All Available Parts - 1972 Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used wire loom plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Keeps spark plug wires neat and orderly. Mounts on valve covers. Replaces Ford Part #: B8Q-12297-A.

Made of heat resistant black nylon. Keeps spark plug wires neat and orderly.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used black plastic clip that goes onto the lower center of the firewall of any 1969 Cougar or Mustang. Also found on the back of the instrument cluster on the 71 - 73. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is...

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.

Carburetor idle mixture screw caps like originally came on the cars from the factory. Exact reproduction of Ford part number C7AZ-9J500-A. This clip onto the idle mixture screws of any 1967-73 Autolite or Motor Craft carburetor 2100 or 4300. They also will fit the 429 Cobra Jet with Ford numbered Rochester Quadrajet carburetors in 1970-71. Sold as a PAIR.

New Street Avenger carburetor. The 350 CFM Street Avenger carburetor has great features such as optimized street calibrations...two vacuum ports for all necessary vacuum accessories, factory preset electric choke for easy startups, built-in fuel filters; and an included 3/8" fuel line connection so there are no unnecessary trips back to the parts store. Known to bolt in right out of the box. The Avenger series are the first carburetors to have a limited lifetime warranty. With a great...

Reproduction OE Steel Fuel Vapor Line for the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang with 5/16" Fittings

Reproduction two hole fuel line grommet for the Mercury Cougar or Ford Mustang.

Replaceable filter which attaches to original fuel sending unit. Fits 3/8" tube. Replaces Ford part #: D1AZ-9A011-A.

New replacement carburetor mounting gasket for 1970-73 Ford 351C or 351 Cleveland engines. Mounts between the fuel pump housing and the engine.

Reproduction fuel pump for all 1970-73 Mercury Cougars and Ford Mustangs equipped with the 351 Cleveland engine. 

These are the straps that hold the gas tank in place. 2 required, sold individually.Replaces Ford part number D1ZZ-9092.

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar

These are the straps that hold the gas tank in place. Sold as a pair.Replaces Ford part number D1ZZ-9092.

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

Reproduction anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount. Measures 16" X 12"

Used rear window glass in grade "B" condition for the Mercury Cougar or Ford Mustang coupe. Nice clean piece of glass with only minor scratches.

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss,...

Used grade "B" rear glass with the "Sun-X" green tint for the Mercury Cougar or Ford Mustang coupe. This is a nice clean piece of glass with only minor scratches. All air conditioning cars were supposed to always come with tinted glass, but we have documented cases of them coming with clear glass. Tinted glass was also available as an option in cars not equipped with A/C.

Brand new GREEN TINTED Tempered glass with no scratches or excuses. We guarantee this to be a perfect fit. This is a MUCH better way to go than peel and stick tint or the tint in an aerosol can... This glass does not have the faint Car-Lite markings in the corner but rather very bold

Brand new CLEAR Tempered glass with no scratches or excuses. We guarantee this to be a perfect fit. This is a MUCH better way to go than peel and stick tint or the tint in an aerosol can. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Perfect fit for your Cougar or Mustang with just the right amount of tint to keep you cool. This unit also comes with the heat defroster.

This clear rear window glass with the heat defroster is a perfect fit for your Cougar or Mustang.

This is a replica white plastic washer bottle / reservoir with black top & cap (D1TZ-17632-A)

Made by Trico who made them originally for Ford. Replaces Ford part #: D1ZZ-17528-A. Sold individually

Original black windshield wiper blade holder. Fits any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, two per car, 18" rubber wiper blade not included.Replaces Ford part #: D1AZ-17528-C or D3AZ-17528-A.

Injection molded high strength plastic connector for hoses leading to nozzles.Correct squared press-in fitting

Easy to install kit that converts your two speed wiper system to a variable speed system. These "off shore" units are spotty at best. We recommend our good used unit which you can get right here.

Original passenger side (right hand) wiper arm pulled off a 71 - 73 Mercury Cougar. Replaces Ford part #: D1ZZ-17526-A. Note: 1971 model year through 11/15/1970 uses the same wiper arm on both sides, which is the one used on the passenger side in the late 71 - 73 Cougars (Ford part #: D1ZZ-17526-A).

Original driver side (left hand) wiper arm pulled from a 71 - 73 mercury Cougar. Includes snap clip to hold the second arm in place. Replaces Ford part #: D1ZZ-17526-B. Note: 1971 model year through 11/15/1970 uses the same wiper arm on both sides, which is the one used on the passenger side in the late 71 - 73 Cougars (Part #: D1ZZ-17526-A).

CLEAR Glass without Shade; does not have Carlite logo, perfect fit. The most cost effective (and safest) way to ship these is when you buy several new pieces of glass and then we can drop ship them from the manufacturer via truck freight anywhere in the contiguous 48 for $110.00. We also sell the Window weld for the installation. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck...

Reproduction green tinted windshield that features a blue tinted band a crossed the top of the windshield. Not only will this unit look great, it will fit perfectly as well. Does not have Carlite logo. we also sell the Window weld for the installation. NOT for Sportsroof or Fastback models. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by...

Plastic housings with brass nozzles. Note that you may need to adjust the nozzles to achieve the desired aim.

This is a reproduction of a later service replacement version of the windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models).The original Ford part was part number C9AZ-17664-C

Original FoMoCo used two speed windshield wiper motor for your 1971-73 Mercury Cougar or Ford Mustang. This used motor comes with wiring harness, for all 1971-73 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1971-73 installation, must be marked 1Z. Linkage arms sold separately. Ford part #s D1ZF-17504, D2ZF-17504, D1ZZ-17508-A

Linkage arm that attaches to the windshield wiper motor that is unique to the 1971-73 Mercury Cougar and Ford Mustang. These are marked 1Z, among other things the slot is specifically indexed for the 1971-73 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Electrical wiring pigtail for the windshield wiper motors on any 71 - 73 Mercury Cougar or Ford Mustang. Plug with correct color wires and an adequate amount of wire length to make a repair or splice onto the newer motors without plugs.

Electrical junction block for use on 1971-73 XR7 models or 1971-73 Ford Mustang with options such as convertible, power seat, power windows, or rear defog. This combination insulator / junction block is for securing a circuit breaker, and mounts near the starter solenoid. Made from black Bake-O-Lite, Grade A used, may have some discoloring, but not damage.Replaces Ford part number D0SB-14448-A or D0SZ-14448-A.

Electrical junction block for use on 1971-73 XR7 models or 1971-73 Ford Mustang with options such as convertible, power seat, power windows, or rear defog. This combination insulator / junction block is for securing a circuit breaker, and mounts near the starter solenoid. Made from black Bake-O-Lite, Grade B, these will have some chipping or cracking present. Replaces Ford part number D0SB-14448-A or D0SZ-14448-A.

Finally a fast easy way to hook up the Pertronix Ignitor©! The Ignition Power Relay installs next to the starter solenoid with a supplied self-drilling, self tapping screw. Each wire is the right length and comes with the correctly sized terminal already Installed. Simply connect two wires at the solenoid and connect the Ignitor to the red power wire. The Pertronix Ignitor© is a 12 volt device that must be powered during crank and run. Many installers mistake the coil positive for a 12 volt...

Reproduction 2 speed windshield wiper switch for the Mercury Cougar or Ford Mustang. These "off shore" units are spotty at best.Replaces Ford Part #: D1ZZ-17553 or D1ZZ-17553-A

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

Tested and working used 2 speed windshield wiper switch for any 1971-73 Mercury Cougar and Ford Mustang. Replaces Ford part number D1ZB-17A553.

Used seat back release relay for the 71 - 73 Cougar or Mustang. Located on the relay panel behind the glove box. Ford part number D1ZB-14C690-AA

Used lead wire harness that runs from the white plug at the cowl to the throttle positioning sensor on the 71 - 73 Cougar or Mustang.Harness is red with yellow hash marks.

Used engine lift hook or hoist bracket for all 1970-73 351C engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. H code 351C-2V and M or Q code 351C-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We also...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Long block, factory H code 351-2V V-8 engine. 351 Cleveland engine rated at 177 Hp (net) with 8.6:1 compression ratio in 1971. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor, accessories, pulleys, and flex plate. Intake manifold...

Reproduction wiper arms for the 71 - 73 Cougar or Mustang. Sold as a pair.Replaces For Part number D1ZZ-17526-B

Reproduction keeper clip that attaches to the secondary articulating stabilizer arm and slides into place to secure the pin that holds the arm.

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem

Used windshield support bracket for any 1971-73 Mercury Cougar or Ford Mustang. One per side

Original FoMoCo used two speed windshield wiper motor mounting bracket for your 1971-73 Mercury Cougar or Ford Mustang. This used bracket comes with grommet for all 1971-73 Cougar and Mustangs. Ford part # D1ZZ-17496-B.

Good used D0OZ-17C583-A adjustable windshield wiper stop, as found on any 1971-73 Mercury Cougar, 1971-73 Ford Mustang, 1970-71 Ford Torino, or 1970-71 Mercury Cyclone. Cougar and Mustang use one of these in the center, not sure about the Torino.Will need new rubber dipped like OEM Ford. Replaces Ford part number D0OZ-17C583-A.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Gray plastic rod with rubber visor tip. Fits most 70's cars built by Ford. Replaces Ford Part #: D3AZ-6504114-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it wasn't on there computer. At WCCC they said they were not sure but looked...

Reproduction 2 screw rear mount sun visor bracket is only available in black, so plan on painting this unit to match. We have most other unfaded colors in used. Replaces Ford Part #: D1AZ-6504132-A or D3AZ-6504132-A.

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Nice chrome finish with Bulb. This was used on many Ford products but this bezel is 100% correct for the 1971-73 Standard Hardtop Cougar manufactured after 6/71, but will also work for all 1971-73 Cougars or Mustangs if you purchase the matching dome lens. No Cougar had a dome light in 1967-70. Ford Part # D6UZ-13788-A.

This was used on many Ford products but this bezel is 100% correct for the 1971 - 1973 Standard Hardtop Cougar manufactured after 6/71, but will also work for all 1971 - 1973 Cougars or Mustangs if you purchase the matching Bezel. No Cougar had a dome light in 1967-70. Ford Part # D1AZ-13783-B.

Used 2 screw rear mount sun visor bracket for the Mercury Cougar or Ford Mustang coupe. The MPC lists other part numbers such as D1ZZ-6504132, D2ZZ-6504132, and D3AZ-6504132, which are specific to some colors, but we have yet to seen them in a car. The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, so mention it in the 'comments' section of your order. Ford part # D1AZ-6504132,...

Pair of used wire anchors for keeping the rear most headliner bow stationary. These are fragile wires, and prone to rusting. We try to keep them in inventory. 1971-73 anchor wires are 4-9/16 inches long. A DIY person can improvise these pretty easy, using lengths of regular wire. Ford part # C6AB-6352180-A.

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

Ignitor 1 by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. There is also an upgraded Ignitor II available. -50F To 300F Working Temperature Range, 0-15,000 Rpm Range, This Easy To Install And Maintenance Free Electronic Ignition System Features Solid-State Electronics And Rotating Cobalt...

Ignitor II by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. Adaptive Dwell Control -  Dwell increases with RPM to provide an average of 4 times the available energy between 3000 and 5000 RPM and twice the available voltage at the plug. -50F To 300F Working Temperature Range,...

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

This passenger side moulding is correct for convertible. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503598 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-7603598. *NOTE* Excludes Mustang Fastback and Mach 1 models. ...

Visors are fully padded and covered with the correct vinyl or textured tier to match the headliner. Sold as a Pair.

Made from clear acrylic plastic with prisms added to increase the bulb brightness.Ford originally used white nylon with no prisms, which makes the light very dull. Replaces Ford Part # D1AZ-13783-B.

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these.  Sold Individually Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

This kit contains 500 hog rings, more than enough for two bucket seats and one bench seat.

These are often cracked or collapsed causing your seats to lean back too far. One kit does one seat, two kits required per car.*NOTE* Don't discard your original screws! The screws supplied with this kit have a head that is just slightly smaller than original so when you really tighten the screws down the head goes right on through the stop! A very small washer will cure the problem if you choose to use the screws supplied. Replaces Ford Parts #: C8ZZ-6560310 & C8ZZ-6560311

Core driver side (left hand) bucket seat with the side seat release lever for the Mercury Cougar or Ford Mustang. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket seat we can discard the upper portion. The...

Sold as a pair

Replaces Ford part #D1ZZ-6561692. Sold as a pair, available in black only. They can be painted but it is rather difficult to get paint to adhere long term. We have most colors available used, contact us for availability.

American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process.NOTE: These foam kits work well on the Standard and Decor interiors but you will find on the XR7 the lower portion does not work well.

Very nice reproduction knobs for 1971-73 Mercury Cougar and Ford Mustang with outboard mounted seat back releases. Also fits 1971 and newer Mercury Comet and Ford Maverick with bucket seats, as well as 1971 and newer Pinto. *Note - Not to be confused with the center mounted release knobs.

Core passenger side (right hand) bucket seat with the side seat release lever for the Mercury Cougar or Ford Mustang. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket seat we can discard the upper portion. The price...

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Only fits 1972-73 cars due to the seat belt location in the side panels. 1971 seats are a bit wider.Replaces Ford part number D2ZB-6563120.*Note - Excludes 1971 Mustang and Cougar.

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang coupe or hard top. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-6566700.*Note - Does not fit convertible.

Used RIGHT side bucket seat black hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used LEFT side bucket seat black hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used actuator for the seat back release on the 1971 - 1973 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

Hard to find New Old Recent Stock switch for the driver side power seat on the 71 - 73 Cougar or Mustang. Toggle switch looks accurate, however, you will need to reuse your original plugs. PLUGS NEED TO BE CHANGED FOR SPECIFIC APPLICATION. Some of the Ford part numbers include: D1WB-14B723-AA, D1WB-14B723-Ab, D2WB-14B723-AC, D1ZB-14B723-AA, D1ZZ-14A701-A, D2WY-14A701-A.

Used bezel for the driver side power seat switch on the 71 - 73 Cougar or Mustang. Ford part number D1ZB-14A706-AA This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Grade B used passenger side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade B will have scuffs and or scratches, might also be chalky in a couple of places. Various Ford part numbers associated with this panel, here are a few: D12B-6260762, D3ZB-6561632, D1FZ-6260762, D2ZZ-6260762, and...

Grade A used driver side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade B will have scuffs and or scratches, might also be chalky in a couple of places. Various Ford part numbers associated with this panel, here are a few: D12B-6260763, D3ZB-6561633, D1FZ-6260763, D2ZZ-6260763, and...

Used RIGHT side bucket seat medium brown / ginger hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634. ...