1967 Ford Mustang

This is a used distributor for the 1967 Mercury Cougar or Ford Mustang equipped with the 390 4V engine. It was also used on the 1968 Mercury Cougar GT-E equipped with the 427 4V engine.Application is 1967 automatic with smog, and 1968 automatic with Thermactor smog system. Check out this video

New Old Stock vacuum advance. This style used 1965-67 on Autolite V-8 distributors. Designed for use with a threaded nipple. DD-190 and code 303 numbers associated with this unit. This is an Autolite marked vacuum advance, there are other service replacement units marked MOTORCRAFT. Threaded nipple available separately. Ford Part Number C5AZ-12370-A

Silicone and fasteners, everything needed for installation of our seat divider panel.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

This listing is for the outer doors pieces only, Cougar and Mustang are identical. These original NOS FoMoCo parts fit better and will last longer than repro. Ford part numbers C7ZZ-6521453-A and C7ZZ-6521452-A

C7ZZ-652221-B Restored, stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Driver side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind.*Note - Excludes Mustang fastback and convertible. Check out this video

C7ZZ-652220-B Restored, stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Passenger side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible. Check out this video

C5ZZ-6522600-C

New old stock driver side door handle the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. This handle is NOS, NOS doesn't always mean high quality plating. Includes mounting hardware and pads. Round button not included. Replaces Ford Part #: C4DZ-6222405-A

New old stock passenger side door handle the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. This handle is NOS, NOS doesn't always mean high quality plating. Includes mounting hardware and pads. Round button not included. Replaces Ford Part #: C4DZ-6222404-A

1967 Cougars used this cast iron hinge that weighs a pound or more over the 1968 stamped steel version. You may want to opt for a 1968 hinge if your goal is to lighten your car. You will shed about six pounds if you replace all four with a set of 1968 stamped steel Mercury Cougar door hinges. These used hinges usually need new pins and bushings, for the small cost of the new parts we suggest you purchase the Complete Hinge Rebuild Kit. Check out this video ...

Kit replaces one side. Contains all necessary parts including pins, bushings, a new cam plate, spring, and roller to rebuild both upper and lower hinges. This kit is for the cast iron type hinges found on the 1967 and early 1968 Cougar.Replaces Ford Part #: C5ZZ-6522800-K.