Other Ford/Mercury

Air conditioning belt tensioning pulley for Ford Thunderbird and other full sized 1968 and 1969 Ford, Lincoln, and Mercury cars with the 429. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click here to view the repair bearing (ITEM #: 11-0413), we've got what you need! Ford part # C8VA-8A619-B Check out this video ...

NOS New Old Stock air conditioning fixed idler pulley for all 1967 Mercury Cougar and Ford and Mustang, all with 390 engines. Ford part number C7SZ-8678-B.

Air conditioning fixed idler pulley for Ford or Mercury with the 352 / 390 / 410 / 428 engines. These are all sold with new bearings. If your pulley only needs a bearing? Click this BEARING link, we've got what you need! Ford part # C5AA-8A919-C and C5AZ-8678-C Check out this video

Used bracket and pulley assembly with new installed bearing for Mercury and Ford equipped with the 429CJ, 429, and 460 engine. This assembly was also equipped on the 1970 - 1971 Torino, Ranchero, and Cyclone with the 429CJ engine. Also many other 429 / 460 engines. Listed in the Ford Master Parts Catalog (MPC) as D0AZ-8678-B. \ *Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for...

C3AE-9425-B Cast iron intake manifold used on all 1963 390-4V engines in a Mercury or Ford. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C3AE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Fits FE engines, this could have come from a Galaxie or Thunderbird or full sized Mercury. Probably also 352 engines. Current date available: 2M29. December 29, 1962. *Trivia - One of the heaviest car...

Lightly used intake manifold cast aluminum 427-4V medium riser. Blue Thunder casting 427MR-4V. Has the oil fill tube in front, dual plane, and the road draft provision in the back. Very tall manifold, likely to not fit under the stock hood of a Cougar or Mustang. Do your research on this, if you know, you know. We don't. Small portion on the driver side front has been lightly ground down, likely for a coil. No other issues noted. 

C7AE-9425-F Cast aluminum intake manifold used on all 1968 W code 427-4V engines in a Mercury Cougar GT-E or 1968 Ford Mustang Shelby GT-500 (non KR models). Stock 4 barrel intake manifold. Take off manifold with correct casting number of C7AE-9425-F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-H. *TRIVIA* This is also known as the PI aluminum intake manifold, PI = Police Interceptor. ...

Cast aluminum Sidewinder intake manifold. Over the counter speed part for the 427 Medium Riser. The offset carburetor placement was to help provided equal length runners in regards to flow. Single 4 barrel intake manifold as shown. Looking closely at the photos, this one has had a repair performed in the past. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford casting number C6AE-9424-J.

Used FoMoCo aluminum intake manifold for Ford FE engines. The single plane carburetor mounting bases, indicate that this was designed for Ford Thunderbird with 390 engines. Stepped bases were for Ford Galaxie. FoMoCo marked, with a 1D20 casting date i.e. April 20, 1961. There has been some repair done to the area of the water neck, and at least one of the threaded holes is buggered up. No linkage, carburetors, nor fuel logs included. Fits all Ford FE engines 360, 390, 406, 427, 428. ...

Reproduction 15x7" Eliminator wheel with a silver center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This silver 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need...

Rebuildable Core grade lower control arm for any 1970 Mercury Cougar and Ford Mustang. These are wearable items, and we list this item for those folks who really wish to go 'Concours trailered'. These interchange from side to side, two per car. One year only design, has a unique washer for the sway bar end links. Fits other 1970 Ford cars such as Torino and Cyclone. Even though these are select parts, we recommend that the ball joints and bushings be replaced. Limited to stock on...

Plastic Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good! Replaces Ford Part # D0OZ-1130-F.