All Available Parts - 1971 Ford Mustang

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 4 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-4V engines. This gasket set includes a metal valley pan.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-2V Cleveland engines. ...

This is a set of four 7/16 nuts that are used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. 

This is the complete eight piece kit that includes four 7/16 nuts and four studs (1 3/8") which are double threaded. One end is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with NO spacer.

This is the complete eight piece kit that includes four 7/16 nuts and four double threaded studs (1 3/4"). One end of the stud is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with 1/4" to 3/8" spacers.

Set of 20 bolts for the intake manifold on any 1970-71 Ford 429 Cobra Jet engine. 429CJ engines were optional in only in 1971 on Mercury Cougar and Ford Mustangs. Available in 1970 on B body Torino, Cyclone, Ranchero, Fairlane. *Note - Excludes Boss 429 engines.

New reproduction of Ford part number D0OZ-9S500-A, Hi Temperature choke gasket for all 1970-71 429 Cobra Jet engines. Must utilize the stock Ford cast iron 429 Cobra Jet intake manifold. Fits J and C code 1971 Mercury Cougar and Ford Mustang, and J and C code 1970-71 Ford Torino, Ford Ranchero, Mercury Cyclone.*Note - Excludes 429 Super Cobra Jet engines which used a different intake manifold.

Used cast iron choke stove from any 1970-73 351C-2V Ford engine. This is held on with 4 bolts, and to our knowledge no block off plate is reproduced. Casting number on the iron plate is D0AE-9A705-D, which is only for the plate. The plate and coiled tube assembly has a Ford part number of D0AZ-9C869-B. No hardware included.

Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-4V engine. AMK F-1321.*Note - Excludes 351C-2V and 351W engines.

Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-2V engine. AMK F-1313.*Note - Excludes 351C-4V and 351W engines.

New gaskets for installing your 429 Cobra Jet intake manifold. This is the Felpro branded gasket. Fits 1970-71 Ford 429CJ engines. 1971 Mercury Cougar and Ford Mustang with J or C code 429CJ engines. Intake to cylinder head gaskets and intake end pieces, along with O ring for distributor. *Note - Excludes N code 429-4V or Thunderjet, passenger car engines.

5/16-24 hex nut 7/16" head that is used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. Sold individually. AMK B-12786

New replacement carburetor mounting gasket for 1970-73 Ford 351C or 351 Cleveland engines. Mounts between the fuel pump housing and the engine.

Reproduction fuel pump for all 1970-73 Mercury Cougars and Ford Mustangs equipped with the 351 Cleveland engine. 

These are the straps that hold the gas tank in place. 2 required, sold individually.Replaces Ford part number D1ZZ-9092.

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar

These are the straps that hold the gas tank in place. Sold as a pair.Replaces Ford part number D1ZZ-9092.

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

Reproduction anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount. Measures 16" X 12"

Used rear window glass in grade "B" condition for the Mercury Cougar or Ford Mustang coupe. Nice clean piece of glass with only minor scratches.

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss,...

Used grade "B" rear glass with the "Sun-X" green tint for the Mercury Cougar or Ford Mustang coupe. This is a nice clean piece of glass with only minor scratches. All air conditioning cars were supposed to always come with tinted glass, but we have documented cases of them coming with clear glass. Tinted glass was also available as an option in cars not equipped with A/C.

Brand new GREEN TINTED Tempered glass with no scratches or excuses. We guarantee this to be a perfect fit. This is a MUCH better way to go than peel and stick tint or the tint in an aerosol can... This glass does not have the faint Car-Lite markings in the corner but rather very bold

Brand new CLEAR Tempered glass with no scratches or excuses. We guarantee this to be a perfect fit. This is a MUCH better way to go than peel and stick tint or the tint in an aerosol can. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Perfect fit for your Cougar or Mustang with just the right amount of tint to keep you cool. This unit also comes with the heat defroster.

This clear rear window glass with the heat defroster is a perfect fit for your Cougar or Mustang.

This is a replica white plastic washer bottle / reservoir with black top & cap (D1TZ-17632-A)

Made by Trico who made them originally for Ford. Replaces Ford part #: D1ZZ-17528-A. Sold individually

Original black windshield wiper blade holder. Fits any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, two per car, 18" rubber wiper blade not included.Replaces Ford part #: D1AZ-17528-C or D3AZ-17528-A.

Injection molded high strength plastic connector for hoses leading to nozzles.Correct squared press-in fitting

Easy to install kit that converts your two speed wiper system to a variable speed system. These "off shore" units are spotty at best. We recommend our good used unit which you can get right here.

Original passenger side (right hand) wiper arm pulled off a 71 - 73 Mercury Cougar. Replaces Ford part #: D1ZZ-17526-A. Note: 1971 model year through 11/15/1970 uses the same wiper arm on both sides, which is the one used on the passenger side in the late 71 - 73 Cougars (Ford part #: D1ZZ-17526-A).

Original driver side (left hand) wiper arm pulled from a 71 - 73 mercury Cougar. Includes snap clip to hold the second arm in place. Replaces Ford part #: D1ZZ-17526-B. Note: 1971 model year through 11/15/1970 uses the same wiper arm on both sides, which is the one used on the passenger side in the late 71 - 73 Cougars (Part #: D1ZZ-17526-A).

CLEAR Glass without Shade; does not have Carlite logo, perfect fit. The most cost effective (and safest) way to ship these is when you buy several new pieces of glass and then we can drop ship them from the manufacturer via truck freight anywhere in the contiguous 48 for $110.00. We also sell the Window weld for the installation. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck...

Reproduction green tinted windshield that features a blue tinted band a crossed the top of the windshield. Not only will this unit look great, it will fit perfectly as well. Does not have Carlite logo. we also sell the Window weld for the installation. NOT for Sportsroof or Fastback models. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by...

Plastic housings with brass nozzles. Note that you may need to adjust the nozzles to achieve the desired aim.

This is a reproduction of a later service replacement version of the windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models).The original Ford part was part number C9AZ-17664-C

Original FoMoCo used two speed windshield wiper motor for your 1971-73 Mercury Cougar or Ford Mustang. This used motor comes with wiring harness, for all 1971-73 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1971-73 installation, must be marked 1Z. Linkage arms sold separately. Ford part #s D1ZF-17504, D2ZF-17504, D1ZZ-17508-A

Linkage arm that attaches to the windshield wiper motor that is unique to the 1971-73 Mercury Cougar and Ford Mustang. These are marked 1Z, among other things the slot is specifically indexed for the 1971-73 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Electrical wiring pigtail for the windshield wiper motors on any 71 - 73 Mercury Cougar or Ford Mustang. Plug with correct color wires and an adequate amount of wire length to make a repair or splice onto the newer motors without plugs.

Reproduction wiper arms for the 71 - 73 Cougar or Mustang. Sold as a pair.Replaces For Part number D1ZZ-17526-B

Reproduction keeper clip that attaches to the secondary articulating stabilizer arm and slides into place to secure the pin that holds the arm.

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem

Used windshield support bracket for any 1971-73 Mercury Cougar or Ford Mustang. One per side

Original FoMoCo used two speed windshield wiper motor mounting bracket for your 1971-73 Mercury Cougar or Ford Mustang. This used bracket comes with grommet for all 1971-73 Cougar and Mustangs. Ford part # D1ZZ-17496-B.

Good used D0OZ-17C583-A adjustable windshield wiper stop, as found on any 1971-73 Mercury Cougar, 1971-73 Ford Mustang, 1970-71 Ford Torino, or 1970-71 Mercury Cyclone. Cougar and Mustang use one of these in the center, not sure about the Torino.Will need new rubber dipped like OEM Ford. Replaces Ford part number D0OZ-17C583-A.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Gray plastic rod with rubber visor tip. Fits most 70's cars built by Ford. Replaces Ford Part #: D3AZ-6504114-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it wasn't on there computer. At WCCC they said they were not sure but looked...

Reproduction 2 screw rear mount sun visor bracket is only available in black, so plan on painting this unit to match. We have most other unfaded colors in used. Replaces Ford Part #: D1AZ-6504132-A or D3AZ-6504132-A.

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Nice chrome finish with Bulb. This was used on many Ford products but this bezel is 100% correct for the 1971-73 Standard Hardtop Cougar manufactured after 6/71, but will also work for all 1971-73 Cougars or Mustangs if you purchase the matching dome lens. No Cougar had a dome light in 1967-70. Ford Part # D6UZ-13788-A.

Nice chrome finish. This was used on many Ford products but this bezel is 100% correct for the 1971 Standard Hardtop Cougar manufactured before 6/71. No Cougar had a dome light in 1967-70. Ford Part # D0AZ-13788-A.

Great fit. There were two different mounting tab styles used in the 1970's, this one is 100% correct for the 1971 Standard Hardtop Cougar manufactured before 6/71 and fits the early 1971 housing we sell. Ford Part # C6OZ-13783

This was used on many Ford products but this bezel is 100% correct for the 1971 - 1973 Standard Hardtop Cougar manufactured after 6/71, but will also work for all 1971 - 1973 Cougars or Mustangs if you purchase the matching Bezel. No Cougar had a dome light in 1967-70. Ford Part # D1AZ-13783-B.

Used 2 screw rear mount sun visor bracket for the Mercury Cougar or Ford Mustang coupe. The MPC lists other part numbers such as D1ZZ-6504132, D2ZZ-6504132, and D3AZ-6504132, which are specific to some colors, but we have yet to seen them in a car. The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, so mention it in the 'comments' section of your order. Ford part # D1AZ-6504132,...

Pair of used wire anchors for keeping the rear most headliner bow stationary. These are fragile wires, and prone to rusting. We try to keep them in inventory. 1971-73 anchor wires are 4-9/16 inches long. A DIY person can improvise these pretty easy, using lengths of regular wire. Ford part # C6AB-6352180-A.

Everything you need to hold the battery down on your 71 -73 Cougar or Mustang. Included in this kit are the two stainless steel J-bolts, the hold down bracket and the hold down clamp.

NOS service replacement battery tray, may not be exactly like the assembly line tray. Group 27 battery tray is typical for cars with air conditioning and higher amp alternators. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars.  Replaces Ford Part #: D0OZ-10732-B.

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Original used bracket, not reproduction. Replaces Ford Part #: D0OZ-10757-A.

Insulator for mounting the ammeter on any 1969-73 Mercury Cougar or Ford Mustang with factory ammeter in gauge cluster. Also used on other Ford cars with ammeter. Casting number C9ZF-10C914. Ford Part # C9ZZ-10C914-A

Visors are fully padded and covered with the correct vinyl or textured tier to match the headliner. Sold as a Pair.

Made from clear acrylic plastic with prisms added to increase the bulb brightness.Ford originally used white nylon with no prisms, which makes the light very dull. Replaces Ford Part # D1AZ-13783-B.

Core driver side (left hand) bucket seat with the side seat release lever for the Mercury Cougar or Ford Mustang. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket seat we can discard the upper portion. The...

Reproduction plastic seat backs for the 1971 Cougar or Mustang.Sold as a pair

Replaces Ford part #D1ZZ-6561692. Sold as a pair, available in black only. They can be painted but it is rather difficult to get paint to adhere long term. We have most colors available used, contact us for availability.

American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process.NOTE: These foam kits work well on the Standard and Decor interiors but you will find on the XR7 the lower portion does not work well.

Very nice reproduction knobs for 1971-73 Mercury Cougar and Ford Mustang with outboard mounted seat back releases. Also fits 1971 and newer Mercury Comet and Ford Maverick with bucket seats, as well as 1971 and newer Pinto. *Note - Not to be confused with the center mounted release knobs.

Very nice reproduction knobs for 1971 Mercury Cougar and Ford Mustang with center mounted seat back releases. Also fits 1971 Mercury Comet and Ford Maverick with bucket seats, as well as 1971 Pinto. *Note - Not to be confused with the outboard mounted release knobs.

Core passenger side (right hand) bucket seat with the side seat release lever for the Mercury Cougar or Ford Mustang. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket seat we can discard the upper portion. The price...

Grade B used passenger side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade B will have scuffs and or scratches, might also be chalky in a couple of places. Various Ford part numbers associated with this panel, here are a few: D12B-6260762, D3ZB-6561632, D1FZ-6260762, D2ZZ-6260762, and...

Grade A used driver side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade B will have scuffs and or scratches, might also be chalky in a couple of places. Various Ford part numbers associated with this panel, here are a few: D12B-6260763, D3ZB-6561633, D1FZ-6260763, D2ZZ-6260763, and...

Used RIGHT side bucket seat medium brown / ginger hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634. ...

Used RIGHT side bucket seat maroon hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used RIGHT side bucket seat dark green hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used RIGHT side bucket seat light green hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used RIGHT side bucket seat white hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used RIGHT side bucket seat dark blue hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used LEFT side bucket seat medium brown / ginger hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635. ...

Used LEFT side bucket seat black hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used LEFT side bucket seat dark green hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used LEFT side bucket seat light green hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used LEFT side bucket seat white hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used LEFT side bucket seat dark blue hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Not an exact replacement, but a decent replacement if you have a rear view mirror that the silver is peeling on. Includes new glue on mounting tab (bracket). Replaces Ford Part #: C8AZ-17700-A. This picture below shows the rear view mirror variations from 1967-1973. Check out this video ...

This special bracket gets glued to the windshield glass. Rear view mirror mounts on it. Plain finish. Replaces Ford Part #: C9AZ-17698-A.

These rear view mirror lenses are sold on an exchange basis.  Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens and send it in. Keep in mind glass is porous and is prone to staining. Often times these faint stains do not show up until the glass...

Rear seat bottom or lower cushion from any 1971 Mercury Cougar or Ford Mustang coupe or hard top only. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Only fits 1971 cars due to the seat belt location in the floor. 1972-73 seats are a bit narrower, due to the seat belt retractors in the side panels.Replaces Ford part number D1ZB-6563120.*Note - Excludes 1972-73 Mustang and Cougar.

Used RIGHT side bucket seat black hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used LEFT side bucket seat black hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used actuator for the seat back release on the 1971 - 1973 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

Hard to find New Old Recent Stock switch for the driver side power seat on the 71 - 73 Cougar or Mustang. Toggle switch looks accurate, however, you will need to reuse your original plugs. PLUGS NEED TO BE CHANGED FOR SPECIFIC APPLICATION. Some of the Ford part numbers include: D1WB-14B723-AA, D1WB-14B723-Ab, D2WB-14B723-AC, D1ZB-14B723-AA, D1ZZ-14A701-A, D2WY-14A701-A.

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these. Sold as a Pair. Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

This kit contains 500 hog rings, more than enough for two bucket seats and one bench seat.

These are often cracked or collapsed causing your seats to lean back too far. One kit does one seat, two kits required per car.*NOTE* Don't discard your original screws! The screws supplied with this kit have a head that is just slightly smaller than original so when you really tighten the screws down the head goes right on through the stop! A very small washer will cure the problem if you choose to use the screws supplied. Replaces Ford Parts #: C8ZZ-6560310 & C8ZZ-6560311

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang coupe or hard top. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-6566700.*Note - Does not fit convertible.

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

If your pump works fine but leaks this is an easy kit to install. Replaces Ford Part #: D1AZ-3B584-A.

Replaces Ford part # C7AZ-3A006-C or D1VY-3A006-A.