All Available Parts - 1973 Ford Mustang

CRC contact cleaner is intended for cleaning sensitive electronics and electrical equipment. Great for cleaning edge connectors, buss bars, circuits, contacts, printed circuit boards, switches, circuit breakers, etc. Safe on most plastics.

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

This is a used windshield wiper delay governor, or module, and is a black box that mounts under the dash to the left of the radio. Sometimes called interval or delay wipers. *NOTE* Must be used in conjunction with a intermittent wiper switch.Part # D1ZB-17C476, D2ZB-17C476, MPC # D1ZZ-17C476-A.

This is a used intermittent wiper delay switch which is sometimes called the intermittent wiper delay module. The intermittent wiper delay switch can be identified by a grounding wire that is attached to the housing. Sometimes interval or delay is used in place of intermittent for this unit.*NOTE* Must be used in conjunction with an intermittent wiper controller.Replaces part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.

Includes the controller and switch to convert your standard two speed wiper system over to delay wipers.Controller part #  D1ZB-17C476, D2ZB-17C476, MPC # D1ZZ-17C476-A.Switch part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.

Aluminum flexible tube that connects the vapor canister to the air cleaner. To give this the look of the originals that had a black paper exterior coating you can spray paint it flat black. If anyone knows of a source to buy the original paper coated foil tubes we would like to hear from you. Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct.3ft long 7/8" O.D. 3/4" I.D. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A...

D3AZ-9D653-C Canister filled with charcoal or carbon particulates. Mounts in the rear side of the passenger side shock tower. *Note - These are 40 year old canisters, at this late stage the filtering ability of the particulates are probably not that effective for pollution testing. Primarily sold for concours judging.

D3DZ-9D664-A Bracket for mounting the charcoal canister to the body.

Ford called this part the fuel vapor separator. It mounts to the top of the fuel tank. This is part of the emissions control smog system, the fuel vapors that are collected in the charcoal canister are returned through a hose to this device into the fuel tank. Applications for this part include: 1971-73 Mercury Cougar and Ford Mustang, 1971-72 Pinto and Bobcat, 1971-72 Maverick and Comet, 1971 Thunderbird and Lincoln MKIII, and 1971-73 Ford / Mercury full sized cars. Starting about 1973, this...

Black paper wrapped aluminum flexible tube that connects the vapor canister to the air cleaner. This is as close to concours as we can find, 3/4 inch diameter, 36 inches long, and black outside, brown paper color inside.  Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A or D0AZ-9D667-A

Ford called this part the fuel vapor separator. It mounts to the top of the fuel tank. This is part of the emissions control smog system, the fuel vapors that are collected in the charcoal canister are returned through a hose to this device into the fuel tank. Applications for this part include: 1971-73 Mercury Cougar and Ford Mustang, 1971-72 Pinto and Bobcat, 1971-72 Maverick and Comet, 1971 Thunderbird and Lincoln MKIII, and 1971-73 Ford / Mercury full sized cars. Starting about 1973, this...

Used distributor modulator speedometer cable speed sensor for 1972 - 1973 Mercury Cougar and Ford Mustang. Mounts inline on a two piece speedometer cable. Ford master part number D2AF-9E731-A.

Used distributor modulator upper speedometer cable for 1971 - 1973 Mercury Cougar and Ford Mustang with the FMX or automatic transmission. Cable that connects the back of the speedometer and the speed sensor of the modulation system. Shown to be 10.54 inches long. 

Used wiring harness for the spark control box for the 1973 Mercury Cougar or Ford Mustang . This is only the harness, you can find the control box here.

Used control box for the spark control system on the 1973 Mercury Cougar or Ford Mustang. Ford part number D3AF9E447

D2ZZ-9A820-A Distributor modulator lower speedometer cable for 1972-73 Mercury Cougar and Ford Mustang. Shown to be 48 inches long.

New air cleaner breather element for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, includes cartridge holder, retainer clip and filter.

NOS air cleaner breather element filters for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, cartridge holder not included.Packaging may vary

NOS air cleaner breather element filter assembly for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, "AUTOLITE" marked also FA-79.  Casting number D0OF-9D696-A. Ford part number D0OZ-9D695-A.

Unique to the 1973 Mercury Cougar and Ford Mustang with 351 engines. This is only the upper section of a two piece ducting that connects to the air cleaner snorkel with a flex tube. The Ford MPC specifies that this is only for the 351-2V and 351-CJ (351-4V) engines.Replaces Ford part number D3ZF-9A624-A.

Aluminum Preheater hose that is used to preheat carburetor air. This 2" X 18" aluminum flex / stretch type hose attaches from the exhaust manifold shroud to the bottom of your air cleaner snorkel.  This hose is sold individually and does not come with clamps.If you prefer, you can grab the cloth type hose here.  ...

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Good used OEM original hood hinge set. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. Fits 1971-73 Mercury Cougar and Ford Mustang. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the springs.Ford...

Hood hinge spring for Mercury Cougar and Ford Mustang. Coil spring type with 6-1/4 inches of overall length. Sold individually, one per side. Ford part # D1ZZ-16789-A. *NOTE* Excludes 1971-73 Mustangs with ram air hood option.  

Good used OEM original passenger side hood hinge. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. It will be easier to fit and adjust the hinge prior to installing the spring on the hinge. Here is a helpful youtube video that shows you how...

Good used OEM original driver side hood hinge. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. It is easier to fit and adjust these hinges prior to installing the springs on them. Here is a helpful youtube video that shows you how to...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, marked with an "L". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number D1ZZ-6502667-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number C6OZ-6202639-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side upper only, marked with an "R". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number D1ZZ-6502666-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side lower only, marked with an "R". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number C6OZ-6202638-A.

Used upper rear fender brace that brace is visible when you open the door and look in the upper part of the fender void. Welds to the cowl on 1971-73 Mercury Cougar and Ford Mustang. Same tab either side. Ford part number D1ZZ-16A006-A.

Fuel tank spacer. Welds to the bottom side of the trunk pan. Spaces the tank, so that the fuel vapor separator assembly, isn't pinched. Easy to make these stands, and there are two needed, are approximately 1-1/2 inches tall. Strap is 1-1/8 inches wide.  

This 1965 Mustang alignment pin is not correct for the 1969 to 1973 Cougar but it will work. See the image to the left to see the comparison to an original 69 pin.

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

This is the storage bag that the convertible top cover folds into when the top is in the down position. Ford calls this part the "Folding top dust hood container." It is made from common vinyl top material and is always black. It measures 15"x27" and the bottom portion is sometimes, tapered down to 8". The same design was used for many Ford Products of the day including Torino, Montego and others. Current offering does not have a tapered bottom, it is square. Pictures will show both styles...

Used to cushion and protect top vinyl from excessive wear from side rails. Replaces Ford part #: D1ZZ-7652875.

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling.  See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps, so any boot that comes with snaps is not...

Replaces Ford Part #: D1ZZ-7650509-A

Replaces Ford Part #: D1ZZ-7650508-A

Reproduction hydraulic cylinder for the Mercury Cougar or Ford Mustang convertible equipped with the power top. Includes pictured pivot bushings.* - According to the manufacturer and the Ford Master Parts Catalog, 1971 Mustang would have originally used the passenger side cylinder (D1ZZ-7650600-A) for both sides.Replaces Ford Part #: D1WY-7650600-A, D1ZZ-7650600-A, D2ZZ-7650600-A

Exact fit, not generic 'One Size Fits All' hoses. Quality high pressure fittings. Contains both upper and lower Hydraulic Hose for a 1971, 1972 or 1973 Mercury Cougar or Ford Mustang Convertible Hydraulic CylinderClick on images to enlarge.

This driver side moulding is correct for convertible. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-7603599, D1ZB-6503599-aw, D3ZZ-7603599, D3ZB-6503599-aw *NOTE* Excludes...

Driver side stainless steel weather strip retainer for 71-73 Cougar and Mustang convertibles. This retainer screws to the windshield pillar post and holds the weather stripping for the front of your door window glass. Plan on replacing the weatherstripping. There is also the companion lower aluminum retainer listed on our site.These used stainless pieces generally polish up very well with 0000 steel wool. The little black plastic coated clip will be compromised due  to age and...

Passenger side stainless steel weather strip retainer for 71-73 Cougar and Mustang convertibles. This retainer screws to the windshield pillar post and holds the weather stripping for the front of your door window glass. Plan on replacing the weatherstripping. There is also the companion lower aluminum retainer listed on our site. These used stainless pieces generally polish up very well with 0000 steel wool. The little black plastic coated clip will be compromised due to age and heat.Replaces...

Excellent quality reproduction sun visor assembly for the convertible 1971-73 Mercury Cougar and Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. The original casting numbers as seen on the back side will read D1ZB-7604123-AE for the driver side and D1ZB-7604122-AE for the passenger side. Sold as a pair.Replaces Ford part numbers D1ZZ-7604144-A, D1ZZ-7604145-A, and D2ZZ-7604144-A, D2ZZ-7604145-A.

Used convertible top latch handle for the driver side (left hand) for the Mercury Cougar or Ford Mustang.Ford part # D1ZZ-7650509-A , casting # D1ZB-7650509-A

Used convertible top latch handle for the passenger side (right hand) of the Mercury Cougar or Ford Mustang.Ford part # D1ZZ-7650508-A , casting # D1ZB-7650534-AA

Reproduction tack strip for the rear bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the rear bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 Feet (60 inches) of material and will have to trim to fit your top. You can also...

Reproduction front tack strip for the front bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the front bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 feet (60 inches) of material and will have to trim the tack strip to fit...

Reproduction driver side (left hand) convertible top latch assembly for the Mercury Cougar or Ford Mustang.  

Reproduction passenger side (right hand) convertible top latch assembly for the Mercury Cougar or Ford Mustang.  

Used power convertible top pump, motor and reservoir for the Mercury Cougar or Ford Mustang convertible. We do offer an excellent reproduction which you can get right here, but nothing beats original FoMoCo. There is a difference in the space of the mounting bracket between the 1969-70, and 1971-73 Cougar or Mustang convertible top pump assemblies. Not to be interchanged.Our pumps are tested, we recommend flushing the pumps and reservoirs prior to installation. Save your grounding wire,...

14 piece bolt and screw set used to attach the convertible tack strip to the body. Kit comes with (12) 7/16 bolts and (2) phillips head screws. 

This used header will not be perfect as you can see from the pictures but it can be restored with some TLC. The part you get will be solid, we will not send you junk.Ford Casting Number: D1ZB-76514A72-AA

Driver side inner convertible top rail extension, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes as shown, be sure to save all of your installation hardware and bushings. Casting number on part reads: D1ZB-76631A09-A.

Passenger side inner convertible top rail extension, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes as shown, be sure to save all of your installation hardware and bushings. Casting number on part reads: D1ZB-76531A08-A.

Ground wire for convertible pump motor. Short wire section that attaches to the pump motor and grounds to the chassis of any 1969-73 Mercury Cougar or Ford Mustang. Easy to copy, #10 gauge wire about 11-1/2 inches long. Two ring terminals attached. Easy peasy.

Reproduction tips and screws for your convertible top welt. It's the strip that goes across the top back side of the convertible top. These are the decorative tips that go on each end of the welt.Each kit includes two tips and two screws.

No excuses 100% complete mechanism with no cracks, missing parts or heavy corrosion. We can include the top cylinders but will not guarantee they will not leak. We carefully break this down by removing the header and crossbows and placing the original bolts back in the holes. Once you get this from UPS it will be very evident how it goes back together.

This listing consists of 2 L shaped die cast side mouldings and one rear stainless moulding. We require clean cores for exchange prior to shipping. CORES MUST HAVE CLIPS AND STUDS IN PLACE. If you are in question as to whether your cores are acceptable or not, please send us several digital pictures. These differ from Mustang in that the Cougar has the center portion recessed with black semigloss paint. Our restored mouldings do not have the paint applied. The ford casting numbers as seen...

Our well (or boot) liners fit correctly. Made of heavy duty, textured vinyl.

Retainer and screws used to retain the header seal.Fits:1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang

This harness connects the convertible top switch to the pump on both the xr7 and standard 1969 - 1973 convertibles.

Galvanized three piece replacement tack strips for the 1971 - 1973 Cougar convertible. Over-sized, must be shipped via UPS.

Reproduction hydraulic cylinder for the Mercury Cougar or Ford Mustang convertible equipped with the power top. Includes pictured pivot bushings.* - According to the manufacturer and the Ford Master Parts Catalog, 1971 Mustang would have originally used the passenger side cylinder (D1ZZ-7650600-A) for both sides.Replaces Ford Part #: D1WY-7650601-A, D2ZZ-7650601-A

Nice reproduction of the convertible boot moulding for the 1971 - 1973 Ford Mustang, but also works on the 1971 - 1973 Cougar. *The Cougar originally would have had a different contour and a painted black stripe down the length of the moulding.

Keeper or retainer for attaching the convertible top cylinder pins. These are usually broken when replacing convertible top cylinders. One retainer per side.Ford Part # 372552-S These are not a exact replica of the t-bolt retainer, but will work for a replacement for the retainer on the T-bolt on the door windows (T-bolt Ford Part # C8SZ-6523274-A).  Ford part number for the retainer is C7SZ-65234A28-A.

Used 2 hole front mount center bracket for the sun visors for the Mercury Cougar and Ford Mustang convertibles.  Contrary to what the aftermarket says, these are slightly different from the 1968 'C8ZB-6504132' sun visor bracket. These colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your color in the 'comments section' of your order. We have these in a limited supply. Ford...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

New to the Market! Correct convertible side tension cables for the 71 through 73 Cougar and Mustang.  Replaces Ford Part #: D1ZZ-652806-A.  

Rear most convertible top bow #4, from a 1971-73 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached.   Ford part number D1ZZ-7651278-A.

Bolt for the under side convertible plate on any 1969-73 Mercury Cougar or Ford Mustang. 6 total bolts needed for attaching reinforcement plate to undercarriage. Sold individually. These are a close match to the original bolts, which are 3/8-16 x 1-1/2". Ford tightening specs. are 25-38 lbs. ft. torque.Replaces Ford number 57048-S2.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Driver side (left hand) front seat floor pan.  This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either...

These are exact replacements for 1964-68 Ford Mustang, but looks similar to the 1967-68 Mercury Cougar. This floor pan will also fit the 1969-73 Ford Mustang, but 1969-70 cars have different ribbing configurations. To use this pan in 1971-73 cars will require modification. This heavy gauged stamped steel floor pan starts behind the seat platform *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either bend it up or remove it and...

These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan *NOTE* This floor pan has the outside lip bent up which is proper for coupes. Convertibles were bent down. You can either bend it up or...

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 4 total per car, all 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped for the front seat belts inboard on 1971-73 cars. Round anchor bracket with factory welded nut for added strength. See related items for good used seat belt anchor plates if you have concours needs. Replaces Ford Part # D1AZ-6561216-A. ...

Floor tunnel body reinforcing plate for the floor shifter on any 1971-73 Mercury Cougar or Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than previous years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number D1ZZ-6512118-A.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

This is a great, well fitting reproduction and is also all you need to replace the firewall on your 71 - 73 Cougar or Mustang. This is the entire wall, from passenger side to driver side, cowl to floor pan. Made specific for cars with A/C.

Used driver side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Used driver side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Used passenger side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Used passenger side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Reproduction driver side (left hand) front inner apron for Mercury Cougar and Ford Mustang.

Reproduction passenger side (right hand) front inner apron for Mercury Cougar and Ford Mustang.

Reproduction stamped steel driver side (left hand) rear inner apron for Mercury Cougar or Ford Mustang.

Reproduction passenger side (right hand) rear inner apron for Mercury Cougar and Ford Mustang.

Used passenger side (right hand) shock tower in excellent condition as cut from a Western parts car. No specific part number for this structural front suspension section. Generic Ford part # D1ZZ-16054-A, includes apron and side member.

Used driver side (left side) shock tower that is in excellent condition as cut from a Western parts car. For Mercury Cougar and Ford mustang with no specific part number for this structural front suspension section. Generic part # D1ZZ-16055-A, includes apron and side member.

1971-73 shock towers are not reproduced and finding rust free Western aprons is getting to be a challenge. This is a great value for those needing multiple parts and want factory spot welds. Generic Ford part # D1ZZ-16055-A, includes apron and side member.