came with green tinted glass that was called "Sun-X" tint. This is an excellent replacement piece and is just a the bare piece of glass.  This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few...

Used grade "A" passenger side (right hand) vent window frame as it comes out of the door and is just the bare window frame. This is not a perfect part but it will look good on a low mile car that shows a little patina. The weatherstrip track that continues down into the door can be had with this part for no extra charge, please mention it in the comments section when you order online. Ford part # C7ZZ-6522204-A. Casting # C7ZB-6522222-ACheck out our video below for helpful tips on...

Reproduction Passenger side (right hand) clear door vent glass for the Mercury Cougar or Ford Mustang. There are three versions of this piece of glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version is not a tint option...

Reproduction pair of vent / wing window handles for the Mercury Cougar or Ford Mustang.

Good used driver side (left hand) quarter window guide for the Mercury Cougar or Ford Mustang. Grade B will have some rust or erosion from moisture, missing zinc plating. This unit will have all three window stops and both window guides still attached. Riveted window stops have part number of C4ZB-6529838-A. Ford part # C7ZZ-6529753-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our...

Good used passenger side (right hand) quarter window guide for the Mercury Cougar or Ford Mustang. Grade B will have some rust or erosion from moisture, missing zinc plating. This unit will have all three window stops and both window guides still attached. Riveted window stops have part number of C4ZB-6529838-A. Ford part # C7ZZ-6529752-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our...

C5ZZ-6529968-A two of these window stop brackets mount to each of the quarter window frames. Bracket for all 1967-68 Mercury Cougars and 1965-68 Ford Mustangs. Works on either the passenger or drivers side. Casting # is C4ZB-65298A22-ASold individually

Used driver side (left hand) grade "A" green tinted vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars or Mustangs came with this SUN-X tinted glass if they were factory equipped with A/C. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part #...

Used grade "A" tinted passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars and Mustangs came with this green tinted SUN-X glass if they were also equipped with A/C from the factory. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than...

Good used original FORD part that has been closely inspected for rust on the roller shaft / stud and bent arms. 1967 & 1968 units will have new rollers included. We are of the opinion that these are better quality than the off shore reproductions that are available. With a little elbow grease this good quality originals will have years of good service left in them. Unlike the reproductions these, come with a one year warranty. Ford Part Numbers: C5ZZ-6530306-A, C5ZZ-6530307-A,...

Used roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Also found on all 1967-68 Mercury Cougar and Ford Mustang door window channels. Often times one of the rollers breaks off and allows chattering of the window movement. Sold individually: 3 total rollers on each side of the quarter window brackets. 2 like this

Used single plastic roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Note that there is only one of this style of roller on each quarter window. This is a simple white plastic roller and a rivet. Note that there are 2 rollers with 2 pieces of round white plastic. Often times one of the rollers breaks off and allows chattering of the window movement. Included is a good roller and drilled out rivet. These can be reused if you drill out the...

Used bracket for mounting the bottom of the quarter window guide to the car body. Fits all 1967-68 Mercury Cougar and 1966-68 Ford Mustang coupe and convertible (non fastback). "L" shaped bracket that designed for mounting and adjusting the rear quarter window.Replaces Ford part number C6ZB-6529778.

Passenger side quarter window slide. This is the 10 1/2" slide that bolts to the inner body of the quarter window area.

Driver side quarter window slide. This is the 10 1/2" slide that bolts to the inner body of the quarter window area.

Reproduction of the very hard to find window roller for the window channel / quarter window frame on the 67 - 68 Cougar and Mustang. Doubles as both the single and double type roller (with the included support washer).Included in this kit are: One roller, one rivet, one wavy washer, one flat washer, and one support washer, measures exactly 1" wide. Rivet is for a 1/4" hole.2 required per door glass channel, 3 per quarter window frame.Sold individually. Replaces Ford Part # C8SZ-57262A32-A....