Body

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver and passenger side upper only. Fits any 1967 Mercury Cougar and Ford Mustang.Ford part number 6502666.

Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C5ZZ-6512118-A.

Reproduction radiator / core support for Mercury Cougar and Ford Mustang. This is the very best one made! Replaces Ford part # C7ZZ-16138-B and C7ZZ-6510852-B together.

Used trunk or luggage compartment latch, fits all 1967-73 Mercury Cougar and many other Ford and Mercury cars. Comes with 3 bolts for mounting.Replaces Ford part number C5AZ-6243200-A.

Reproduction driver side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps ...

Reproduction passenger side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps. ...

Reproduction driver side rear inner apron for both the Mercury Cougar and Ford Mustang.

Reproduction passenger side rear apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

This area of the door often cracks due to the stress caused by worn out hinges. This twelve piece kit includes six screws and six form fitting washers to reinforce the recessed areas that often crack. If your latch area is badly cracked you will want to purchase the repair kit that requires being welded in.

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

High quality chrome finish on lever & base. Improved cable for smooth operation. You must have correct trunk latch to use this remote. Detailed instructions included. Look for the trunk latch in our 'related items' tab.

This is an upgrade to the Electronic Trunk Release. Allows trunk to be opened with just the push of a button on two wireless remotes that are included. NOTE: This item requires that you have a latch mechanism equipped with the remote release tab.

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Used, with little to no scratches, suitable for every day driver.

Used, with scratches and pits, suitable for every day driver or restoring.

Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.

Reproduction hood latch return spring, attached to the sides of the hood latch on the 67 - 68 Cougar. These reproductions are smaller than the originals, but it seems these are the only replacements available at the moment. Sold individually, 2 required for Cougar, 1 for Mustang.

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

This is the nylon roller that fits on the end of the window regulator arms. Includes rivet.Sold individually. 2 rollers required per window, 4 rollers required per car.Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" DiameterHere's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction roof brace for the 67 - 68 Cougar or Mustang. This is the leading front support on your roof, directly above your windshield.

These were installed only on early production 1967 Cougars but can be installed on any 1967 Cougar. Later in the year they quit installing these and just used a rubber plug to fill the hole. 1968 was not drilled for these. Sold as a pair.

New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily. *NOTE* This item can only be shipped via UPS ground. No Foreign orders please. Check out this video ...

Good grade A used jack with correct fine threads. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not. Grade A will not have rust or damage.

Good used jack with correct fine threads. Notice the remnants of the original jack instruction decal. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not.Grade B will have Rust and or the top portion letter "M" fitting may be damaged.

Concours? Well almost... These are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Sold individually, three per side, six per car required. These often get destroyed when you go to replace your door window regulator slides. Three of these are used to install the C7ZZ-6523288-A track. Stainless steel.Thread size: 8/32 Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) Not sure where to begin when it comes to replacing your window regulator?...

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

Fits all Mustangs

These reproduction fender shield to bumper screws fit bot the standard and XR7.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Excellent reproduction seals for your 67 - 68 Cougar or Mustang vent windows. Made from Ford's Original Tooling. Much better fit than other reproductions. Replaces For part numbers:C7ZZ-6521449-AC7ZZ-6521448-A

Seals between chrome vent frames and door on exterior side. Stops water from leaking between vent window and door. Keep in mind that this seal comes as one strip and it meant to be cut down the middle.Sold as a pair.Replaces Ford part #: C6OZ-6322280 or C6OZ-63222A80-A.

These high quality vent window seals are the first on the market to replace the original Ford part exactly. This is the small seal at the front of the door and next to the door weatherstrip. Sold as a pair. Replaces Ford Part #:C7ZZ-6522332/3

Premium reproduction rubber seal with the proper thickness of the 1967-68 seal as found on Mercury Cougar and Ford Mustang except these are not molded to the extension contours. Starting in 1969 this channel seal was manufactured slightly smaller which tightened up the gap on the fender and quarter extension seals. This seal maintains the slightly larger gaps. Sold as a pair, two pairs needed per car.  Each package has 2 strips of 25 1/2" lengths. *NOTE* Do not over tighten the...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

This seat riser / platform is specific to Mustang, but if you're "vertically challenged"....you may want to go ahead and use this part on your Cougar. It'll raise your seat up enough so that you don't have to use phone books anymore!

This seat riser / platform is specific to Mustang, but if you're "vertically challenged"....you may want to go ahead and use this part on your Cougar. It'll raise your seat up enough so that you don't have to use phone books anymore!

Used cut from our wrecking yard, rear shock support for the 1967-70 Mercury Cougar and 1965-70 Ford Mustang hard tops. This support sits underneath the transition hump and attaches the upper mounts of each rear shock. The shock hardware is accessible through two access holes on the hump. Body plate may be slightly different through the years. Cut will be very much like shown. Frame rail segment, and spot welds to be removed on your end. Various Ford part numbers in the book for single or...

If you buy this reproduction tower, you will no doubt save you time in clean up. But nothing will ever fit and look like original FoMoCo towers!Here's a little film to help you fortify your flexxy feline!

Excellent condition tower as cut from a Western parts car. No specific part number for this structural front suspension section.Generic Ford part # C7ZZ-16055-D or E, includes apron and side member.Here's a little film to help you fortify your flexxy feline! ...