All Available Parts - 1971 Mercury Cougar

Rear axle vent bolt for the 67 - 73 Cougar or Mustang. This bolt serves a dual purpose, as it also holds the brake line bracket in place on the axle tube.

Reproduction leaf spring center bolt for your 67 - 73 Mercury Cougar.

Used passenger side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used driver side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used passenger side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used driver side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Concours rear axle vent hose for any 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Rubber hose that attaches to the metal nipple on the top of your rear axle housing. Fits 8 and 9 inch rear ends. Includes hardware as shown. Crimp clamp, screw clamp and bolt. Ribbed hose like original, and has yellow paint mark like from the factory. About 20 inches of hose is included, a little more than what was from the factory. Part number 4A001 in the chassis assembly manual.

All applications 1967-1973 Cougar and Mustang, attaches the drive shaft U-Joint to rear end pinion yoke. Sold individually, two required per car, complete with self locking pinch nuts. Perfect used, no rust or worn threads, these clean up nicely with your benchtop wire wheel.  Note, OEM came with fine threads and no lock washer.Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

Replaces Ford Part # C1AZ-4529-A Sold individually. All applications, attaches the drive shaft U-Joint to rear end pinion yoke. 5/16 Inch Diameter #24 thread for 1 1/8 inch Bearing Caps.

One size fits all universal joint u-bolt kit. Complete kit required to attach universal joint to rear differential. This kit only works with the 1-7/8 inch U-joint caps. Many of the higher performance engines used 2 inch caps and the larger yokes.  Replaces Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

Reproduction universal joint that fits the transmission end of the drive axle on the Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). this unit includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E.

This reproduction universal joint is forged from high strength alloy steel that is crossed w/ an anti-corrosion coating. This unit also features a grease fitting for an extended life, and fits Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E. Span 3.30" cups 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number...

This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Reproduction universal joint forged from high strength alloy steel and crossed w/ and anti-corrosion coating. Fits the differential end of the drive axle on all 289, 302, 351 Windsor as well as most 351 Clevelands (See Chart). Includes a grease fitting for an extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Reproduction front universal joint that fits on transmission end of the drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-G.

Reproduction universal joint forged from high strength alloy steel that is cross w/ an anti-corrosion coating. This unit fits the transmission end drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (See Chart). this unit also features a grease fitting for an extended life. span 3.60" cup size 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-G.

This reproduction universal joint fits the differential end of the drive axle on all Eliminators and other cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. Replaces Ford part # C3AZ-4635-H.

Reproduction alloy rear universal joint for the Mercury Cougar or Ford Mustang. This unit is forged from high strength alloy steel crossed w/ an anti-corrosion coating. This universal joint fits the differential end of the drive axle on all Eliminators and cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. span 3.5" cup size 1.00" and 1.12" Replaces Ford part # C3AZ-4635-H. ...

These Linear springs are custom wound for the performance-oriented customer. These feature 600-pound/inch rating and will lower the car approximately one inch from stock. Painted black, sold as a pair. Note: If you look close at factory sales pictures from the day you will notice the cars sit about 1" lower in back than front. These springs will level the car out provided your rear leaf springs are not sagging.  Linear springs are the easiest to understand. When you think of a spring,...

Made from soft flexible rubber very similar to the OEM material. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. If you prefer polyurethane insulators, you can find them here. Replaces Ford Part #: C4DZ-5415-A.

Standard size front sway bar bushings were 3/4 inch from 1967 - 1970. Rubber construction, sold in pairs only. Replaces Ford Part #: C7OZ-5493-C or C6OZ-5493-B.

Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-E

Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-J.

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

Bolt kit for installing front sway bar clamps to the body for any 1969-73 Mercury Cougar or Ford Mustang. 5/16" bolts for 1969-73 cars. Starting in 1969, the bolt size was changed from 3/8" to 5/16". We stock the 3/8" bolt kits, which was standard for 1967-68 cars. See related items.

Original sway bar mount for your 1971-73 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, right and left are the same. See related items.  

Used tachometer resistance wire for all 1971-73 Mercury Cougar XR7's and those that wish to add a factory tachometer to your standard instrument cluster. This wiring segment was removed from the main under dash harness of a 1971-73 Mercury Cougar XR7. No wires to splice. This wiring segment includes the plug to the tachometer, lead to the fuse block, and to pins, one goes to the ignition switch, the other goes to the 'thru the firewalll plug'.

Wiring pigtail for the AMP and Oil gauge cluster from a 1971-73 Mercury Cougar XR7. Pigtail includes the segment of the under dash harness that includes the 4 differently colored 90 degree rubber boot connectors for the gauges, and two light sockets, and at least 8 inches of wire.  Check out this video

Used wire set for the dash plug from the main under dash wiring harness from any 1971-73 Mercury Cougar. Wire colors may vary.

Used under dash wiring harness repair plug and pigtail to the brake pedal switch for the Mercury Cougar.

Used back up light socket and wiring pigtail for the 71 - 73 Cougar.

Used under dash wiring harness repair plug and pigtail to the turn signal switch for the 1971-72 Mercury Cougar, standard or XR7 model. This is part of the 14401 main under dash wiring harness. This plug is the same for Mustang and has the same wiring, the difference is that Mustang is wired different under the dash.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

New wiring pigtail with male bullet connector, and male / female paired connector. Also has rubber grommet that fits a 5/8" inch hole. Looks like 18 gauge wiring. These are remnants from the reproduction Mustang front turn signal lights that we convert to Cougar wiring. Brand new, approximately 13-15 inches in total length. Colors as shown.

Used under dash wiring harness repair plug and pigtail to the windshield wiper switch for the 1971 - 1973 Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair ignition switch plug and pigtail for your 1971-73 Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

Used passenger side (right hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part #...

Used driver side (left hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. It will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # D1ZZ-6521411-A.  *NOT* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in...

Used passenger side (right hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # D1ZZ-6521410-A.  *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the...

Door window glass grommet or washer to protect the glass for the Mercury Cougar or Ford Mustang. These units are placed under the bolts for mounting the window stops and the channel bracket. Used on most full and mid sized Ford

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the passenger side door

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the passenger side door

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the driver side door

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the passenger side door

Reproduction passenger side (right hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction passenger side (right hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction passenger side (right hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Complete six piece window glass set for the 1971

Reproduction six piece SUN-X or tinted glass set for the Mercury Cougar coupe equipped with or without power windows. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction CLEAR five piece glass set for the 1971-73 Mercury Cougar coupe or Ford Mustang hard top equipped with power or crank windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction TINTED five piece glass set for the Mercury Cougar coupe equipped with either power windows or crank windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Complete reproduction SMOKED glass set for manual crank.

Reproduction six piece extra dark tinted glass set for the Mercury Cougar coupe with manual windows. This set does not come with any of the window trim so save yours for reuse.

Four piece CLEAR window glass set for the 1971

Complete five piece window glass set for the 1971

Reproduction tinted four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with manually operated windows. This set does not include any window trim so save your for reuse. There are three versions of this glass. The clear version is just that

Reproduction tinted four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with power windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction clear four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with power windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Complete five piece window glass set for the 1971

Complete five piece window glass set for the 1971

Complete five piece window glass set for the 1971

Good used original door window regulator. Driver side with manual window crank

Good used original door window regulator. Passenger side with manual window crank

383278-S Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs.

384356-S Bolt with captured washer. Mounts the two stops and is used to install the channel assembly. Five total bolts per door glass, 10 used per car. Very specific sized captured washer for distributing pressure on the glass.Click on images to enlarge. 1970 similar. ...

D0OZ-6223318-A Used 1971-73 Mercury Cougar and Ford Mustang spring for the door window regulators. Same spring used on both power window regulators and manual window regulators.*Caution - These springs have an enormous amount of stored mechanical energy when installed

Used bolts, and usually new washers. Coupe kit comes with 4 - "A" bolts, 4 "B" bolts, and 2 "D" bolts, 12 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang coupes. Coupes or hard tops will have shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded.  There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list...

This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original starburst decal, which will be faded and need replacing. Find the replacement decals here. Spring is included.

Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...

This is the complete one piece seat belt buckle cover which comes with the face plate (with the round cutout for the push button) and the bezel all in one. This version is handy when you don't want to deal with multiple parts (as is the case with the separate face plate and bezel version). Simply remove your old cracked or broken cover, replace the metal spacer, and pop this cover into place and you're ready to go! You can use your existing spacer, or if you're missing one, you can find it...

This face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are going to be missing that piece, because after all......that dampener has been in there for up to 46 years! (this doesn't effect its useability). You can use your existing...

Used seat belt buckle bezel for the Mercury Cougar, Ford Mustang, or Ford Torino. This is the outer portion of the two piece seat belt buckle cover. This is a good replacement part if you want to keep your car original. These bezels will be free of cracks and breaks. Please specify which color you're looking for when ordering. Keep in mind that there are only a handful of colored buckles available, so we'll do our best to get you the color you need. Check out our video "All about seat belts"...

This is a general listing for anything and everything seat belt related. We can't go through and list every single seat belt part we have here, but chances are, we have what you need. If you're looking for used belts, all you have to do is call our seat belt guy (his name is Junior, at extension 209) and he'll go out in the warehouse and put together a set to match your needs and price range. We have everything from dirty old faded belts with minor rust on the chrome, to super nice, clean,...

This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.

This is the seat belt bezel located on the rear interior panel on your 72 - 73 Cougar or Mustang. Without it, your belt would retract back into the panel and you'd have to remove the whole thing just to get to the belt again. These bezels are very hard to come by, and we have yet to find anyone who reproduces them. Keep in mind that these bezels have been sitting for over 40 years, so the plastic has most likely become hard and chalky. When ordering, be sure to mention what color you need, and...

When placing your order, be sure to leave a note as to which color you're looking for and we'll do our best to find them for you. Limited quantities available. This colored face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are...

These reproduction face plates fit inside the buckle bezel on the two piece type seat belt buckle cover. Sold as a pair. You can use your existing spacer, or if you're missing one, you can find it here. Check out our video "All about seat belts" below. ...

Now you can restore your 1968-72 Cougar or Mustang’s deluxe seat belt buckles back to their original showroom condition by replacing cracked, broken, or missing components with the new seat belt buckle restoration kit. Tooled to the original factory specifications from OEM quality injected molded black plastic. This seat belt buckle kit features the correct texture grain pattern and starburst medallions for a perfect restoration. The release button and spring are included. One kit does a pair...

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

Finally! A cure for those peeling chrome bezels on your car with deluxe seat belts. If your plastic bezels on your 68-72 standard belts are two part construction, you can upgrade with these attractive bezels. Before these were reproduced we used to hunt high and low for good used units from rear belts out of parts cars. Perfect fit and great quality. Sold as a pair, six per car on coupes, four per car required on convertibles. Replaces Ford part # C8AZ-65611A72-A

Used chrome moulding that attaches horizontally to the bottom of the headlight bucket. Passenger side for any 1971-73 Mercury Cougar. 1973 used a different casting number but the parts are exactly the same. B grade will have some freckling in the chrome, and maybe a few pits and or other minor blemish. We consider these 'driver quality' rather than 'show quality'. We do offer an A Grade version of this part, but we seldom have them in stock.Replaces Ford part number D1WB-13B166-AB...

Used chrome moulding that attaches horizontally to the bottom of the headlight bucket. Driver side for any 1971-73 Mercury Cougar. 1973 used a different casting number but the parts are exactly the same. B grade will have some freckling in the chrome, and maybe a few pits and or other minor blemish. We consider these 'driver quality' rather than 'show quality'. We do offer an A Grade version of this part, but we seldom have them in stock.Replaces Ford part number D1WB-13B167-AB...

Used chrome moulding that attaches horizontally to the bottom of the headlight bucket. Passenger side for any 1971-73 Mercury Cougar. 1973 used a different casting number but the parts are exactly the same. A grade will have nice chrome, and maybe one minor blemish. We consider these 'show quality' rather than 'driver quality'. We do offer a B Grade version of this part, and always have them in stock.Replaces Ford part number D1WB-13B166-AB and D3WB-13B166-AA.

Used chrome moulding that attaches horizontally to the bottom of the headlight bucket. Driver side for any 1971-73 Mercury Cougar. 1973 used a different casting number but the parts are exactly the same. A grade will have nice chrome, and maybe one minor blemish. We consider these 'show quality' rather than 'driver quality'. We do offer a B Grade version of this part, and always have them in stock.Replaces Ford part number D1WB-13B167-AB and D3WB-13B167-AA.

This 14 piece grille package is only sold on an exchange basis and your cores must be received before we can ship. Often times a minor crack or two in the center grille or corner marker bezels can be repaired at no extra cost. Cores cannot show excessive pitting. We do give in-store credit for extra parts sent, call before you send to see if they are eligible. If you are in question on whether your cores are acceptable for exchange, emailing us several pictures is a good idea.

This rechromed grille has had any minor cracks / brakes repaired and has been replated. You will need to apply detail paint.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If you pay the core charge and we send your parts out in advance of getting...

Restored inner, small moulding that attaches to the driver side vertical grille support. Fits any 1971, 1972, or 1973 Cougar. We also have grade A and B used trim. See related items.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If you pay the...

Restored inner, small moulding that attaches to the passenger side vertical grille support. Fits any 1971, 1972, or 1973 Cougar. We also have grade A and B used trim. See related items.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If you...

Restored Hood peak or hood lip trim for any 1971 or 1972 Mercury Cougar. We also have grade A and B used hood mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If you pay the core charge and we send your...