All Available Parts - 1973 Ford Mustang

This is our heater cable for use with Mercury Cougars and Ford Mustangs with factory equipped A/C. The best part, its NOS, so you know it will fit right the first time! Ford part # C9ZZ-19988-A.

New old stock instrument voltage regulator Ford part number C9AZ-10804-ACheck out this video of our Gauge Tester

C9ZZ-19B888-A

NOS Ford key blank for ignition and doors.C7AZ-622053-A Sold Individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in...

C4DZ-5415-A Sold as a pair

Original used plastic upper radiator seal for 1971-73 Mercury Cougar and Ford Mustang with 26 inch radiators. Also called a radiator air deflector. Also fits 1970-71 Torino, Ranchero, Cyclone and Montego. As well as 1970-72 full sized Ford and Mercury cars. Comes with 4 original spring clips for mounting. Clips are not sold separately. Plastic portion originally measured 23-13/16 inches long.  Replaces Ford part number D0OB-8B170-B.

D1ZA-3B153-AA 1971 - 1973 Manual steering pitman arm. May also have casting number D3ZA-3B153-AB. Ford part number D1ZZ-3590-A.

D0AZ-62234A24-B New Old Stock power window regulator gear replacement kit. Fits 1969-73 Mercury Cougar and 1971-73 Ford Mustang. Doors and quarter windows.

C0TZ-13A024-A

D0ZZ-5493-A Rear sway bar bushing with 1/2" diameter opening. Used on rear anti-sway bar on the 1970 Eliminator and 70 - 73 models ordered with the competition handling package. Casting number as seen on the bushing is D0ZA-5484-E. Sold individually.

C9ZZ-18A318-B

C60Z-3047-A Used on many Ford products starting with the 1966 Ford Fairlane.

C7AZ-6571-B

D4AZ-18495-A

Sold as a set of three. Fits 1969-73 Mercury Cougar and Ford Mustang.Ford part number .

C8AZ-2B296-A

Original or NOS Ford distributor cap.

NOS new old stock intermittent wiper delay switch which is sometimes called the intermittent wiper delay module. The intermittent wiper delay switch can be identified by a grounding wire that is attached to the housing. Sometimes interval or delay is used in place of intermittent for this unit. *NOTE* Must be used in conjunction with an intermittent wiper controller. Replaces part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.

D0ZZ-15520-A Backup lamp switch that mounts to the factory 4 speed shifter linkage. 70 71 72 73 Mercury Cougar and Ford Mustang applications. NOS Autolite or Motorcraft switch number SW-943. Used with OEM installed Hurst Competition shifters. *Note - 4 speed switches are different than the manual 3 speed switches.

[No Description Provided]

NOS Ford key blank for trunk and glove box.Sold Individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but...

New old stock check valve for Bendix brake boosters. This is a white plastic check valve. Ford part number D0AZ-2365-A.Check the related items, for a reproduction rubber grommet.

(7526) Nylon plastic injected. New Old Stock. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where...

New old stock stainless clutch pedal pad trim. About 1/8 inches wider that the reproduction version. Replaces Ford Part #: C9ZZ-7B544-A.

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.

NOS white colored coat hooks pair. Reproductions only come in black, these are new in the package. White color started in 1970, off white and parchement 1968-69. Fits 1968-73 Mercury Cougar and Ford everything including that Mustang. Ford Part #: D0AZ-6229024-K.

NOS heater cable for 1969 - 1973 Cougars or Mustangs that are not equipped with factory air conditioning.Ford Part #: D1ZZ-18518-A

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

This rare accessory was only offered over the counter, it was not available as a factory option. Great upgrade for the 1970-1973 Cougar owner as cruise control was discontinued after 1969 and not offered again until 1974 on the Mercury Cougar.Ford part number C8OZ-9B742-AClick on images to enlarge. ...

Good used part without excessive rust or damaged rubber. For use with fixed column only. 1971-73 rag joints are different than the 1967-70 variety. The 1971-73 Cougar and Mustang steering box has a larger diameter shaft for attachment. Check out this video

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required.  NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Female buckle end seat belt for the 73 Cougar or Mustang. The face plate and spring assembly have been replaced on this belt, and has an aftermarket starburst button decal. The originals had the olive branch decal.  This is the actual belt you will receive. Measures 11-1/2" This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by...

Reproduction insulation located behind the kick panels on the 71 - 73 Cougar or mustang. Correct cut allows access to the door hinge bolts.

Good used bezel with appliqué still intact. Ford part number D1ZZ-13932-A.

Black ABS plastic replacement kick panels without speaker pods. Sold as a pair. Reproduction kick panels made for 1971-73 Ford Mustang, but will fit a 1971-73 Mercury Cougar OK.

Leather manual shift boot for the Classic Console Cruiser Console that we offer. Check out our video on rebuilding your shifter below: ...

Decent offshore reproduction but nothing beats the fit and finish of a good original FoMoCo part. Checkout our used as we have multiple colors in stock. This repro pad only comes in black. Replaces Ford part number D0AZ-3623-A.

These are cracked core wheels as taken from a parts car. The Center pad is not included and you can count on the rubber switch being rock hard. This wheel is for restoration purposes and we cannot guarantee that we will have all colors in stock at all times. The three wheels shown here are random examples and are not what you will actually be getting when you order. Most colors in stock, call for color, or leave desired color in the comments section of your order. Having issues with wobbly or...

This is an original chrome lock knob used on 1968 and up Fords with no peeling chrome or obvious scratches. If you compare the originals to the reproductions we have listed you will see a distinct difference. This is for the very particular restorer who really is concerned about detail, especially on prominent pieces like this. Sold individually, very limited supply.Original Ford part number is C8AZ-6221850-A

D1DZ-6561883-A Spring that keeps tension on the adjusting seat track latch, it keeps it locked. 1971 - 1973 Mercury Cougar and Ford Mustang Bucket Seats. We think that this later spring for the 1972 and up seats was a service replacement part.

Bucket seat track set for 1972 Mercury Cougar and Ford Mustang after 12/1/1971 and 1973 cars. Our premium grade used tracks are carefully inspected for damage prior to shipping. Most likely you will have to paint, but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Kit includes brackets D2ZZ-6561704-A and D2ZZ-6561705-A. *NOTE* Not compatible with the power seat option.

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

Core driver side (left hand) and passenger side (right hand) pair of bucket seats with center seat release for the Mercury Cougar or Ford Mustang. The seat frame is the same in the standard, decor or XR7 and are the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-7666700.*Note - Does not fit coupe, or fast back.

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that only two of your seat belts anchor, are under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D3ZB-7663120.*Note - Does not fit...

Core driver side (left hand) bucket seat frame with center seat release for the Mercury Cougar or Ford Mustang. This unit is the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket...

Used cigar or cigarette lighter socket and retainer assembly for 1971-73 Mercury Cougar and Ford Mustang. Ford part # D1ZZ-15052-A.

Round plastic window stop that attaches to the front and rear door window glass on all 1971-73 Mercury Cougar and Ford Mustangs. Two per door

Grade A used passenger side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260762, D3ZB-6561632, D1FZ-6260762, D2ZZ-6260762, and D3ZZ-6560762. We also...

Grade A used driver side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260763, D3ZB-6561633, D1FZ-6260763, D2ZZ-6260763, and D3ZZ-6560763. We also have B...

This desirable option was used only on the driver side seat of the LATE 71-73 Cougar and Mustang. This is for seats that have the seat release knobs on the outsides of the seats. The early 71's had the release in the center of the seat. It can be installed on the passenger side with no modification other than extending the wiring that runs under the carpet.  Before we send out a system it will have been tested and will work in all positions and will not show excessive wear or...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

D1ZZ-6523312-A Bracket that attaches the end of the power window motor to the door on the passenger side of 1971-73 Cougar and Mustangs with power windows.

D1ZZ-6523313-A Bracket that attaches the end of the power window motor to the door on the driver side of 1971-73 Cougar and Mustangs with power windows.

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the driver side door

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the driver side door

Used oil screen pick up tube assembly from a 1970-74 small block 335 series, or 351C or Cleveland Ford car. This is for front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: D1AZ-6622-A

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the driver side door

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

This pair of reproduction convertible top hooks are beautifully chrome plated and features correct thread size. Looks close to original. These hooks are actually for 71 - 73 Cougars and Mustangs, but will work just fine on the 69 - 70.

This is the "Chrome" trim across the top of the windshield on the inside. This piece will need to be sandblasted and repainted. Many people have chromed these, but because of Federal safety regulations from the factory they were painted satin silver.Ford Part Number: D1ZZ-7603606-A.

Detachable mounting plate for installing the convertible ram cylinder to the convertible top frame assembly behind the quarter interior panel. Right and left are the same, fits all 1971-73 Mercury Cougar and Ford Mustang convertibles. Ford part number D1ZZ-76531A19-A.

Driver side convertible frame assembly mounting and pivot bracket for all 1971-73 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Mounts behind the quarter interior panel.  Ford part number D1ZZ-7653119-A.

Passenger side convertible frame assembly mounting and pivot bracket for all 1971-73 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Mounts behind the quarter interior panel.  Ford part number D1ZZ-7653118-A.

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.

Used on the 1970 Mustang, 1970 - 1971 Cyclone and Torino and 1971 1972 1973 Cougar style steel wheel 14 x 7". Master Parts Catalog description: 15-1/4" O.D., 11" I.D., 2-3/4" wide. This grade A brushed beauty ring will look right at home on a low mile car, no curb rash!!! Ford part number D0ZZ-1210-B Ford superseded this part with part number in 1974 with D4WY-1210-A which looks the same just a little bit deeper at 2 7/8" deep ...

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide. No dings and only the slightest scratches.The part number is D0DZ-1210-A and the engineering number is D0DA-1210-B. Sold individuallyFits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972...

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide. No dings and only the slightest scratches.The part number is D0DZ-1210-A and the engineering number is D0DA-1210-B. Sold individuallyFits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972...

Used 14x6" stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will find out there and some have probably ridden in trunks most of their lives. Have a bent or damaged wheel? Don't have a spare? These have the larger center hub, and will fit the "Granada" disc brake rotors. Shipped bare. Various conditions, subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.Ford part # D0DZ-1007-B. ...

Used 14x7" stock stamped steel wheel for the Mercury Cougar and Ford Mustang / Torino. Rare seldom seen size most commonly found on a Ford Torino. These were offered from 1971 through 1973 on the Cougar and 1970 - 1973 on the Mustang and Torino. Have a bent or damaged wheel? Don't have a spare? Total width is 8" with a 4" backspacing. Various conditions and subject to availability. Used 'as is', wheel as found in the wild.Ford part # D0OZ-1007-B.

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

Rod used for locking the 4 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 13 inches long and was originally marked with a green paint mark.The 4 speed manual transmission, could not be ordered on the 351-2V engines. Only 351-4V's and 429CJ's in 1971, and 351CJ's (Q code) in both 1972 and...

Nice quality reproduction of the upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, and contours. Ford part number D1ZZ-7521-B.

Application for all 1971 - 1973 Cougars with a factory manual 3 and 4 speed transmission. Engine options include 351-2V, 351-4V, and 429CJ. Ford part number D1ZZ-6A023-B. If you have pictures, specs or one of these for sale we would like to hear from you.

Adapter plate for mounting the 4 speed shifter control assembly to the Top Loader transmission.Ford part # D1ZZ-7E046-B. Check out our video on rebuilding your shifter below: ...

D0ZZ-15520-A Backup lamp switch that mounts to the factory 4 speed shifter linkage. 70 71 72 73 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-943. Used with OEM installed Hurst Competition shifters. *Note - 4 speed switches are different than the manual 3 speed switches.

D1ZZ-15525-A 71 72 73 Mercury Cougar and Ford Mustang with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

Used upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, bushing, and contours. Ford part number D1ZZ-7521-B.

Used clutch pedal return spring with two original nylon bushings. Ford Part #: C8OZ-7534-B.

Equalizer bar or "Z" bar for 351 and 429CJ engines with a manual transmission. Used after 4-30-1971. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use. Ford part # D1ZZ-7528-C.*NOTE* Before 4-30-1971, use Ford part # D1ZZ-7528-A.

New Old Stock Ford flywheel. 11 inch clutch, 164 tooth ring gear,12-3/8 inch bolt circle for clutch pressure plate. Cast iron with C5AE-A and C7TE-A. New, never installed Ford manual transmission flywheel. Fits 351W, 351C, and 351CJ. Ring fear installed, factory fresh.

Original equipment 4 speed top loader transmission from a 1972 or 1973 Mercury Cougar with engine code Q - 351-4V only. This is a late transmission and was used starting 12-1-1971. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear.Ford part # D2ZZ-7003-H, casting # RUG-BJ1. Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for...

D2ZZ-7210-A Round chromed �Hurst� labeled shifter for all 1972 and 1973 Mercury Cougar and Ford Mustangs with factory installed 4 speed transmissions. Tough part to find loose, most will be attached to the correct vintage Hurst Competition shifter mechanism. These shifters will not come with the round shifter ball knob. Check out our video on rebuilding your shifter below: ...

Hurst built 4 speed manual shift control assembly for any 1972 - 1973 Mercury Cougar or Ford Mustang. This will have the round Hurst shifter lever. Includes shifter mechanism, shift rods, and shift lever. All in used condition.Ford part # D2ZZ-7400-Assembly Check out our video on rebuilding your shifter below: ...

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

Replacement seal with boot for all 1965-73 C4 Ford transmissions. Tail shaft and slip yoke seal. 

Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions. 

Replacement cork pan gasket for all 1965-73 C4 Ford transmissions. 

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1972 - 1973 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford casting # C9AP-7A020-C.

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some likely have some minor scrapes. These were not painted originally, may have light rust that will clean up. The best available, won't be in stock often. See our Grade B pans for less than half the price. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Original dipstick tube, originally painted yellow and is approximately 18-3/64" inches long. Application 1971 - early 1973. Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. For any 351 or 429CJ engine. Ford master part number D1ZZ-7A228-A. *NOTE* Only used until 11-1-1972.

Original dipstick or in Ford speak "Indicator - Oil Level" for C6 automatic transmissions. Application for 1970 Mercury Cougar and Ford Mustang with 351 engines and C6 automatic transmissions, code "U" on your door data plate. Ford part # D3ZZ-7A020-A, Ford part # D3ZP-7A020-A.

Original dipstick tube, painted yellow and is approximately 17-23/32" inches long. Application 1973 Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. Ford master part number D3ZZ-7A228-A. *NOTE* Only used after 11-1-1972.