All Available Parts - 1971 Mercury Cougar

Used air conditioning thermostat switch for any 1971-73 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Cutler-Hammer for Ford. Ford part numbers D1ZA-19618-A or D1ZZ-19618-A.

Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

Air inlet damper door for any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1967-68 door, but with two small notches, instead of one. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare...

Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This is a GOOD match for 1967-68 Cougar parchement / off-white interiors. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not...

New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily.*NOTE* This item can only be shipped via UPS ground. No Foreign orders please. ...

Shaft or rod for air inlet damper door for any 1971-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. Similar to the 1969-70 version, but does have a different bend on the end. See related parts. Additionally fits Maverick and...

Shaft or rod for the evaporator damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft has a tab mounted on the lever, and is clocked differently than the 1969-73 version. The evaporator damper door allows air to pass over the evaporator in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related...

Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.

Shaft or rod for the A/C damper blower door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1969-73 shaft is clocked differently than the 1967-68 version. This air conditioning damper door is in front of the blower or fan in the center of the car. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number...

Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...

Air conditioning fan blower assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Used mounting bracket from a 1971-73 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Almost the same hose as was used 1969-70, Dearborn assembly line hoses have a ribbed section 1971-73. The 1969-70 versions, typically have the alligator texture on the outside of the hose.  Ford part # C9ZZ-19858. ...

Air conditioning fan blower BARE clam shell assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Air conditioning fan blower BARE clam shell assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. All bare sheet metal steel construction starting in 1971 until 1973. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port on the side.

Used extension or rod for the vacuum actuator for controlling the air restrictor door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the front of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C9ZA-18...

Used extension or rod for the vacuum actuator for controlling the fresh air door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the right hand end, of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting...

"B" grade used cable and knob assembly for opening the passenger side fresh air vent on 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Cable control mounts under the dash below the glove box. Cougar uses a different mounting bracket than the Mustang. B grade will have a broken mounting tab, but will otherwise have a good cable. About 23 inches in total length.Replaces Ford part number D1ZA-6501890-A.

Used cable and knob assembly for opening the driver side fresh air vent on 1971-73 Mercury Cougar without air conditioning. Cable control mounts through the dash in a special dash bezel. About 13 inches in total length.Replaces Ford part number D1WY-6501891-A.*Note - Does not fit Mustang.

Chromed plastic driver side fresh air "Vent" bezel. Mounts with the cable through a hole in the dash panel, just to the right of the vent register. Most all of these used bezels have a defect in the chrome plating along the bottom, not visible when installed.Replaces Ford part D1WA-18A405 (casting in the part), or D1WY-10852-B.*Note - Does not fit Mustang

Used mounting and indexing bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket goes behind the dash panel and keeps the vent cable attached and indexed correctly. A 7/16-14  hex nut is also needed for mounting the cable. (Sold separately)Replaces Ford part number D1WY-6501822-A.

Used mounting nut for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This nut screws onto the cable.  7/16-14  hex nut with 11/16" hex. (Sold separately)*Hint this is an easy to find hardware store nut, nothing else special about it.Replaces Ford part number 34670-S.

Used mounting bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket mounts to a tab on the fresh air vent, and keeps the cable stationary.  Replaces Ford part # D1WY-18C587-A.

Used steel bracket for mounting the passenger side fresh air vent cable to the bottom of the dash below the glove box. 1971-73 Mercury Cougar only.Replaces Ford part # D1WA-6501861-AC.*NOTE* Does not fit Ford Mustang.

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars without factor air conditioning. Cars with only the heater option had dual fresh air vents. This bezel is for the driver side fresh air vent register and control cable, it has a molded hole for the vent cable.Replaces Ford part number D1WB-65044A13-AC (cast on the part) or D1WY-6504393-A.

New clear plastic lens or face plate for the heater control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

D1ZA-18C433 lower heater duct to floor outlet for 1971-73 Mercury Cougar and Ford Mustang without air conditioning. Used grade "A" part and may have one very minor scuff. Ford number D1ZA-18C433-AD

Brand new athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life.Shirt specs:6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTaped neck and shouldersSeamless seven-eighths...

Brand new athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life.Shirt specs:6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTaped neck and shouldersSeamless seven-eighths...

Brand new athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life.Shirt specs:6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTaped neck and shouldersSeamless seven-eighths...

Brand new athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life.Shirt specs:6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTaped neck and shouldersSeamless seven-eighths...

Brand new athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life.Shirt specs:6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTaped neck and shouldersSeamless seven-eighths...

Brand new athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life.Shirt specs:6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTaped neck and shouldersSeamless seven-eighths...

Brand new ladies athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life. Shirt specs: 6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTapered neck and shouldersSeamless...

Brand new ladies athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life. Shirt specs: 6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTapered neck and shouldersSeamless...

Brand new ladies athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life. Shirt specs: 6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTapered neck and shouldersSeamless...

Concours correct heater hose for all Cougars and Mustangs built after 2/1/1970. Prior to that year, red striping was used. These hoses feature durable yellow striping, "Autolite" spelled out, and are dated LQ0H04A. Correct for all V-8 engines WITHOUT air conditioning. The hoses that are used on cars with A/C have a molded 90 degree elbow at the end that fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping...

Concours correct yellow striped heater hose for Cougars and Mustangs WITH factory or integral air conditioning. These hoses feature durable yellow striping with "Autolite" spelled out and dated LQ0H04A. Correct for all V-8 engines with A/C. The hoses feature a correctly molded 90 degree elbow that fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping shows! Replaces part # D1ZZ-18472-ACY ...

Reproduction heater blower motor for Mercury Cougar and Ford Mustang. Wiring will need to be spliced into your existing wiring harness. Save the squirrel cage and the heater motor mounting plate from your old unit because it is not included with this item.These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units....

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Our heater cores are the finest available anywhere for any price. Constructed from corrosion resistant copper and brass. A great buy for anyone who is sick of smelling anti-freeze and needing to make repairs to this vital part.Replaces Ford Part #: D1ZZ-18476-B. Check out our video below on how to replace a heater core! We used a '69 Cougar with AC, but many of the same concepts apply to other years. ...

Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.

Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.

Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1969-73 Cougars and Mustangs, but also on 1968 and newer Fairlanes, Torinos, Rancheros, Cyclones, and Montegos. Also installed on 1970 and newer Mavericks / Comets, plus 1971 and newer Lincolns.Ford part # C8OZ-18591-A.*Note - Excludes Heater with...

Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A

This used heater fan switch mounts to the rear of the heater control panel. It is a good working switch, wiring pigtail, and plug. Also, because it is original, it will fit right the first time. Save your knob, because this part does not come with one. If you don't have the knob, its OK, I know where you can get a mint set. KNOBS. Replaces part # D1ZZ-18578-A.

Complete used heater control assembly that includes a bezel / face plate, bracket control mounting plate, electrical switches, and vacuum switches. Functional, driver quality, heater control assembly. Knobs and light socket wiring harness not included. Replaces part # D1ZZ-18A651-A. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A silver paint pen (purchased from most artist...

Used fresh air vent found in the driver side kick panel of all 1971-73 Mercury Cougar without air conditioning. Replaces Ford part number D1WY-6501935-A.

Used fresh air vent duct found behind the driver side dash panel of all 1971-73 Mercury Cougar without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1WY-6501878-A.

Non-original style replacement clip for mounting the quarter window regulator arm to the window channel bracket on all 1969-70 Cougar and Mustang coupe and convertibles. This clip will work with either the 1969-early 1970 bracket and the late 1970 bracket. The late 1970 brackets used a unique spring steel clip that seldom is reusable. Sold individually, one each per window.

Reproduction roofrail weatherstrip seal clip and quarter window guide clip for the 1971

Used passenger side quarter window regulator for all 1971-73 Mercury Cougar and Ford Mustang with manual crank rear windows. Ford part number D1ZZ-6530306-A.

1971 - 1973 Mercury Cougar and Ford Mustang coupe clear glass for the passenger side rear seating area

1971 - 1973 Mercury Cougar and Ford Mustang coupe clear glass for the driver side rear seating area

1971 - 1973 Mercury Cougar and Ford Mustang coupe factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Glass does not ship with chrome seal divider. Ford part number D1ZZ-6529710-B....

1971 - 1973 Mercury Cougar and Ford Mustang coupe factory tinted glass for the driver side rear seating area

1971 - 1973 Mercury Cougar and Ford Mustang convertible factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Glass does not ship with chrome seal divider. Ford part number D1ZZ-7629710-B....

1971 - 1973 Mercury Cougar and Ford Mustang convertible factory tinted glass for the driver side rear seating area

1971 - 1973 Mercury Cougar and Ford Mustang convertible Grade B factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part number D1ZZ-7629710-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the...

1971 - 1973 Mercury Cougar and Ford Mustang convertible Grade B factory tinted glass for the driver side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part number D1ZZ-7629711-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom...

1971 - 1973 Mercury Cougar and Ford Mustang coupe Grade B factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part number D1ZZ-6529710-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear...

1971 - 1973 Mercury Cougar and Ford Mustang coupe Grade B factory tinted glass for the driver side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not included. Ford part # D1ZZ-6529711-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear...

Brand new TINTED Tempered glass with no scratches or excuses. We guarantee this to be a perfect fit. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Excellent upgrade for your Cougar or Mustang

Brand new CLEAR Tempered glass with no scratches or excuses. We guarantee this to be a perfect fit. This glass does not have the faint Car-Lite markings in the corner but rather very bold

New green tinted driver side glass for any 1971-73 Mercury Cougar or Ford Mustang Convertible. Replaces SUN-X tinted glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Used driver side (left hand) quarter window regulator for the Mercury Cougar or Ford Mustang. Manual crank windows only, power window regulators are different. Nothing beats or fits like FoMoCo!Ford part number D1ZZ-6530307-A

Used bracket for mounting the bottom of the quarter window guide to the car body. Fits all 1971-73 Mercury Cougar and Ford Mustang coupe and convertible (non fastback). "L" shaped bracket that designed for mounting and adjusting the rear quarter window.Replaces Ford part number D1ZZ-65298A56.

New green tinted passenger side glass for any 1971-73 Mercury Cougar or Ford Mustang Convertible. Replaces SUN-X tinted glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Good used driver side (left hand) quarter window guide for the 1971-73 Mercury Cougar or Ford Mustang. This unit will ship as shown. All brackets come with rubber bumpers installed. We may substitute a new bumper for a missing bumper. We recommend a thorough cleaning and a liberal amount of Sil-Glyde grease or equivalent during re-assembly. Ford part # D1ZZ-6529753-A.

Good used passenger side (right hand) quarter window guide for the 1971-73 Mercury Cougar or Ford Mustang. Ford part # D1ZZ-6529752-A.

This support bracket mounts to the lowest portion of the quarter window cavity. This bracket is installed before the lower guide bracket. Fits all 1971-73 Mercury Cougar models and 1971-73 Ford Mustang models including fastback or sport roof models. The exploded view of the quarter window parts can be found in the Osborn Body Assembly Manual for 1971-72. One for each quarter window

Quarter window upper stop bracket

Quarter window lower stop bracket

Quarter window guide roller with swivel head for all 1971-73 Mercury Cougar or Ford Mustang Coupe or Convertible. Three of these rollers per side

Cupped metal washer with center hole with flat sides for installing the two upper swivel rollers on the rear quarter windows. 2 per side 4 total per car. Fits 1971-73 Mercury Cougar and Ford Mustang Coupe and Convertible.Ford part number D1OZ-57263A86-A.

Used quarter window shoulder screw and nut for the 71 - 73 Cougar and Mustang.

New clear passenger side glass for any 1971-73 Mercury Cougar or Ford Mustang Convertible. Replaces Tempered clear glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold

New clear driver side glass for any 1971-73 Mercury Cougar or Ford Mustang Convertible. Replaces Tempered clear glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Used passenger side bracket for mounting the quarter window glass. Fits all 1971-73 Mercury Cougar and Ford Mustang coupe and convertible (non fastback). Bracket ships as shown

Used driver side bracket for mounting the quarter window glass. Fits all 1971-73 Mercury Cougar and Ford Mustang coupe and convertible (non fastback). Bracket ships as shown

New slotted pan head screw for mounting distributor points or condensers. Three total, per single advance Ford distributors. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x9/32". Sold individually, but you likely need 3. 

New phosphate dipped slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". Sold individually, you will need 2. 

Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.

Brass screw in plug for select Autolite distributor vacuum advance units from 1968-71, typically the banded single advance units factory installed. Solid brass, originals were not, we believe that they were cadmium plated. Solid plug, should be hollow, with a 3/4 inch hex head. Works as it should. Fits most all vacuum advance that have a plug in the end as shown. *Note, when removing the old plug, there is a spring and washer inside. 

3/8-16x7/8 Bolt for installation of idler, adjusting pulleys, and brackets, on most 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, up to 8-9 are typically used per car. 9/16" hex, washer head bolt.

3/8 washer for installation of idler, adjusting pulleys, and brackets, on some 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, 1-2 are typically used per car. 

Grade A used deluxe shifter handle in black. Nice used condition may have a hairline crack in the plastic on the bottom. No release button or set screw included. See related items for Grade B  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Grade B used deluxe shifter handle various colors. Please specify color in the notes, limited to stock on hand. Fair used condition will have at least one crack in the plastic. May also have slightly pitted chrome. No release button or set screw included. See related items for Grade A  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Internal tail shaft assembly from a FMX transmission. We only disassemble up to what you see in the picture.  *Excludes some FMX transmissions with 351C-4v in 1970. We do not have the larger diameter version available.

Internal tail shaft assembly from a C-6 transmission. We only disassemble up to what you see in the picture. 

Internal tail shaft assembly from a C4 transmission. We only disassemble up to what you see in the picture.  *Excludes later versions of C4 transmission that have thicker output shafts.

Bolt kit for installing the idler and adjusting pulley on any 1970-73 Mercury Cougar / 1970-73 Ford Mustang or 1970-73 Ford / Mercury with 302, 351W, and 351C engines. 4 bolts 3/8-16x7/8 inch washer head bolts and 1 thick 3/8 washer.