All Available Parts - 1967 Mercury Cougar

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use.

Uncommon jack as identified by the coarse threads. This version was made by a specific supplier AUSCO or Auto Specialties Manufacturing Company. AUSCO supplied jacks to Ford until 1970.See the link for the Ford jack research done by Marcus Anghel - Anghel Restorations

New manufactured Tremec T-5z World Class Transmission. Same transmission as installed in Fox Body Mustangs. This is the common transmission for conversions that does not involve extensive modifications to 1967-73 Mercury Cougar or Ford Mustang. Small block Ford V-8 engines only, 289 / 302 / 351W and 351C. Brand new transmission, no core required. 1 year warranty, with recommended synthetic ATF. Flush and fill after first 500 miles, 30,000 miles there after. Bare transmission as shown, no...

Reproduction Front end rebuild kit specifically for the 1967 Cougar with articulated strut rod arms. There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to...

Used clip for mounting the vacuum modulator steel line or tube on 1967-68 Mercury Cougar or Ford Mustang with C4 or automatic transmission. Mounts under one of the top bolts where the bell housing connects to the engine block. This is not a reproduced part, that we know of.  The basic Ford part number is 7C072.

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

This is a the economy version of our lower control arm assembly, with a spot welded on reinforcing plate. We are sorry, but we just cannot recommend this part. The Scott Drake premium version of this lower control arm is superior and costs less. In the picture, you can tell that it is lacking a rolled lip on the outer edge that the originals and the Drake Premium reproduction offers. This is a non-returnable item. Having issues with wobbly or loose steering? Check out our video on sloppy...

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...

Reproduction machined tube seat set, for ram cylinder and control valve on early 1967 Mercury Cougar and Ford Mustang with the 1/4" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that starting in mid to late 1967, the control valves had 5/16" fittings all the way to 1970.

Used AQUA passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer plastic...

Quality reproduction. Fits all 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Lin, Hey, just wanted to thank you for your prompt service. Last Friday 4/24/09 I ordered a 71 - 73 Idler Arm and today (Monday 4/27/2009) I received it. WOW!!! I just wanted to let you know that you guys are...

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  ...

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory power steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a yellow paint mark on...

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a pink...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

This product has received the 'Crappy Product' certificate. Items that receive the 'Crappy Product' certificate are products that we carry for comparison purposes as they are often the version offered by other vendors or because it is the only version available. We would not be willing to use these parts on our own cars, and we do not recommend purchasing these parts. WE ARE NOT ABLE TO ACCEPT RETURNS FOR THESE PARTS. Economy replacement vinyl top that looks great and fits perfect. This...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

C7ZA-3590-A Early 1967 Steering box pitman arm with 1 inch sector shaft. Manual steering only, used with SMB-C and SMB-E steering boxes. Ford part number C7ZZ-3590-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below.

Pressure die cast, with quality chrome sun visor center bracket and rear view mirror mount. Replaces one of the most visible interior parts on a 1967 Mustang or Cougar. Break away style, two piece construction. Beware of cheap single piece imitations that are available as they are unsafe. Keep in mind you will have to give your screw driver some good pressure when installing to make the mirror fit tight. Replaces Ford part # C7ZZ-17690-A.These are manufactured in the USA. ...

Used driver side outer bucket seat SADDLE hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561695.

Used IVY GOLD passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer...

Used passenger side outer bucket seat IVY GOLD hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561694.

Used SADDLE passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer plastic...

Good used original insulation pad as taken from a Western parts car. Used Jute pad that will not have any water or pest damage. These original pads are nice because they are made from a much more dense material (3.74 pounds) than the reproductions (.75 Pounds) and they have the factory perforated "knock out" sections for the optional speakers. A "Must Have" for show cars as the rear package tray fits better with this low profile material and no modern insulation resembles the original when...

Used passenger side outer bucket seat red hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561694.

Used passenger side outer bucket seat black hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561694.

Used driver side outer bucket seat black hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561695.

This dealer option was installed for people who were not comfortable with the height of their seats. This same kit was used on many intermediate Ford Products from 1965-1970. One kit does one bucket seat or one bench seat. Ford part # C6OZ-6362016-A. Click on images to enlarge. The screw on clips were included in the kit so the spacer would stay in place as the seat was guided into the four holes in the seat riser. Often these clips are cracked or missing and we cannot guarantee all four will...

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

Reproduction white headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Contrary to what you might think at first glance, the support rods used in 1967 - 1968 Cougar headliners are not the same front to back. Each of the rods is bowed to a different curve. To replace a headliner and make it look right, you must keep the rods in the same order as they came out of the original headliner. To help you do this, Lincoln-Mercury coded each rod with a color applied to each end. From front to rear, the 1967 - 1968 color codes of the headliner rods are: None Red White Brown...

NOS or new old stock - C7SZ-13A165-A Bolt like pin that one or both sides of the hidden headlight hinge rides on. 1967-68 Mercury Cougar uses 4, 1969-70 Mercury Cougar uses 2 on the outsides. Also used on many other 1967-71 Ford, Mercury, and Lincoln cars with the vacuum operated hidden headlights. 1967 - 1970 Mercury Cougar and XR7 1967 - 1969 Ford Thunderbird or T-Bird 1968 - 1969 Ford and Mercury full sized cars 1971 Ford and Mercury full sized cars 1970 and newer Lincoln Continental...

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. ALL GRADE B ACTUATORS COME WITH A 60 DAY WARRANTY. You can find the seal rebuild kit here. Used grade "B" headlight door actuator for your Mercury Cougar. Every once in a while (not often) we will...

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. "I found a good way to remove 50 years of crud. Soak the lines in hot water and dawn dish soap for a bit then take a...

Pair of used wire anchors for keeping the rear most headliner bow stationary. These are fragile wires, and prone to rusting. We try to keep them in inventory. 1967-68 anchor wires are 5-9/16 inches long. A DIY person can improvise these pretty easy, using lengths of regular wire. Ford part # C4OB-6252180.

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang that feature two 2" gauge pods on the driver side. Sold as a pair.

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

This single port version was used in the latter part of 1967 and all of 1968. Keep in mind we have units that are not as clean looking but still hold vacuum for about half the price. Cougar part number C7WY-13A185-C headlamp vacuum reservoir.

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. If you have a tried and true method of cleaning these hoses let us know and if it sounds good we will post it here!NOTE:...

Used spacer for the lower windshield moulding

Good used rear window with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available as each piece differs. Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded...

New replacement gas tank filler cap for all 1967-69 Mercury Cougars and 1970 Cougars without California emissions. This is a vented fuel cap.

Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.

This is what is referred to as a campaign part. It was found that the early 1967 Cougars were having some issues with the headlights and this revised hose kit with ground strap was the fix. Often these have been found opened on dealers shelves with the "near new" take off hoses placed back in the original box. This is a great find for the guy wanting to do a concours restoration on his 1967 Mercury Cougar. Not for use on a 1968 as the switch was located under the dash as opposed to next to the...

This is a good used fitting with large and small nipples for use with the foot actuated washer pumps found on 1967-68 Mercury Cougar and Ford Mustang. Good used part that we verify the check valve is working. These screw into of the rubber covered pumps.

Used vented fuel, or gas cap as installed on 1967-69 Mercury Cougar and 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap. This version does have a check valve, one way vented. This is probably a service replacement fuel cap. Typically, OEM factory caps only said "VENTED", see our related item for that specific gas cap.We stock these in limited quantities, and will have an intact paper gasket. "ANTI SURGE"...

Good used rear window with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available as each piece differs. Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded...

Premium reproduction fuel / gas tank for the Mercury Cougar or Ford Mustang. 16 gallon capacity, correct in every way including the drain cock.Replaces Ford part # C5ZZ-9002. Check out our video on replacing the fuel system on a '68 Cougar! ...

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...

Reproduction fuel pump for all 1967-70 Mercury Cougars and Ford Mustangs equipped with the 289, 302 or 351W engines. Be aware that this pump has a 3/8 inch fitting for the fuel line.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

Reproduction intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang

All of our used insulation hood pads are guaranteed to be filthy dirty, less than perfect (as shown) and include at least one spider. We cannot fold these to ship them and they are too large for UPS. You must pick them up in person or we can ship them for free when you purchase a hood from us.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has one pressed in brass fittings for vacuum hose, and one threaded port with added vacuum fitting as shown. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1968-69 vacuum advance, the later...

New Old Stock lower distributor bushing for most V-8 engines 1965 through 1968-69. Ford deemed this bushing as not needed during 1968. That is why all 351W distributors do not have one installed. All 289 distributors 1965-67 should have one installed, starting in 1968 some did, some did not. Many 1968-69 302-2V's and all Boss 302 distributors had them installed. Same with FE distributors all had them starting in 1965, by 1968-69, they were disappearing. Limited to stock on hand. If Ford deemed...

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970.  Ford part # C9AZ-9H576-A.

C7AE-9425-J Cast iron intake manifold used on 1967 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold, used after 9-11-1967. Take off manifold with correct casting number of C7AE-9425-J. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-N. *Trivia - One of the heaviest car intake manifolds ever made, over 80 lbs.

Good used, working vacuum advance, comes with the hard to find threaded vacuum nipple. This style used 1965-67 on Autolite V-8 distributors. Designed for use with a threaded nipple. DD-190 and code 303.Threaded nipple available separately. Ford Part Number C5AZ-12370-A

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory A code 289-4V V-8 engine. Rated at 225 Hp with 9.8:1 compression ratio in 1967. Not standard bore engine block, that may or may not have been in running condition when pulled. May or may not have 9.8:1 pistons. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex...

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Used Distributor / 289-4V / Automatic Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7ZF-12127-G  

Used Distributor / 289-4V / for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7ZF-12127-H

Used Distributor / 390-4V / Manual Transmission for the 1967 Mercury Cougar / 1967 Ford Mustang. Current distributor dated 7A19, January 19, 1967. Ford part number C7OF-12127-H  

Used Distributor / 390-4V / Automatic Transmission for the 1967 Mercury Cougar / 1967 Ford MustangCurrent distributor dated 7C29, or March 29, 1967. Ford part number C7AF-12127-U  

This is a used distributor for the 1967 Mercury Cougar or Ford Mustang equipped with the 390 4V engine. It was also used on the 1968 Mercury Cougar GT-E equipped with the 427 4V engine.Application is 1967 automatic with smog, and 1968 automatic with Thermactor smog system.

Used Distributor / 289-4V / Automatic Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7ZF-12127-B  

Used Distributor / 289-4V / Manual Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7ZF-12127-C  

Used Distributor / 289-4V / Automatic Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7ZF-12127-D  

Used Distributor / 289-2V / Automatic Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7OF-12127-E  

Used Distributor / 289-2V / Automatic Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7AF-12127-AH  

Used Distributor / 289-4V / for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7ZF-12127-A  

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 5L18, November 18, 1965.  Used 0.030 over bore 4.180" Ford 428 engine block. Bare block, no crank shaft. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight...

Used Distributor / 289-2V / Automatic Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7AF-12127-AE  

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 289 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6AE, C8AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 6K4 or October 4, 1966.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7L1, November 1, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 8B1, February 1, 1968.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

Reproduction ignition switch w/ cylinder and 2 keys for the 1967 Cougar or Mustang.NOTE: The item comes with economy keys, they are much thinner than the premium Ford keys. The cylinder will not accept the premium keys. Here is a helpful "How To" youtube video on how to replace your ignition switch.

NOS 1967-68 Mercury Cougar XR7 speedometer with trip meter. Original unused speedometer in FoMoCo box, all numbers at zero.  Ford part number C7WY-17255-C

Featured in this kit are all the basic items you need to convert your small block 1967 - 1968 Cougar or Mustang from a 20" wide radiator with a fixed four blade fan to a 24" wide radiator with 3 cores and the MAXIMUM cooling big block, high performance 7 blade clutch fan. This setup was used on the highest horsepower drive-trains of the day including the Legendary 427 Side-Oiler equipped GTE and the 428 SCJ Drag-Pak equipped Cougars and Mustangs. This might sound like overkill for your small...

Used on the ignition lock cylinder. This unit locates and maintains the angle to the dash from behind. Attaches with one small screw, and the bezel and retainer nut secures the whole works to the dash from the front. 1967-68 Mercury Cougar and Ford Mustang.

This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

Used clock for the center console equipped Mercury Cougar XR7. Most used clocks typically do not work after 40+ years and you can also expect that the lens will have some cracks. However, we offer a nice reproduction lens or restored clocks with a modern quartz movement or NOS movement.Ford part # C7WY-15000-B.Check out the video below on our new gauge tester: This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we...

C7WY-15000-A 1967 - 1968 Standard Cougar body code 65A or 65C, found optionally in the small center pod of the instrument cluster. Used clocks generally do not work after 40 years. These are considered cores. We also offer clocks with modern quartz movements or NOS movements in restored clocks. Check out the videos below on our new gauge tester and the "Cougar Dash Surgery Clock and Speaker Install by Andrew Chenovick: ...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

We shatter the castings from used back-up light assemblies to remove the socket and pigtail complete. This is for the person who has a nice original back up light and is willing to invest the time to repair a damaged pigtail. This light was also used on the 1965-1966 Ford Mustang.

We really cannot justify the average guy buying these over our quality reproduction pair. Only the most tedious of restorations would benefit from having this levels of detail. Sold as a pair, Ford part #: C5ZZ-13206-B for the passenger side and C5ZZ-13207-B for the driver side.

Ford sold service replacement taillights as a complete unit that included the backing, chrome and lens, just the lens or just the chrome. This listing is for one complete taillight unit as shown.Sold individually, two required per car. Ford part number C7WB-13440-A *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...