All Available Parts - 1972 Ford Mustang

Reproduction bushing for the master cylinder push rod where the switch and brake pedal converge. Two required per car and the bushings are sold separately.Ford part number C5DZ-2B129-B

New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.

These new brake drums are perfect replacements for tired and thin originals on you Cat or Pony. Fits cars with either the 2 1/4 inch or 2 1/2 Inch shoes. Front drums do not include studs or a hub. Drums Provide Consistent Quality & Reduced Noise.; Drums Are Vehicle Specific & Meet Federal Safety Standards.; Castings Meet Sae J431/g3000 Specifications For Proper Tensile Strength.; Machined To Control Perpendicularity & Run-Out For Optimal Performance & Brake Life.Also fits V8...

Used passenger (right hand) side brakes shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Right side screws are identified by an "R" on the end of the screw under the socket and a two grooves machined into the pivot nut. Original Ford part number for RH or passenger side is C2OZ-2041-A,...

Used driver (left hand) side brake shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Left side screws are identified by an "L" on the end of the screw under the socket and a single groove machined into the pivot nut. Original Ford part number for the passenger (right hand) side is...

Used drum brake distribution block for Mercury Cougar and Ford Mustang equipped with front drum brakes. This unit mounts to the driver side fender apron with two nuts. Bare block without brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # D0OZ-2B257-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Sold individually, phosphate & Oil (gray-black).

Reproduction driver (left hand) side drum brake self adjustor repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Reproduction drum brake backing plate hole cover plug. Replaces Ford Part # 8A-2092.

Complete reproduction front drum brake spring kit for Ford Mustangs equipped with 9" drums. This kit contains all the replacement springs and hold downs required to do a professional brake job on front drum brakes. Kit includes enough parts for two wheels.

Reproduction drum brake spring and hold down kit for Mercury Cougars or Ford mustangs equipped with 10"x2" drums. This kit contains all the replacement springs and hold downs required to do a professional brake job on 1969-73 Mercury Cougar or Ford Mustang 10" x 2" rear drum brakes. Kit includes enough parts for two wheels. *Hint - Use your camera phone to take pictures of your brake assembly prior to disassembly, and do one side at a time. Sort out and match all of the springs up exactly,...

Reproduction brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. These have 1/2 inch holes in them, like the originals.Replaces Ford part number C4UZ-2028-A.

Kit for rebuilding your drum brake distribution block for Mercury Cougar and Ford Mustangs. Special O-rings are made from EPDM (Ethylene Propylene 70 Durometer) which is specifically designed to withstand chemical degradation caused by prolonged exposure to brake fluid.Here’s a video to help you rebuild the distribution block so that you can corral your car without fearing for your life. Check out this video ...

New front10 X 2-1/2 inch brake shoes for the Mercury Cougar or Ford Mustang. These will fit the rears of some Ford vehicles, but not a Cougar or Mustang without modification.Typically this size of brake shoes is only found on the front of a Cougar or Mustang. You would have to have 2-1/2 rear backing plates in order to use these shoes on the rear of your car.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Reproduction passenger (driver hand) side drum brake self adjuster repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

C9ZZ-2A637-A Parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for RH or passenger side is C9ZZ-2A637-A. Clean Western part with no heavy corrosion like you see on Eastern cars.

Used parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for LH or driver side is C9ZZ-2A638-A. This unit is from a solid Western parts car, so you won't be getting one of those rusty East Coast units! Ford part # C9ZZ-2A638-A.

Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A

Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.

This kit contains all the replacement springs and hold downs required to do a professional job on 1972-73 Ford Mustang 10" x 1-3/4" rear drum brakes. Kit includes enough parts for two wheels. *Note - Kit does not include hardware for rear emergency brakes.

Rear Wheel Cylinder (29/32", Right Hand) Fits either Right Hand or Left Hand. Sold individually, 2 required per car. Replaces Ford Part #: C3OZ-2262-B and D2ZZ-2262-B.

Premium grade of rear brake shoes with semi metallic brake linings. 10 inch diameter drum brakes. Please measure your brake shoes, there are also 1-3/4 inch wide shoes too.

Quality replacement brake drum. # of Bolt Holes : 5 Inside Diameter : 254 mm Bolt Circle Diameter : 114.3 mm Brake Drum Surface Depth : 71.6 mm Center Bore Diameter : 61.8 mm Maximum Discard Diameter : 256.3 mm O.D. : 296.3 mm Replaces Ford Part #:C2OZ-1126-B

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for RH or passenger side original part Ford number is C9ZZ-2A637-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for LH or DRIVERS side original part Ford number is C9ZZ-2A638-A.

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya!Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Used brake hose support bracket for all 1971-73 Mercury Cougar and Ford Mustang. This attaches with two bolts to the driver side rear frame rail, it supports the flexible brake hose that goes to the rear axle. Ford had two versions of this part, picture shows the early version, later versions had a chunk cut off of the corner. Replaces Ford part number D1ZZ-2073-A, and D1WY-2073-A.

Push on retainer for rear drum brakes. 2 or 3 of these were used to hold the rear brake drums onto the rear axle assembly during construction of your 1967-73 Mercury Cougar or 1965 - 73 Ford Mustang. While not necessary, these are a neat concours item. Sold individually.  Ford part number 372188-S

Used emergency / parking brake assembly for the Mercury Cougar or Ford Mustang and is as removed from a West Coast Cougar organ donor. All parts are inspected and are good and ready for reuse.Ford part # D1WY-2780-A.

Used emergency / parking brake pedal pad that features all stainless steel construction. This unit cleans up very well with fine steel wool, has reusable folding tabs, and is easy to install. A great piece to finish off your interior!Replaces Ford part # C9ZZ-2A487-C.

Reproduction emergency / parking brake pedal pad trim piece for the Mercury Cougar or Ford Mustang. This great little reproduction looks good and is one of the little detail pieces that can separate a nice car from a mint car.Replaces Ford part # C9ZZ-2A487-C.

This used emergency / parking cable anchor bracket is spot welded to your passenger side (right hand) front floor pan and anchors the cable. Comes "as taken from parts car". *Customer Feedback* from mercurycougar.net: "Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting...

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford Part # C7ZZ-2A808-A.

Reproduction emergency / parking brake retainer clip set for the Mercury Cougar or Ford Mustang. These units are sold in a set of 3.

This reproduction emergency / parking brake spring for the V8 Mercury Cougar or Ford Mustang is made from original Ford blue prints. This is the oblong spring that is painted RED like the originals, rests upon the parking brake cross bar link between the shoes.These springs came from the factory in either Red or Yellow.You can find the Yellow spring here.Replaces Ford part # C2OZ-2601. ...

Premium, reproduction, and near concours correct front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. This cable hooks onto your inside foot activated brake assembly inside the car, through the floor board, and hooks to the brake equalizer cable under the car. This unit is very close to an OEM replacement, much better than our economy cable. ...

Reproduction emergency / parking brake cable for the Mercury Cougar or Ford Mustang with V-8 engines, that is approximately 133 1/8" long. This unit fits from equalizer to rear brakes and one is required per vehicle.Replaces Ford part # D0ZZ-2A635-A.

Reproduction emergency / parking brake cable return spring for the Mercury Cougar or Ford Mustang. This unit goes underneath the dash of the car and is a part of the emergency / parking brake assembly. Made from the original blue prints to the exact specifications of the originals.Original Ford specs according to the master parts catalog was: 11 1/8" long - 55 CoilsFord Part #: D1ZZ-2A651-A or D1ZZ-2651

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford part # C7ZZ-2A808-A.

This used emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle. Will most likely be missing pin.

This reproduction emergency / parking brake spring for the V8 Mercury Cougar or Ford Mustang is made from original Ford blue prints. This is the oblong spring that is painted YELLOW like the originals, rests upon the parking brake cross bar link between the shoes.These springs came from the factory in either Red or Yellow.You can find the Red spring here.Replaces Ford part # C2OZ-2601. ...

Premium grade reproduction driver side (left hand) rear emergency / parking brake cable. This is the short one, 31 inches, located on the driver side and is an exact fit for 1970 - 1973 Mercury Cougar and Ford Mustangs. Ford Part # D0ZZ-2A635-B

Reproduction concours correct premium grade passenger side (right hand) emergency / parking brake cable for the 1970-73 Mercury Cougar and Ford Mustang with V-8 engines. This is the long one on the passenger side (right hand) and measures approximately 133-1/8 inches long.

Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106. 

Driver side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1970-71 Mercury Cougar and Ford Mustang.

Passenger side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1970-71 Mercury Cougar and Ford Mustang.

Front emergency brake cable bracket that welds to the floor under the drivers side floor board.  It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted. Fits all 1971-73 Mercury Cougar and Ford Mustang.

NOS emergency / parking brake assembly for the 71 - 73 Cougar or Mustang still in Ford box and never installed.Ford part # D1WY-2780-A.

Passenger side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog. Ford part # C8OZ-2B292-A Check out this video Check out our caliper tips and tricks video below: ...

Driver side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog. Ford Part Number C8OZ-2B293-A Check out this video Check out our caliper tips and tricks video below: ...

Stamped steel bracket that mounts on the rear of the calipers. These often fracture or rust out. We only sell the pristine units, two required per car, PS and DS are the same. Ford part # C8OZ-2B295-A Check out this video Check out our caliper tips and tricks video below: ...

Reproduction grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. Replaces Ford part # B5A-1131.

This is a front brake grease dust cap tool. No more dented caps. These are milled from 6061 solid aluminum.

Cork gasket for the disc brake splash shield. Fits all 1968-73 Mercury Cougar and Mustang and 1968-71 Ford mid size including Torino, Cyclone, Ranchero, Fairlane.Replaces Ford part number C8OZ-2B160-A.

New front outer wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.865 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

New front Inner wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.378 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

This is a replica of the warning tag that came on positive (+) terminal of Autolite batteries when the 1967 - 1972 Cougars and Mustangs were shipped from the factory.

Replica of the coil spring shipping tag that would have been found on factory delivered 1967 - 1973 Cougars and Mustangs.

Replica antifreeze tag that would have been found on the 1970 - 1973 Cougars and Mustangs when they shipped from the factory. See the product images for an example of factory placement.

Reproduction Small Block Engine I.D. Bolt for the  1967 - 1973 Mercury Cougar / 1967 - 1973 Ford MustangSold individually 

This decal was available in both red and purple and both decals have the same Ford part number on them with the purple decal being slightly larger with more defined text. This is the purple version.Decal reads:Ford Dearborn, Mich. Air Conditioner Maximum Operating Charge 4LBS. 8OZ. of R-12 Complies With SAE-J639 Replaces part # D20E-19A688-AB

Available in Red and Purple. Both the red and the purple decals have the same Ford part number on them. The purple is a slightly larger decal, with more defined text. Decal reads: Ford Dearborn, Mich. Air Conditioner Maximum Operating Charge 4LBS. 8OZ. of R-12 Complies With SAE-J639 D20E-19A688-AB

Decal reads: Ford Dearborn, Mich. Air Conditioner Maximum Operating Charge 1LBS. 12OZ. of R-12 Complies With SAE-J639 D1ZA-19A688-AC

This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models with a BOSS 302 engine:1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang ...

This is a reproduction of the original white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-2V Regular Fuel followed by white background with blue lettering, Once a Month, Crankcase Ventilation System, Cooling System Flush, and a Motorcraft, Autolite parts logo. Located on the top of the air cleaner.  11-1/2 inch span, fits the smaller diameter air cleaner available in 1972.Fits the following models with a 351 2 barrel Regular Fuel engine:...

This is a reproduction of the original white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-4V Regular Fuel followed by white background with blue lettering, Once a Month, Crankcase Ventilation System, Cooling System Flush, and a Motorcraft, Autolite parts logo. Located on the top of the air cleaner. Fits the following models with a 351 4 barrel engine:1972 Cougar1972 Mustang ...

This is a reproduction of the white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-2V Regular Fuel followed by white background with blue lettering, Once a Month, Crankcase Ventilation System, Cooling System Flush, and a Motorcraft, Autolite parts logo. Located on the top of the air cleaner.13 11/16" from tip to tip, fits the larger diameter air cleaner available in 1972.Fits the following models with a 351 2 barrel engine: 1972 Cougar 1972 Mustang ...

This is a reproduction of the original white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-CJ Regular Fuel followed by white background with blue lettering, Once a Month, Crankcase Ventilation System, Cooling System Flush, and a Motorcraft, Autolite parts logo. Located on the top of the air cleaner. Fits the following models with a 351 4 barrel Cobra Jet engine:1972 Cougar1972 Mustang ...

Orange Vehicle Emission Control Information Decal for the 351 Cleveland with a 4 barrel carburetor and an automatic transmission in the 1972 Mercury Cougar and 1972 Ford Mustang late production. Printed with part number D2OE-9C485-BD.

Vehicle Emission Control Information Decal for the 351 Cleveland with a 2 barrel carburetor and an automatic transmission or a manual transmission in the 1972 Mercury Cougar and 1972 Ford Mustang. Printed with part number D2AE-9C485-HA.

Yellow Vehicle Emission Control Information Decal for the 351 Cleveland with a 4 barrel carburetor and an automatic transmission in the 1972 Mercury Cougar and 1972 Ford Mustang early production. Printed with part number D2OE-9C485-BD.

This decal goes on the tire jack itself.

Reproduction Space Save Tire Instructions Decal for the 1968 - 1973 Mercury Cougar / Ford MustangThis yellow sticker actually came out in 1971-ish. These were sent to previous owners of cars with space saver tires, with instructions to apply sticker to the space saver rim. We believe that they were factory installed with B.F. Goodrich space saver tires starting in 1971 for safety reasons. 

Reproduction Jack Instructions Decal for the 1971 - 1973 Mercury Cougar

The decal I most often see on the 1971-1973 Cougar is the used one pictured here. Will be trying to locate this decal soon.

For use on Hard Top / Coupe.

Reproduction Detroit Locker Glove Box Decal for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar

Reproduction Convertible Top Utica Plant Decal for the 1970 - 1973 Mercury Cougar or Ford Mustang 

This is an accurate reproduction of the tie down notice decal that was placed on the rear license plate frame. This was to remind dealers to remove the tie down plates that were used to secure the cars to the transport trains / trucks on their way from the factory to the dealers. Ford wanted to recycle these plates to save money, but dealers often didn't feel it was worth their time to remove the plates. Thus, many cars still have them. Check yours out! ...

Controversy abounds on which shrouds received these and which did not. It is our understanding that no early Cougars came from the factory with this decal installed. This decal first surfaced when Ford had major problems with their flex fans in the early 1970's. We will let you decide if it is correct for your application... This is placed on the top, center of the fan shroud.

Ignition coil silver decal stamped with:FAC-12029-A12 VOLTS AUTOLITE OLECUSE WITH EXTERNAL RESISTOR

Reproduction Autolite Fl - 1 Oil Filter Decal for the 1967 - 1972 Mercury Cougar or Ford Mustang 

Reproduction 60000 Mile 6 Month Lube Sticker for the 1967 - 1973 Mercury Cougar / Ford Mustang

Replaces Ford Part #: D2AF-12029-AA

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.

This decal can be used to overlay your replacement oil filter, so it looks more like a vintage original oil filter. Research indicates that the gold was primarily used on 66 and earlier, as was the red. They then phased the red/gold out and replaced it with the white oil filter printed with the Autolite logo.   1967 Cougar/Mustang could have come factory installed with either red or gold. 1967 - 1969 factory serviced cars could have gotten the red or gold until stock was...

Decal Text: Autolite EV-50 D0AZ-6A666-A Replaces Ford Part #: D0AZ-6A666-A.

Exactly like the originals. This group 27 battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars. Supplier misidentifies this part as D1ZZ-10732-B. Replaces Ford Part #: D0OZ-10732-B.

Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang

This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Replaces Ford Part #: D0OZ-10757-A.

This is the correct battery hold down clamp for the 1971, 1972 or 1973 Mercury Cougar & Ford Mustang. Ford Part #: D0OZ-10718-B. Note: The battery hold down clamp offered by many Mustang / Cougar vendors as "Concours Correct" is actually for the 1974 - 1978 Cougar /  Mustang.

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. For all 1972-73 Mercury Cougar or Ford Mustang with 43-55 AMP alternators and V-8 engines. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. For 1972-73 Mercury Cougar and Ford Mustang all with V-8 engines.Positive cable is 10 1/4" center to centerNegative cable is 42" center to centerGround wire is 41" center to center Replaces Ford Part # :...

This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.

Everything you need to hold the battery down on your 71 -73 Cougar or Mustang. Included in this kit are the two stainless steel J-bolts, the hold down bracket and the hold down clamp.

NOS service replacement battery tray, may not be exactly like the assembly line tray. Group 27 battery tray is typical for cars with air conditioning and higher amp alternators. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars.  Replaces Ford Part #: D0OZ-10732-B.

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Original used bracket, not reproduction. Replaces Ford Part #: D0OZ-10757-A.

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...