1968 Mercury Cougar

Driver side (left hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. Will fit Convertible if upward facing rocker flange is modified. *NOTE* This floor pan has the outside lip bent down which is...

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. Will fit Convertible if upward facing rocker flange is modified. *NOTE* This floor pan has the outside lip bent down which...

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This surround or "U" plate was originally attached with heat to pin connectors. To reattach we suggest using glue. This U part attaches to the bottom of the console shifter bezel and shrouds the light. Check out this video

New Old Stock, NOS rear reflector gasket. This pad goes between the rear quarter panel and quarter panel reflector on the 1968 Mercury Cougar only.  Replaces Ford part #: C8WY-13493 or C8WY-13A493-A. *Note - These were not installed on Ford Mustangs, but they could be installed since they use the same reflector after Feb 15, 1968.

Restored Zinc Plated side marker light / turn signal backing plate. Right is the same as left, two brackets required per car, sold individually.

Very nice pit free mirror worthy of a low mile original car. *NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere! Hole spacing: 4 3/8" Ford part # C7WY-17696-A Do you have riv-nut questions? Here are riv-nut answers! ...

This driver quality manual adjust driver side mirror shows wear and the chrome will not polish out. *NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere! Hole spacing: 4 3/8" Ford part # C7WY-17696-A Do you have riv-nut questions? Here are riv-nut answers! Cougar Applications:1967 Mercury Cougar1968 Mercury Cougar ...

NOS unpackaged driver side manual adjust mirror. Shows some shelf wear, a small scuff on the base and a smudge on the glass. Don't forget to select a mounting gasket and mounting kit if needed. Casting number reads C7WB-17743-B Ford part # C7WY-17696-A. *NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere! Hole spacing: 4 3/8" Do you have riv-nut questions? Here are riv-nut answers! ...

Grade A mirror will have no cracks, deep scratches or pits. Will look right at home on a low mile garage kept car.

Working driver side (left hand) grade "B" remote mirror with dull chrome. Don't have too high of expectation on this, it is 40 years old and comes from a car we most likely pulled from a brier patch...

Fine scratches but great for the guy who wants original. The Reproduction does not have the II-DMI-6 lettering at the bottom like this original. You will have to carefully peel (roll back) the aluminum backing that is glued in place before gluing it in your mirror. If you use needle nose pliers and take your time it usually works fine. Note that the pictures of our 67-68 mirrors and lens can be deceiving. This is a tapered mirror, the narrow end faces upward on a Cougar, it is reversed when...

We do not currently have any used units in stock, but we often place items like this on our site for documentation purposes. We hope to have a reproduction of this item soon. Do you have riv-nut questions? Here are riv-nut answers!