All Available Parts - 1969 Ford Mustang

New lower windshield moulding retainer screw. The retainers slide into the lower stainless steel windshield moulding and attach with these screws into the cowl top. #8 x 1/2 inch hex washer head screw with 1/4 inch drive. Several suppliers or styles of screws were used

Original FoMoCo used windshield wiper motor mounting bracket for your 1969-70 Mercury Cougar or Ford Mustang. This used bracket comes with grommets, for all 1969-70 Cougar and Mustangs. Mounts under the cowl cover at the windshield. Ford part # C9ZZ-17496-A.

New to the market grille fix for 1967 - 1968 Mercury Cougars / Patent Pending. These simple little grille repair clips have been needed since these cars were new! Over the years we have seen a multitude of home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will be listing all the different FoMoCo applications these clips will work on. These clips are sold as a set of four. NOTE: We've found that removing the legs from one side...

Reproduction headlamp adjusting nut and screw. Slightly longer screw than stock, small amount of added length does not interfere with anything in or behind the grille. The nut is an exact copy of what is found on the 1969-70 adjustment. Almost the same as the nut found on the 1967-68 Cougar, this isn't even shown on those grilles. 1967-68 mounts on the backside of the headlight bucket. Total of 8 adjustment screws used on each 1967-70 Cougar, item sold individually.Note: When installing...

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

Powder Coated. Replaces Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # C9ZZ-13076-A, tagged C9ZB-13076-B.*NOTE* A pair of these units were also used on the 1969 Mustang and Mach 1. However, they were not used on the quad headlight 1970 Mustangs.

Reproduction Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang.If you're working on both sides of your grille, you will need two kits, one kit will do one half of the grille.

Reproduction Headlamp Housing Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Reproduction interior windshield / A pillar post mouldings / trim that features a vinyl overlay and 2 inch gauge pods on the driver side (left hand) so you can add any gauges of your choice to your Mercury Cougar or Ford Mustang. These units are sold in pairs.

Interior windshield / A pillar post mouldings / trim for 69 - 70 Cougars and Mustangs that feature two 2" gauge pods on the driver side. Sold as a pair.  These are not the best fit but will work, notice it requires exterior screws to mount them. No returns.

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.

Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions only come in 'paint to suit' black but we have most original colors in used. Replaces Ford Part #: C9AZ-6204132.

Used single hole front mount center visor bracket for the 1969 / 1970 Mercury Cougar and Ford Mustang hard tops.  The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your desired color in the 'comments' section of your order. Ford part # C9AZ-6204132, casting # C9AB-6204132-B.

Reproduction moulding for 'upper windshield garnish' for any 1970 Mercury Cougar or 1969-70 Ford Mustang. This item not for 1969 Cougar hardtops or for convertibles. Item comes in black as shown, paint to match non-black interiors. This is a made in Taiwan part, and we recommend our used header mouldings. Ford part # C9ZZ-6503606-A.

Used moulding for 'upper windshield garnish' for any 1970 Mercury Cougar or 1969-70 Ford Mustang. This item not for 1969 Cougar hardtops or for convertibles. Item comes in black as shown, paint to match non-black interiors. Ford part # C9ZZ-6503606-A.

Reproduction saddle headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

New manufactured stainless steel fuel / gas tank for 1969 Mercury Cougar and 1969 Ford Mustang, 20 gallon capacity, has drain plug. Replaces Ford part #C9ZZ-9002. *NOTE* Tank will fit into all 1967-68 cars, fuel filler necks must be adjusted to fit with this taller tank. Sending units ideally should be changed to the 1969 sending units. 1970 cars with California emissions will have to change filler necks entirely.

Reproduction green tinted windshield that features a blue tinted band a crossed the top of the windshield. Not only will this unit look great, it will fit perfectly as well. Planning on installing the glass yourself? We also sell the glass to window channel weld. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed....

Best replacement for the original wiper blade assembly. Replaces Ford part #: D4AZ-17528 and C9AZ-17528-A. Sold individually

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4567S. This is the early style with "CAR bure TER" and Canada, has the 3/8" fuel nipple. Correct for 1968 Mercury Cougar with H or M code 351 engines and 1969 Ford and Mustang with 351W V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible...

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4385S. This is the style with "CARTER" and USA, has the 3/8" fuel nipple. Correct for 1968-69 Mercury Cougar with X or S code 390 engines and 1968-69 Ford and Mustang with 390 V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible dates, we will...

Reproduction aqua headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction dark blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.

For the purists out there we have a very limited amount of used visors that have no impressions, seam separation and minimal rust on the clips if any. Convertible and Coupe are the same.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually

Sold as pair on exchange or outright. Only cores with minimal corrosion can be considered for exchange. Ford part number C7AZ-6204144-A, casting number as seen on the backside reads C8AB-6204122-B.  Does not include smaller rod for the sun visor tips.  Sold as a pair.

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these.  Sold Individually Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

This kit contains 500 hog rings, more than enough for two bucket seats and one bench seat.

These hinge covers are exact copies of the originals. These are neutral in color so you can paint them to match your interior color.

Correct texture, good fit. Sold as a set of four in black or neutral only. We have a large collection of used covers in all colors for all years.

Pressure die cast with show quality chrome. Easy to install, correct fit and finish, inexpensive way to spruce up your interior. Remember when we used to send these out and pay big money to have them replated? Sold as a pair, hardware included.

A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat back when positioned forward. This bracket carries a D7AA-69618C46-A or D7ZZ-69618C46-A service replacement part number. Without...

These are often cracked or collapsed causing your seats to lean back too far. One kit does one seat, two kits required per car.*NOTE* Don't discard your original screws! The screws supplied with this kit have a head that is just slightly smaller than original so when you really tighten the screws down the head goes right on through the stop! A very small washer will cure the problem if you choose to use the screws supplied. Replaces Ford Parts #: C8ZZ-6560310 & C8ZZ-6560311

Sold as a pair

Fits RH or LH standard interior, two required per car. Has correct grain texture and injection molded exactly like originals. Includes metal clip retainers pre-installed as well as the clips themselves. Use any solvent based paint to match the color of your interior. These were used on the 69 - 70 (and some 68) Mustangs but only used in 1970 for the standard model Cougar.Sold individually Replaces Ford part #: C9ZZ-6560762.

Fits RH or LH standard interior, sold individually, two required per car. Has correct grain texture and injection molded exactly like originals. Includes metal clip retainers pre-installed as well as the clips themselves. Available in black only, use any solvent based paint to match the color of your interior. These were used on the 69 - 70 (and some 68) Mustangs but only used in 1970 for the standard model Cougar. Replaces Ford part #: C9ZZ-6560762. ...

This dealer option was installed for people who were not comfortable with the height of their seats. This same kit was used on many intermediate Ford Products from 1965-1970. One kit does one bucket seat or one bench seat. Ford part # C6OZ-6362016-A. Click on images to enlarge. The screw on clips were included in the kit so the spacer would stay in place as the seat was guided into the four holes in the seat riser. Often these clips are cracked or missing and we cannot guarantee all four will...

Nice thick foam. Chromed mounting post. Includes base plate for seat. Keep in mind we have good used for less money, several colors available in good condition. Find them here.

We found that the plastic adjustment clip can break easily on these reproductions, so consider buying a good used original Ford part instead, for around the same price. Find it here.

Complete seat frame for the 1969 Eliminator or Mach 1 and all models in 1970. We highly recommend good used as they are more correct and significantly less expensive. These are dropshipped directly from the manufacturer. Passenger side shown.

Passenger side seat back release assembly, can me used for a conversion of 1970 high-backed seat backs for use in 1969 Mercury Cougar Eliminator and Ford Mustang Mach 1. This assembly has the release lever mounted nearly at shoulder level, factory 1970 high backs have the latch release at the hinge. This is a sneaky way to 'create' the factory 1969 high backed seats from 1970 seat backs. Comes with all hardware as shown. See picture for locating the three holes required for installation in a...

Used passenger side outer bucket seat black hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used passenger side inner bucket seat black hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat black hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used driver side outer bucket seat black hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Used passenger side outer bucket seat black hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand. Ford was slow about updating the casting number on some of these, some will have a C8ZB-6561694 number possibly. Ford number D0ZB-6561694. ...

Used driver side outer bucket seat black hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand. Ford was slow about updating the casting number on some of these, some will have a C8ZB-6561695 number possibly. Ford number D0ZB-6561695. ...

Used passenger side inner bucket seat dark blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat dark blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat dark blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used driver side outer bucket seat dark blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Used passenger side inner bucket seat red hinge cover, for any 1968-70 Mercury Cougar or1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat red hinge cover, for any 1968-70 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat red hinge cover, for any 1968-70 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used driver side outer bucket seat red hinge cover, for any 1968-70 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Used passenger side inner bucket seat light ivy gold / green hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat light ivy gold / green hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat light ivy gold / green hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used driver side outer bucket seat light ivy gold / green hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Used passenger side inner bucket seat nugget gold hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat nugget gold hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat nugget gold hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used driver side outer bucket seat nugget gold hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Used passenger side inner bucket seat white or parchment hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat white or parchment hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat white or parchment hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used driver side outer bucket seat parchment or white hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Used passenger side inner bucket seat light blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat light blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat dark light blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used driver side outer bucket seat light blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Used passenger side inner bucket seat light dark green hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat dark green hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat light ivy gold / green hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used driver side outer bucket seat dark green hinge cover, for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

This mirror came primarily on the 1968 Cougars, but have also been seen on the 1969. It has a twist lever to switch from day to night view. Comes in black only, case is of a hard plastic as opposed to the original hard vinyl case. The texture is not as heavy as original. Replaces Ford Part #: C7AZ-17700-G. This picture below shows the rear view mirror variations from 1967-1973. Check out this video ...

Reproduction light blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction pair of package tray retainers for your 67 - 70 Cougar or Mustang. Made from stamped steel with a black finish to keep them from rusting. They install in the front of the package tray, keeping it secure.

Good used passenger side plastic trim that will need repaint, and the screw hole hidden behind the dash pad is almost always cracked. The 1969 XR7 and Decor models used the padded version.Limited colors available, please specify in the notes when ordering as to which color you want and we will do our best to accomodate you.

Good used driver side plastic trim that will need repaint, and the screw hole hidden behind the dash pad is almost always cracked. The 1969 XR7 and Decor models used the padded version.Limited colors available, please specify in the notes when ordering as to which color you want and we will do our best to accomodate you.

Complete seat frame for the 1969 Eliminator or Mach 1 and all models in 1970. We highly recommend good used as they are more correct and significantly less expensive. These are drop shipped directly from the manufacturer. Passenger side shown.

Core passenger side (right hand) high back bucket seat for the Mercury Cougar. In most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Perfect for a 1969 Eliminator clone or to make your 1967-68 safer and more comfortable. If you are going to use these high backs in your 1967-69 Cougar, your existing seat...

This special bracket gets glued to the windshield. Rear view mirror bracket gets mounted to it. Glass bead blast it or just use a wire brush and it is ready to go!

Tired of your mirror falling out of adjustment? This installs easily and is correct in all details. Unlike the two piece unit we offer this one has the correct satin finish and correct screws. Replaces Ford Part #: C2SZ-17690-F. Reference from mercurycougar.net: Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when you're talking 'cause you're important to them. Greatest thing for...

Special cast-metal bracket glues to windshield. Fits the original and most reproduction mirror ball arms. This version is shiny chrome instead of satin silver like the originals. The screws are also incorrect. Otherwise nice quality.

This mirror came primarily on the 1969 Cougars, but have also been seen on the 1968. It has a forward /back flip lever to switch from day to night view. Comes in black only, case is of a hard plastic as opposed to the original hard vinyl case. The texture is not as heavy as original. Replaces Ford Part #: C7AZ-17700-G. This picture below shows the rear view mirror variations from 1967-1973. Check out this video ...

Restored rear view mirror lens for the Mercury Cougar or Ford Mustang. Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard.  We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens and send it in. Keep in mind glass is porous and is prone to staining. Often times these faint stains do not show up until...

These rear view mirror lenses are sold on an exchange basis.  Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens and send it in. Keep in mind glass is porous and is prone to staining. Often times these faint stains do not show up until the glass...

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

Reproduction rearview mirror lens for the Late 68 - 73 Cougar or Mustang. This lens is slightly smaller than the original, but fits well because the original mirror base does shrink over time. We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens. Keep in mind glass is porous and is prone to staining.  Check out this video Check out this video ...