All Available Parts - 1972 Mercury Cougar

Original used speaker lead wiring harness pigtail for all 71 - 73 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the dash. Proper length for re-soldering to factory dash speaker.

This pigtail is for 72-73 Mercury Cougar and Ford Mustang with stereo speakers. Original passenger side used under dash speaker wiring harness pigtail for all 1972-73 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.

This pigtail is for 72-73 Mercury Cougar and Ford Mustang with stereo speakers. Original driver side used under dash speaker wiring harness pigtail for all 1972-73 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire.

Flexible high pressure replacement brake hose for front drum brakes that fits both passenger (right hand) and driver (left hand) sides. Sold individually, please remember to order two if a pair is needed.Replaces Ford part number D1ZZ-2078-E.

Flexible high pressure replacement brake hose for the driver (left hand) side on Mercury Cougar and Ford Mustang equipped with disc brakes.Replaces Ford part # D1ZZ-2078-B.

Flexible high pressure replacement brake hose for the passenger (right hand) side of Mercury Cougars and Ford Mustangs equipped with disc brakes.Replaces Ford part # D1ZZ-2078-A.

Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.

Copper crush washer for all disc brake hoses and calipers 1968-73 Mercury Cougar and Ford cars like Mustang. Size 0.39" x 0.62" x 0.062". Four needed per car, two per side (one on each side of the disc brake hose end) sold indiividually.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits in a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part #: C3OZ-2062-B, D2ZZ-2062-A, & D3ZZ-2062-A.

Reproduction passenger side (right hand) wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits into a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part # C3OZ-2061-B, D2ZZ-2061-A, & D3ZZ-2061-A.

Reproduction set of wheel cylinder link pins. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place.Sold as a set of four.

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

Reproduction wheel cylinder link pin. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Sold individually. Ford part number B7A-2042-A.

Reproduction master cylinder for the Mercury Cougar and Ford Mustang equipped with drum brakes. This unit is brand new, not rebuilt, and made from high quality American made parts.

Reproduction chrome master cylinder cap for the Mercury Cougar or Ford Mustang equipped with drum brakes. This quality reproduction has the correct lettering and is correct for 1970-73 Cougars and Mustangs. However, it fits and looks good on all 1967-73 Cougars and Mustangs with other under hood chromed goodies. Will also work fit any other 1967-73 Ford drum brake dual reservoir master cylinders.Replaces Ford part # C7AZ-2162, C9AZ-2162, and D3AZ-2162.*Customer Feedback from Mercurycougar.net*"...

The Cougar radio bezel at first glance looks much like the Mustang radio bezel. It does in fact carry a Cougar part number and has a slightly different shape to it. The most noticeable difference is the fifth screw hole at the top middle, Mustang does not have this hole. Keep in mind the AM-8 track used the same bezel but with an enlarged hole.This enlargement was done at the factory prior to plating and if you look at the back side you will see the cut line. This is a pit free bezel that has...

This plastic panel affixes to the radio bezel from the backside. Very rare item... For example, according to Kevin Marti, in 1971 only 1451 Cougars came equipped with this panel. The reason a car would be ordered radio delete from the factory was often the dealer knew he would have his sales people upgrade the customer to a stereo or 8 track. Sometimes people would special order their cars radio delete as they knew they would be taking a trip to the local stereo store within the first week....

Replace that old, pitted, and cut up radio bezel with this quality concours part. This is a Mustang piece that will work on your Cougar but is slightly different. The easiest way to identify a Mustang bezel from a Cougar bezel is that Mustang had four mounting holes and Cougar had five. Will need slight modification to fit Cougar. Replaces Ford Part #: D1ZZ-18842-A.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes and an automatic transmission. This unit is not for cars produced after 6/25/1972. Ford part # D1ZZ-6501508-C.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with a manual transmission and manual drum brakes. Not to be used in cars produced before 6/25/1972. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D3ZZ-6501508-A.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with an automatic transmission and manual drum brakes. This unit is for cars produced after 6-25-1972. Ford part # D3ZZ-6501508-C.

Bolt and nut for installation of disc brake pedals in any 1967-73 Mercury Cougar or Ford Mustang. See related items for plastic bushings and metal spacer.

Used passenger side (right hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane / Torino equipped with the 351cid or larger V8 engine.Ford part # C9OZ-2012-A. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

Used driver side (left hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar or Ford Mustang, and Fairlane / Torino equipped with 351 or larger V8 engines. Ford part # C9OZ-2013-B. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

This kit includes the 4 fine threaded "T" shaped studs (with nuts) that mount the backing plate to the spindle and the plate that goes on the inside of the backing plate. These are used parts that are not damaged or corroded, taken from a Western parts car.

Reproduction driver side drum brake spindle. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Reproduction pair of drum brake spindles. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Dome light bulb for the standard (non-XR7) 1791, 1972, or 1973 Mercury Cougar.

LED dome light bulb for the standard (non-XR7) 1791, 1972, or 1973 Mercury Cougar.

Reproduction 97 License Plate Light Bulb for the 1967 - 1973 Mercury Cougar

Reproduction 631 Glove / Luggage Compartment / Under Dash Courtesy / Trunk Light Bulb for the 1967 - 1973 Mercury Cougar

Correct Backup Light Bulb for the 1967 - 1968 Mercury Cougar. Owners Manual and shop manual incorrectly state the backup light bulb to be the 1156.

Brand new 1157 (dual-filament) exterior stop lamp / turn signal light bulb for the Mercury Cougar or any vehicle equipped with 1157 bulbs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. For even brighter...

The 67 -73 Cougar uses the 1157A (Amber) bulb for the turn signals.  This bulb will also fit other applications that require an 1157A or 1157NA bulb. Replaces bulb #: 1157A or 1157NA

Reproduction 1893 Interior Radio Light Bulb for the 1967 - 1973 Mercury Cougar

New 1895 bulb for the instrument clusters. *Note - The table and the owners manuals are wrong for the Visual Check Panel bulbs, Ford literature calls out a 1895 bulb, when in fact the correct bulb is 1891.

Reproduction 4001 incandescent (non-halogen) high beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 2-prong plug and mounts in the inboard position on the car.These are OEM wattage (50 watts) to work with the factory headlight switch, without the need to add relays like you would for higher wattage halogen bulbs.Replaces bulb number 4001. Sold individually, 2 required per car.

Reproduction 1892 Interior Exterior Light Bulb for the 1967 - 1973 Mercury Cougar

The second image shows an original GE 212-1 bulb. These bulbs are no longer available, they have been superseded by bulb 212-2 (first picture).

Reproduction 194 light bulb that can be used for your gauges, high beam indicator, clock, or turn signal indicators for the Mercury Cougar.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Front driver side wheel lip moulding. Fits all 1971-73 Mercury Cougars.Replaces Ford part number D1WY-16039-A.

Rear passenger side wheel lip moulding. Keep in mind we will take a restorable core moulding in partial trade on this very hard to find part.Replaces Ford part number D1WY-6529164-A.

NOTE: Some modification required to fit Cougars! These are actually 69-70 Mustang wheel lip mouldings, which have a different shape / contour. However, with a bit of massaging they can be made to fit the 71 - 73 Cougar. They are the closest alternative we have found that fits and looks reasonably good for much less than restored originals. Check out our video below, showing how easy it is to install these mouldings on a Cougar ...

Seatbelt warning light relay for most Ford Lincoln and Mercury cars. This one has a D2AB-10B924-AA part number, but should be the same as the C7AB-10B924-A relay, they are identical except for the part number and the inclusion of "Motorcraft". This is a timed relay that allows several seconds of illumination to your seat belt warning light.These are tested and guaranteed to work.

Low fuel relay for all 1971-73 Mercury Cougar XR7 models, body code 65F and 76F only. Stamped D1WF-10A968-AA. These are tested and working relays.Fits 1971 Cougar XR7 Fits 1972 Cougar XR7Fits 1973 Cougar XR7

Used in 1971-73 Mercury Cougars and Ford Mustang for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.25" x 13/16" and has a single green dot. Box is marked FASCO, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Ford part number D1MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1971-73 Mercury Cougar and Ford Mustang. This relay controls a buzzer as a reminder to turn off the headlights or remove the key, when the door is opened.Replaces Ford part number D1AB-10C838-A or D1AZ-10C838-A.

Used 20 amp circuit breaker for either 69 - 70 or 71-73 Cougars.Mounted on the Starter solenoid in 69-70 cougars for convertible tops or power windows, and also on 71-73 Standard Cougars for convertible tops, power windows, heated back light, power seats or seat back release.On the 71-73 XR7 the circuit breaker was mounted next to the starter solenoid on a junction block. Different wire diagrams, owner / shop manuals list this circuit breaker in both locations, possibly due to multiple...

31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX  cars.  *Excludes 351C-4v and 351CJ engines.

Sold individually, but two are required for the rear suspension. Replaces Ford 5630 shackle kits that include bushings C6DZ-5781-A.

Correct length and construction shackle for all 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Ships complete - 2 piece shackle with original nuts. New bushings not included, but recommended. Sold individually, but two are required for the rear suspension. These also fit 1970 - 1972 Ford Mustangs. Replaces Ford 5630 shackle kits that include bushings C6DZ-5781-A.

Set of 1-1/4" leaf spring rubber bushings for the rear eye of the spring. Sold in packages of 8, 4 per side. Correct shackle bushings for all 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: C6ZZ-5781-B & C6DZ-5781-A.

Set of 1" leaf spring poly bushings for the rear eye of the spring. Sold in packages of 8, 4 per side. Correct shackle bushings for all 1971 through 1972 Cougars manufactured between 10/70 and 9/71. 1 5/16" OD.5" ID1.25" insert depth. .25" lip Replaces Ford Part #: C6ZZ-5781-B & C6DZ-5781-A. May be Dropshipped

Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually

[No Description Provided]

These shocks are the as close to original specs as possible for the Mercury Cougar. This is the comfort shock for those looking for a softer ride. The KYB Gas-a-Just shocks use higher gas pressure to keep your tires glued to the road. The KYB Gas-a-Just shocks' velocity-sensitive valving system adjusts quickly to changing road conditions for maximum comfort in any situation. Their mono tube configuration eliminates aeration and foaming, their micro-smooth, hard-chromed pistons extend their...

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

Rear axle vent bolt for the 67 - 73 Cougar or Mustang. This bolt serves a dual purpose, as it also holds the brake line bracket in place on the axle tube.

Reproduction leaf spring center bolt for your 67 - 73 Mercury Cougar.

Used passenger side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used driver side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used passenger side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used driver side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

Replaces Ford Part # C1AZ-4529-A Sold individually. All applications, attaches the drive shaft U-Joint to rear end pinion yoke. 5/16 Inch Diameter #24 thread for 1 1/8 inch Bearing Caps.

One size fits all universal joint u-bolt kit. Complete kit required to attach universal joint to rear differential. This kit only works with the 1-7/8 inch U-joint caps. Many of the higher performance engines used 2 inch caps and the larger yokes.  Replaces Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

Reproduction universal joint that fits the transmission end of the drive axle on the Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). this unit includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E.

This reproduction universal joint is forged from high strength alloy steel that is crossed w/ an anti-corrosion coating. This unit also features a grease fitting for an extended life, and fits Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E. Span 3.30" cups 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number...

This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Reproduction universal joint forged from high strength alloy steel and crossed w/ and anti-corrosion coating. Fits the differential end of the drive axle on all 289, 302, 351 Windsor as well as most 351 Clevelands (See Chart). Includes a grease fitting for an extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Reproduction front universal joint that fits on transmission end of the drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-G.

Reproduction universal joint forged from high strength alloy steel that is cross w/ an anti-corrosion coating. This unit fits the transmission end drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (See Chart). this unit also features a grease fitting for an extended life. span 3.60" cup size 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-G.

This reproduction universal joint fits the differential end of the drive axle on all Eliminators and other cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. Replaces Ford part # C3AZ-4635-H.

Reproduction alloy rear universal joint for the Mercury Cougar or Ford Mustang. This unit is forged from high strength alloy steel crossed w/ an anti-corrosion coating. This universal joint fits the differential end of the drive axle on all Eliminators and cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. span 3.5" cup size 1.00" and 1.12" Replaces Ford part # C3AZ-4635-H. ...

These Linear springs are custom wound for the performance-oriented customer. These feature 600-pound/inch rating and will lower the car approximately one inch from stock. Painted black, sold as a pair. Note: If you look close at factory sales pictures from the day you will notice the cars sit about 1" lower in back than front. These springs will level the car out provided your rear leaf springs are not sagging.  Linear springs are the easiest to understand. When you think of a spring,...

Made from soft flexible rubber very similar to the OEM material. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. If you prefer polyurethane insulators, you can find them here. Replaces Ford Part #: C4DZ-5415-A.

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.