All Available Parts - 1968 Mercury Cougar

If your Cougar came from a region that uses road salt your buckets are probably rusted in the corners or worse. Our dry "West Coast" buckets are 100% rust free and the mounting tabs are not broken from the removal of stubborn bolts. They will not be bent or damaged in any way. Keep in mind we do have grade B brackets for much less that only have minor bends or blems that could be easily corrected. *NOTE* These parts are far more important than most people realize. If they structural integrity...

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

Driver side hidden headlamp hinge. This part affixes to the backside of the headlamp cover and acts as a hinge. The design was changed 12-15-67 so you will have to know the date in which your grille was built. All 1967 model year Cougars were built prior to 12-15-67 but we mention this here as many 1967 Cougars have had 1968 replacement parts installed over the years. The brass bushings have been inspected for wear, no collision damage and no rust. Both adjustment bolts are included with the...

Passenger side headlight door.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the passenger side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four...

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. NOTE - If your actuators are the type with the internal spring (Thunderbird actuators had a failsafe internal spring) we cannot accept those as cores. An easy way to tell which actuators are the...

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. ALL GRADE B ACTUATORS COME WITH A 60 DAY WARRANTY. You can find the seal rebuild kit here. Used grade "B" headlight door actuator for your Mercury Cougar. Every once in a while (not often) we will...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16-A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

This conversion will replace the old, tired, vacuum system that likes to leak and wear out. This kit consists of two electric actuator assemblies (new Mazda Miata motor) with a plug and play wiring loom for easy installation. Simply remove all existing vacuum components and replace with this kit to have headlight covers that work under any conditions with the car running or not. These new motors are smoother and more reliable than previous versions that utilized the Ford Probe motors and are...

New black screws for attaching the headlight doors to all 1967-68 Mercury Cougars. Four screws needed per side for a total of 8 per car. We have found 3 different styles of separate screws that were used during the 1967-68 model run, San Jose and Dearborn may have accounted for a difference. This one matches exactly to one of the more common ones that were installed. Replaces Ford Part number 376352-S15.

Used passenger side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 4 screws and grind down 16 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Replaces Ford...

Used driver side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 4 screws and grind down 16 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Replaces Ford part...

Used passenger side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 2 screws and grind down 2 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Small section with two...

Used driver side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 2 screws and grind down 2 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Small section with two...

This bolt is what adjusts your headlamp cover height. Rare find to still have an original rubber bumper in place that is not compressed or cracked. Four required per car, sold individually. Check out this video

Used, hood latch assembly that is in good working order. This unit will have a bit of metal shifting on the brace portion. Can be straightened fairly easily We also have many grade "A" latches. We also have the individual components listed. Check out this video ...

Used hood release latch by itself, this is a component of the hood latch assembly for any 1967-68 Mercury Cougar.

Used Grade A - Hood latch brace, brace only, fits all 1967-68 Mercury Cougars. Straight piece, this is typically the only part of the hood latch assembly that gets damaged in a collision. This is Grade A used, we also have Grade B braces that need some massaging to be perfect.Ford part number C7WY-16747-A.

Used Grade B - Hood latch brace, brace only, fits all 1967-68 Mercury Cougars. Grade B brace that will need some massaging to be perfect. These are fairly easy to get straight enough cosmetically. We also sell complete assemblies and Grade A used braces.Ford part number C7WY-16747-A.

Used support bracket for the hood latch on any 1967-68 Mercury Cougar. L shaped support bracket goes on top of the hood latch assembly. It also attaches to the radiator core support.Ford part number C7WY-16707-A.

This reproduction spring puts tension on the headlight adjusting ring so when you turn the screw on the adjusters the ring remains tight and will move as adjusted. Sold individually, four required per car. These small springs were used in 1967-68, a larger spring was used in 1969 through 1973.

Reproduction gasket for the vintage two piece Carter fuel pump bowl for the Mercury Cougar or Ford Mustang equipped with either the 390-4V, 427-4V or 428CJ engine.

Reproduction fuel filler neck from a 1967-68 Mercury Cougar. Correct for use with factory or reproduction 16 gallon fuel tanks. 

Used grade "B" clear rear window glass for the Mercury Cougar coupe. This unit has multiple fine scratches and water spots and is good for driver or something to "just plug the hole." It is almost impossible to remove even fine scratches from tempered glass.

Quality reproduction CLEAR rear window glass that unfortunately does not have original "Carlite" markings or date code. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original.

Good used windshield washer pump rubber hose assembly

Pair of reproduction headlight actuators for the 67 - 68 Mercury Cougar. Manufactured to meet and exceed factory specs without the need for additional parts or modification. Keep in mind when you buy these units WCCC will pay $50 for the pair of your rebuildable core units. Our video below explains how to determine if your cores are acceptable. Check out this video on how to rebuild your existing headlight vacuum actuators ...

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable.  NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS.   *NOTE* These...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable. NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS. *NOTE* These parts are far more...

Driver side headlight door. New Old Stock.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The...

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. Kit includes used check valve and fittings shown, but does not include headlight switch. "I found a good way to...

Replacement plastic vacuum tee for use on the 1968 Mercury Cougar headlight vacuum hoses. OEM Ford style replacement. Original Ford part number 373845-S.

This bracket attaches the vacuum storage tank for your headlights to the core support inside the driver fender. It differs from the 1967 bracket in that an oval hole was put in it to allow the socket and pigtail assembly for the side marker light to pass through the bracket located closest to the fender. 1969 uses the exact same bracket except for a slightly different clip design. Sold individually, two required per car. Cougar part number C8WY-13B008-A.

Includes all the hardware needed to mount your 1968 vacuum storage can located inside the driver fender. Parts do not come cleaned as shown, we clean many of these used parts so as to show the details and true condition of the part you can expect to receive.

Quality "STANDARD" brand reproduction switch for your vacuum actuated hideaway headlights. This switch fits multiple years and makes which means multiple dash configurations. You will need to "break off" your unique extension and attach it to this unit. The extension (spacer) can be removed easily by placing your old switch in a vise and using a wedge shaped chisel to break the tiny spot welds. When reattaching, most any glue such as Gorilla glue, JB weld or even silicone will work as you are...

Good used part with no pitting or obvious damage. Includes stamped steel metal mounting bracket attached to the backside. Headlamp hinge C8WY-13A155-A. Ford part # C8WY-13A137-B. *NOTE* For use on 1968 Cougars built after 12/15/1967. Not for use with 1968 Cougar GT-E. Check out this video ...

Good used eyelid with no pitting or obvious damage. Includes emblem and metal mounting plate. For use with headlamp hinge part # C8WY-13A154-A. Ford part # C8WY-13A136-B. *NOTE* For use on 1968 Cougars built after 12/15/1967. Not for use with 1968 Cougar GT-E. Check out this video ...

Passenger side hidden headlamp hinge. This part affixes to the backside of the headlamp cover and acts as a hinge. The brass bushings have been inspected for wear, no collision damage and no rust. If you try to use a hinge from a 1967 built prior to 12-15-67 it will not fit on your 1968 Cougar. Ford part number C8WY-13A154-A. Check out this video ...

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

Reproduction grille mounting kit for the driver (left hand) and passenger (right hand) sides of the Mercury Cougar.

Reproduction rubber hose connector as used on the 1968 headlight hoses. A pair of these connectors connects the color coded hoses that lead to the headlamps from the short hoses coming out of the firewall from the headlight switch. Replaces Ford part # C8WY-13A170-B

Used grade "A" driver side (left hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and found to be free of large cracks, has good chrome with no pits or major scratches and is not severely warped. Hairline cracks will be present in the area of the painted...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used driver side hidden headlamp hinge. This part affixes to the backside of the headlamp cover and acts as a hinge. The brass bushings have been inspected for wear, no collision damage and no rust. If you try to use a hinge from a 1967 built prior to 12-15-67 it will not fit on your 1968 Cougar. Ford part number C8WY-13A155-A. Check out this video ...

Used grade "B" passenger side (right hand) grill section for the Mercury Cougar. 1968 is unique from the 1967 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. This 1968 piece has a more durable reinforced casting in this area. This grille half has been carefully inspected and may have some minor cracking, but will have good chrome with no pits, major scratches, and is not severely warped. It will have a misalignment issue as...

Used grade "B" driver side (left hand) grill section for the Mercury Cougar. 1968 is unique from the 1967 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and may have some minor cracking, but will have good chrome with no pits, major scratches, and is not severely warped. It will have a misalignment issue as they all do in the...

Used 1968 Mercury Cougar GT-E horizontal grille bar, from the driver side headlight door. Measures 15-3/16 inches long. This is the longest section of extruded aluminum from an original car. There are a total of 7 pieces for a complete grille on a GT-E. It can be cut down to fit any other position that you may be missing. This is a rare find. This one has road tested, meaning that it does have some minor scuffs from use.

Used 1968 Mercury Cougar GT-E horizontal grille bar clip or keeper for the center grille section. This is a rare find, limited to stock on hand.

Replacement plastic vacuum tee for use on the 1968 Mercury Cougar headlight vacuum hoses. OEM Ford style replacement. Dimensions: 3/16 x 3/16 x 1/4

Used to store your shoulder belt above the windlace on the drivers side (harder to find than passenger side). These are often rusty, missing or broken. I am not aware of any reproductions being made.

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Contrary to what you might think at first glance, the support rods used in 1967 - 1968 Cougar headliners are not the same front to back. Each of the rods is bowed to a different curve. To replace a headliner and make it look right, you must keep the rods in the same order as they came out of the original headliner. To help you do this, Lincoln-Mercury coded each rod with a color applied to each end. From front to rear, the 1967 - 1968 color codes of the headliner rods are: None (this is the...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Great for those wishing to shed a few pounds from their early Cougar as this insulation weighs less than one pound and the original weighed almost four pounds. If you want to keep your Cougar original then you will want to check out our used package tray sound deadener / insulation / jute. *NOTE* This is actually patterned for a 1968 Cougar, but will work in a 1967.

These fasteners were used to keep your package tray in place. In 1967 - 1968 two T shaped fasteners were held in place with a spring clip. Sold individually. Ford part number C4AB-6246698-A

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.

Reproduction AQUA Sunroof Headliner for the 1967 and 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of installing...

Reproduction BLACK Sunroof Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...

Reproduction DARK IVY GOLD / DARK GREEN Sunroof Headliner for the 1967 and 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured)....

Reproduction LIGHT BLUE Sunroof Headliner for the 1967 and 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. This is a VERY light blue used on the early 1967 XR7 with dark blue interior. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and...

Reproduction MEDIUM BLUE Sunroof Headliner for the 1967 and 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...

Reproduction PARCHMENT / OFF-WHITE Sunroof Headliner for the 1967 and 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking...

Note: This is the correct color for a Parchment / Off-White interior in a Cougar. Reproduction PARCHMENT / OFF-WHITE Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not...

Reproduction MEDIUM BLUE Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...

Reproduction LIGHT AQUA Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...

Reproduction BLACK Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of installing...

Rear bracket assembly for mounting the 1967-68 Mercury Cougar overhead consoles. Bracket spans the roof section of the car, felt covered padding on the roof side. Comes with both small end brackets and clips. Main bracket has a Ford part number of C7WB-65519B24 and the two smaller brackets have a part number of C7WB-65519B38. *NOTE* Will not work for installing the long Mustang overhead consoles.

Reproduction DARK AQUA Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...

Reproduction MAROON / DARK RED Interior Headliner for the 1967 or 1968 XR7 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red and Dark Ivy Gold. Thinking of installing your own headliner? Join in the discussion...

NOS part that shows shelf wear and may need to be repainted in places. Can easily be made to fit 1968. Ford part number C7WY-13A137-B Casting number C7WB-13A139 *NOTE* For use on 1968 Cougars built after 12/15/1967. Not for use with 1968 Cougar GT-E. Check out this video ...

1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples.Also sold in a set of 8. ...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1967-70 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. These are mostly going to have the C8AB part numbers on them, which is what we have the most of. Included is cups...

Set of 8 1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples. Also sold individually.

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Reproduction interior headliner in light ivy gold / light green for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured)....

Reproduction overhead console bracket for the Mercury Cougar or Ford Mustang. This is a decent part, but not as good as the original FoMoCo part we offer.

This good used original front bracket for the over head console of the Mercury Cougar and Ford Mustang. This unit is better than the repro and was also used on 1967-68 Mustang fastback. We also have the clips that attach to the overhead console and then clip into this bracket. Ford Part #: C7ZZ-65519B46-A. *NOTE* 2 are required per car.

Reproduction pillar post mouldings that feature and vinyl overlay for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

Reproduction light blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

Grade A condition - driver side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1968 Mercury Cougar, driver side only. Found on XR7 and most Standard model Cougars. Grade A condition, will have supple vinyl without damage. minor or no de-lamination. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best results you should...

Grade B condition - driver side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1968 Mercury Cougar, driver side only. Found on XR7 and most Standard model Cougars. Grade B condition, will some foam de-lamination on the back. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best results you should plan on spraying...

Nice reproduction headliner trim for 1968 Mercury Cougar standard models without padded windshield pillars. Also fits several years of Mustang. They come black, but can be painted to match your interior. Right and left steel pillar trim with mounting screws. Ford part # C5ZZ-6552136 and C5ZZ-6552137.

Reproduction dark ivy gold / dark green headliner for the 1967 and 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Thinking of installing your own headliner? Join in the discussion here for some helpful tips. Check out our video below showing how to install...

Reproduction saddle headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Grade B condition - passenger side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1968 Mercury Cougar, passenger side only. Found on XR7 and most Standard model Cougars. Grade B condition, will some foam de-lamination on the back. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best results you should plan on...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

Used grade "B" over head or roof console pad for any 1967-68 Mercury Cougar XR7. All of these pads will have some distortion or foam separation as shown in the photos. These came in a variety of colors, so be sure and include your desired color in the comments section of your online order. Plan on using vinyl paint for improving the color, due to time, and UV light. Color vinyl pad only, other parts available and sold separately.Replaces Ford part number C7WY-65519A92 or C8WY-65519A92. ...

Reproduction pair of package tray retainers for your 67 - 70 Cougar or Mustang. Made from stamped steel with a black finish to keep them from rusting. They install in the front of the package tray, keeping it secure.

Used Grade "A" over-head or roof console pad for any 1967-68 Mercury Cougar XR7. All of these pads will have minimal to no distortion or foam separation as shown in the photos. These came in a variety of colors, so be sure and include your desired color in the comments section of your online order. Other parts available and sold separately.Replaces Ford part number C7WY-65519A92 or C8WY-65519A92.