All Available Parts - 1970 Ford Mustang

[No Description Provided]

This used emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. Replaces Ford part # C6OZ-2A602-A.

This reproduction emergency / parking brake spring for the V8 Mercury Cougar or Ford Mustang is made from original Ford blue prints. This is the oblong spring that is painted YELLOW like the originals, rests upon the parking brake cross bar link between the shoes.These springs came from the factory in either Red or Yellow.You can find the Red spring here.Replaces Ford part # C2OZ-2601. ...

Premium grade reproduction driver side (left hand) rear emergency / parking brake cable. This is the short one, 31 inches, located on the driver side and is an exact fit for 1970 - 1973 Mercury Cougar and Ford Mustangs. Ford Part # D0ZZ-2A635-B

Reproduction concours correct premium grade passenger side (right hand) emergency / parking brake cable for the 1970-73 Mercury Cougar and Ford Mustang with V-8 engines. This is the long one on the passenger side (right hand) and measures approximately 133-1/8 inches long.

Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106. 

Driver side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1970-71 Mercury Cougar and Ford Mustang.

Passenger side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1970-71 Mercury Cougar and Ford Mustang.

Front emergency brake cable bracket that welds to the floor under the drivers side floor board.  It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted. Fits all 1969-70 Mercury Cougar and Ford Mustang.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Reproduction passenger (driver hand) side drum brake self adjuster repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Used emergency / parking brake pedal pad that features all stainless steel construction. This unit cleans up very well with fine steel wool, has reusable folding tabs, and is easy to install. A great piece to finish off your interior!Replaces Ford part # C9ZZ-2A487-C.

Reproduction emergency / parking brake pedal pad trim piece for the Mercury Cougar or Ford Mustang. This great little reproduction looks good and is one of the little detail pieces that can separate a nice car from a mint car.Replaces Ford part # C9ZZ-2A487-C.

Bolt for attaching the emergency brake Pedal Assembly. This is a 5/16-18 washer head bolt. Sold individually, Three bolts attach the E-brake assembly. Fits all 1969-70 Mercury Cougar and Ford Mustang.

Passenger side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog. Ford part # C8OZ-2B292-A Check out this video Check out our caliper tips and tricks video below: ...

Driver side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog. Ford Part Number C8OZ-2B293-A Check out this video Check out our caliper tips and tricks video below: ...

Stamped steel bracket that mounts on the rear of the calipers. These often fracture or rust out. We only sell the pristine units, two required per car, PS and DS are the same. Ford part # C8OZ-2B295-A Check out this video Check out our caliper tips and tricks video below: ...

Reproduction grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. Replaces Ford part # B5A-1131.

This is a front brake grease dust cap tool. No more dented caps. These are milled from 6061 solid aluminum.

Cork gasket for the disc brake splash shield. Fits all 1968-73 Mercury Cougar and Mustang and 1968-71 Ford mid size including Torino, Cyclone, Ranchero, Fairlane.Replaces Ford part number C8OZ-2B160-A.

New front outer wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.865 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

New front Inner wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.378 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models with a BOSS 302 engine:1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang ...

This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models with a BOSS 302 engine:1970 Cougar1970 Mustang

This is a reproduction of the original engine displacement decal Black on chrome background followed by black background with chrome Cougar logo and 302-4V High output lettering. Located on the top of the air cleaner. 1970 G code Eliminators likely only used the yellow Ford Boss 302 decal. Has anyone found an original 1970 Boss Eliminator with this decal? The CCOA would be very interested in that documentation. Fits the following models with a BOSS 302 engine: 1970 Cougar - (maybe) 1970...

Emissions decal for the 351 Cleveland 4 barrel with automatic or manual transmission on the 1970 Mercury Cougar and Ford Mustang manufactured after January 1, 1970. Printed with part number D0AE-9C485-AG.

Emission decal for the 351 Cleveland 4 barrel with an automatic transmission in the 1970 Mercury Cougar or 1970 Ford Mustang manufactured before January 1, 1970.  Printed with part number D0AE-9C485-F.

Exhaust Emission Control decal for the BOSS 302 with a manual transmission in the 1970 Mercury Cougar and Ford Mustang manufactured before January 1, 1970. Printed with part number D0ZE-9C485-B.

Emission Decal for the 428 4 barrel with an automatic or manual transmission in the 1970 Mercury Cougar and Ford Mustang. Printed with part number D0OE-9C485-J.

Emission Decal for the 351 Cleveland 2 Barrel with an automatic or manual transmission in the 1970 Mercury Cougar or Ford Mustang. Printed with part number D0AE-9C485-AH.

Reproduction California Emission Control Caution Decal for the 1970 Mercury Cougar / Ford Mustang

There are multiple emissions decals available for the 351 Cleveland 2 barrel with an automatic or manual transmission in 1970 for the Mercury Cougar and Ford Mustang.  This sticker is printed with part number D0AE-9C485-A.

Exhaust Emission Control decal for the BOSS 302 with a manual transmission in the 1970 Mercury Cougar and Ford Mustang manufactured after January 1, 1970. Printed with part number D0ZE-9C485-F.

Reproduction Boss 302 California Emission Decal for the 1970 Mercury Cougar / Ford Mustang

There are multiple emissions decals available for the 351 Cleveland 2 barrel with an automatic transmission in 1970 for the Mercury Cougar or Ford Mustang. This sticker is printed with part number D0AE-9G485-S.

California emission control "Caution" decal for the 1970 Mercury Cougar and Ford Mustang.

Engine code decal for the 351 Cleveland with a 2 barrel carborator on the 1970 Mercury Cougar and Ford Mustang manufactured after January 1, 1070. Printed with L 10° K834 K.

Engine Code Decal for the BOSS 302 with a Drag Pac on the 1970 Mercury Cougar and 1970 Ford Mustang. Printed with L 16° 300S.

Engine Code Decal for the 302 with automatic transmission and air conditioning on the 1970 Ford Mustang. Printed with L 6° K272AG.

Engine Code Decal for the 302 with a automatic transmission on the 1970 Ford Mustang.  Printed with L 6° K280A.

Engine Code Decal for the 302 with a manual transmission on the 1970 Ford Mustang. Printed with L 6° K279A.

Engine Code Decal for the Boss 302 without the Drag Pac option on the 1970 Mercury Cougar and 1970 Ford Mustang. Printed with L 16° 299 D.

This decal goes on the tire jack itself.

Replace FORD Part #: C8WB-17093-B

Reproduction Space Save Tire Instructions Decal for the 1968 - 1973 Mercury Cougar / Ford MustangThis yellow sticker actually came out in 1971-ish. These were sent to previous owners of cars with space saver tires, with instructions to apply sticker to the space saver rim. We believe that they were factory installed with B.F. Goodrich space saver tires starting in 1971 for safety reasons. 

Replaces Ford Part #: C8WB-17093-D.

Reproduction Space Saver Spare Recall Postcard for the 1968 - 1971 Mercury Cougar / Ford Mustang

Correct for the 1969 Eliminator SS wheel. Replaces Ford Part #: C9WB-17093-B

Notice the line drawing of a Mustang and the decal has a Cougar part number. More times than not I see the exact decal with a Mustang part number for 1969. Replaces Ford Part #: C9WB-17093-D.

Replaces Ford Part # D0ZA-A

Replacement sleeve to put onto your original tire inflator bottle. Correct style for 1969-70 Mercury Cougar and Ford Mustang. Specifically for the 7.35-14 space saver tire installed optionally in Cougars and Mustangs. Correct Ford part number C9WA-19F514-A imprinted on the decal as shown.

Reproduction Detroit Locker Glove Box Decal for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar

Reproduction Decal Set / Under Hood Paint OK for the 1969 - 1971 Mercury Cougar or 1971 Ford Mustang 

 Reproduction BOSS 302 Valve Cover Decal for the 1969 - 1970 Mercury Cougar or Ford Mustang

Automatic chokes had been the norm for many years so a notice to the operator was a must. Decal Text:NOTICEThis vehicle is equipped with a manual choke located immediately below the ignition switch. For proper starting use manual choke. ...

Reproduction Convertible Top Utica Plant Decal for the 1970 - 1973 Mercury Cougar or Ford Mustang 

Reproduction Ignition Lock Sun Visor Instruction Sleeve Decal for the 1970 Mercury Cougar or Ford Mustang 

Reproduction BOSS 302 Rev Limiter Decal for the 1970 Mercury Cougar or 1970 Ford Mustang 

Replaces Ford Part #: D0ZF-12450-A

Reproduction of the firewall vacuum tree decal that is affixed to six port plastic vacuum tree that is located in the middle of the firewall, just below the horizontal body seam.Ford Part # D0OZ-9C490-C

This is an accurate reproduction of the tie down notice decal that was placed on the rear license plate frame. This was to remind dealers to remove the tie down plates that were used to secure the cars to the transport trains / trucks on their way from the factory to the dealers. Ford wanted to recycle these plates to save money, but dealers often didn't feel it was worth their time to remove the plates. Thus, many cars still have them. Check yours out! ...

Holley fuel filter decal, for Holley equipped cars. Including all 1967-68 S code 390-4V, 1968-70 R and Q code 428 Cobra Jets, 1967 GT-E with W code 427-4V, or 1969-70 G code Boss 302 Eliminators. Concours detail item. C7OE-9155-A. 

Controversy abounds on which shrouds received these and which did not. It is our understanding that no early Cougars came from the factory with this decal installed. This decal first surfaced when Ford had major problems with their flex fans in the early 1970's. We will let you decide if it is correct for your application... This is placed on the top, center of the fan shroud.

Ignition coil silver decal stamped with:FAC-12029-A12 VOLTS AUTOLITE OLECUSE WITH EXTERNAL RESISTOR

Reproduction Autolite Fl - 1 Oil Filter Decal for the 1967 - 1972 Mercury Cougar or Ford Mustang 

Reproduction 60000 Mile 6 Month Lube Sticker for the 1967 - 1973 Mercury Cougar / Ford Mustang

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.

This decal can be used to overlay your replacement oil filter, so it looks more like a vintage original oil filter. Research indicates that the gold was primarily used on 66 and earlier, as was the red. They then phased the red/gold out and replaced it with the white oil filter printed with the Autolite logo.   1967 Cougar/Mustang could have come factory installed with either red or gold. 1967 - 1969 factory serviced cars could have gotten the red or gold until stock was...

Set of 5 reproduction firewall inspection decals. During final inspection, these decals where placed in different locations on the firewall / cowl area and one P decal between the weatherstrip and dash pad inside the drivers door jam. This decal set has the assembly line inspectors names stamped on them. These decals would have been used on cars equipped with Boss 302 and BOSS 429 engines.

Reproduction oil cap decal for the Ford 1965-67 oil caps. 

Decal Text: Autolite EV-50 C6AZ-6A666-B Replaces Ford Part #: C6AZ-6A666-B.

Reproduction PCV Plastic Ring for the 1970 and 1971 Mercury Cougar or 1970 - 1971 Ford Mustang with the 429 Cobra Jet or 429 Super Cobra Jet. Decal Text: AutoliteEV-48C9TZ-6A666-A Replaces Ford Part #: C9TZ-6A666-A.

Decal Text: Autolite EV-50 D0AZ-6A666-A Replaces Ford Part #: D0AZ-6A666-A.

Replaces Ford Part #: EV-51 or D0OZ-6A666-A

This is what I consider to be "Premium Quality". Very correct in every detail and made in the US! The group 27 larger tray was optional on any Cougar and standard on big block Cougars. Replaces Ford part # C9ZZ-10732-AR

Perfect fit the first time. You will be happy with this Group 24, quality reproduction and check out the price! These battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Replaces Ford part #: C7ZZ-10732-D.

Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang

Fits Standard and XR7

This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A

Kit comes complete with J bolts and mounting nuts. Replaces Ford Part #: D0AZ-10756-K.

Reproduction plastic battery hold down for the Mercury Cougar or Ford Mustang. According to the Master Parts Catalog, late 1969 through mid 1970, Cougars and Mustangs used these black plastic units. Late 1970 used the same as the 1971-73 model.Replaces Ford part # D0DZ-10718-A.

Concourse Correct with 22, 24 & 27 series batteries for Mustang, Cougar and Shelby GT350/500 made in the USA to original Ford Specifications, includes attaching bolts. Replaces Ford Part # C9ZZ-16060-A or C9ZZ-16052-P .

This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.

This is a replica of the warning tag that came on positive (+) terminal of Autolite batteries when the 1967 - 1972 Cougars and Mustangs were shipped from the factory.

This was an instruction tag for the customer on how the Rim-Blow horn functioned. It would have been hanging from the steering wheel when the car was new. See product images for factory placement example.Replaces Ford Part #: C9ZF-13A875-AA

Replica of the coil spring shipping tag that would have been found on factory delivered 1967 - 1973 Cougars and Mustangs.

Replica antifreeze tag that would have been found on the 1970 - 1973 Cougars and Mustangs when they shipped from the factory. See the product images for an example of factory placement.

Reproduction Small Block Engine I.D. Bolt for the  1967 - 1973 Mercury Cougar / 1967 - 1973 Ford MustangSold individually 

A/C compressor clutch decal for Mercury Cougar and Ford Mustang.Replaces Ford Part #: C7AA-2987-D.

Here is our A/C dryer decal for your Coug or Stang equipped with A/C. Replaces Ford part #: D0AA-19959-C3.

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. For any 1970-71 Mercury Cougar or Ford Mustang with 302 or 351 engine and 43-55 AMP alternators. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces...

Good used group 24 tray for 1968-70 Mercury Cougar or Ford Mustang. Assembly line installed group 24 battery tray, for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting).

Reproduction group 27 battery heat shield that fits many Mercury Cougar and Ford Mustang applications from 1967-70, on most hi-performance engines. It was often the first part discarded but serves a real purpose. Nice American made part, stamped with Ford numbers C7ZB10A682B and C7OB10A682B. There is also a D0... sized for group 24 heat shield offered for 1970-73. *Trivia - these battery heat shields were often trimmed down to fit group 24 batteries.Click on the link below to find some...

Used plastic battery hold down for the Mercury Cougar or Ford Mustang. According to the Master Parts Catalog, late 1969 through mid 1970, Cougars and Mustangs used these black plastic units. Probably introduced at the same time in very late 1969 as when the hold down clip was used to attach to the battery apron? Replaces Ford part # D0DZ-10718-A and casting number D0DB-10755-A. 

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Key reminder buzzer for 1970-71 Mercury Cougar and Ford Mustang. Also used on 1970-72 Lincoln MKIII and Thunderbird. Can also be stamped DOAB-13150-B, DOAB-13150-E, and DOAB-13150-F. Ford master part number D0AZ-13150-E. All buzzers are bench tested prior to shipping.NOTE: This buzzer is for ignition key reminder with two posts. The four post ignition / headlight buzzer can be found here.Click on images to enlarge. ...

C8OZ-14A068-GRADEB Black Bake-O-Lite original fuse block. Grade B, not broken, but will have chips from prying out fuses. Perfect for upgrading your broken fuse block that has a nice wiring harness. 69 70 71 72 Mercury Cougar Ford Mustang fuse panel. Sometime in the later part of 1972 Ford switched to a nearly identical brown fuse block.

C8OZ-14A068-A Black Bake-O-Lite original fuse block. Grade A, no cracks or chips. Perfect for upgrading your broken fuse block that has a nice wiring harness. 69 70 Mercury Cougar Ford Mustang fuse panel. Sometime in the later part of 1972 Ford switched to a nearly identical brown fuse block.