1967 Ford Mustang

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. Listed in the...

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Used coil mounting bracket. This is the Big Block V-8 version starting 1967-69. Found on 390 and 428CJ cars. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. This version is for big block V-8's, and has an additional 'C" channel bracket on the bottom, later versions had an removed thel reinforcing 'C' channel on the bottom. Later version...

Used coil mounting bracket. This version of the bracket is probably the most common. Typically this version was used on small block V-8's in 1967-68. This version has the 'rails' to give it strength. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to...

Used coil mounting bracket. This is the later Big Block V-8 version starting 1969. Found on 390 and 428CJ cars.We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. This version is for big block V-8's, and has a 'flat' strap on the bottom, earlier versions had an additional reinforcing 'C' channel on the bottom. Probably used starting in 1969. Some have...

We will loan this coil spring compressor for 60 days, with a 100% refundable purchase price. This tool now comes with a bearing to make the job much easier. Only available to customers that purchase our front suspension rebuild kits. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Coil spring compressing tool, this is a must for safely removing front coil springs on any 1967-73...

New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...

Used driver side coil spring cover, taken from a parts car. Ford part # C7ZZ-3383-A.

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.

Made from soft flexible rubber very similar to the OEM material. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. If you prefer polyurethane insulators, you can find them here. Replaces Ford Part #: C4DZ-5415-A.

Features quality stamped steel construction, bushings, nuts, anti-squeak coil protector pads. From the get go these were never a very good design... The rubber is prone to cracking and the unit will bind under severe use. Not just speaking of the unit we are offering but all of them including the original Ford units. Here is an interesting article for those that are not happy with status quo. Global West and others have come up with their own solutions and after we have spent more time testing...

High Performance Coil Spring Perches offer a very affordable upgrade to stock spring perches with rubber bushings. These are made with synthetic elastomer bushings which are similar to polyurethane in performance and longevity, but will not squeak like polyurethane. The perch can rotate 360 degrees on the shaft, which allows the front suspension to articulate freely. This feature also eases the installation of the coil spring. Zerk grease fittings are installed and locking nuts are included....

Replica of the coil spring shipping tag that would have been found on factory delivered 1967 - 1973 Cougars and Mustangs.

These Linear springs are custom wound for the performance-oriented customer. These feature 600-pound/inch rating and will lower the car approximately one inch from stock. Painted black, sold as a pair. Note: If you look close at factory sales pictures from the day you will notice the cars sit about 1" lower in back than front. These springs will level the car out provided your rear leaf springs are not sagging.  Linear springs are the easiest to understand. When you think of a spring,...

One year only part not found on any other car except Cougar and Mustang with tilt. If you would like to run a 1968 or newer steering wheel on your 1967 then you need to exchange this cover with the version found on the 1967 Thunderbird which has no lip at the top. We have these in stock and would enthusiastically trade it for the Cougar / Mustang upper cover. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This Thunderbird collar is a good substitute for those wanting to put an after-market or 1968 up steering wheel on their 1967 Cougar / Mustang. We also suggest purchasing this collar when installing our reproduction 1967 Mustang deluxe steering wheel.  *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Complete reproduction front drum brake spring kit for Ford Mustangs equipped with 9" drums. This kit contains all the replacement springs and hold downs required to do a professional brake job on front drum brakes. Kit includes enough parts for two wheels.

* This is the closest available fit full floor pan for the 1969-73 Ford Mustang Convertible or Mercury Cougar Convertible, this pan will need modification to "make it fit." Complete floor pan for the 1969 - 72 Mercury Cougar or 1965-68* Ford Mustang Convertible. This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes substantially....

Complete floor pan for the 1965-68 Ford Mustang. NOTE: Can be made to fit 67-78 Cougar, Included seat risers are Mustang versions, which are taller than the Cougar seat risers. We recommend re-using your original Cougar seat risers, unless you want the extra height of the Mustang risers. Also note that the risers included with this floor pan will not be attached, you'll have to weld them on. Keep in mind Cougar has a longer wheel base which make the portion under the back seat substantially...

This is a complete set of four used headlight bulbs, marked with the FoMoCo logo. These sets come with two high beam and two low beam bulbs. Each bulb is tested by the electrical department. If you're trying to keep your Cougar or Mustang as close to original as possible, you should definitely grab a set.These bulbs are date coded, so if you want a particular date, be sure to mention it in the comments section of your order.  

This complete four piece kit is for any small block 289, 302, or 351 Windsor Cougar 1967, 1968 and 1969. 

This complete four part kit is correct for any 1967-68 small block 289 or 302, and 351 Windsor Mercury Cougar or Ford anything 1967, 1968 and 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut.If you do not have a air conditioning you will need a spacer in place of the round spacer shown. If you have the 351 Windsor without A/C, you will need a the rectangular spacer which is sold separately.

This complete four part kit is correct for any 1969 small block 351 Windsor Mercury Cougar or Ford anything 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut. If you do not have a air conditioning you will need a the rectangular spacer which is sold separately.

This unit is for Mercury Cougars and Ford Mustangs, is pre-assembled, and includes the drier and all brackets.

Reproduction Console Ashtray Bumper for the 1967 Mercury Cougar or Ford Mustang.

New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.

Reproduction aluminum shift indicator console overlay for the Mercury Cougar or Ford Mustang. Although a brushed finish is correct, this reproduction has a coarser brush stroke when compared to the originals and is a bit dull.  We recommend a quick polish to make them look closer to the finish of the originals. These fit well, and unless you put them up against an original, it is hard to tell the finish is slightly different. This installs around your console...

A needed part for giving your car a tune-up.

A needed part for giving your car a tune-up.

New midland control hub assembly and disassembly tool for use with the 67 - 69 Cougar and Mustang Midland style booster

This unit was used only one year on the Cougar and is unique because of its smaller fitting (1/4") for the pressure hose. Many 1967 Cougars have been converted to the 1968 valve over the years so you may want to double check your valve before ordering. We highly recommend upgrading to the large nut (5/16") control valve as the small nut control valve posses a potential safety issue, thus the reason why Ford replaced it the following year. The small nut system was engineered dangerously close...

Reproduction tack strip for the rear bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the rear bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 Feet (60 inches) of material and will have to trim to fit your top. You can also...

C6AE-E Multiple applications over the years. 1. Later 1967 production cooling fan, generally used after 11/14/1966 on most 289 engine applications. 2. 1968 302 without air conditioning. 3. Mid year (after 11/6/1968) 1969 351 without air conditioning. 4. 1969 Early Boss 302 before 4/14/1969. 5. 1971 Cougar with 351 engine, without air conditioning. 6. **1973 Cougar 351-2V without air conditioning prior to 2/19/1973. Fan description - 4 blades and 17-1/2 inches in diameter. Ford master part...

C6OE-G Clutch style 7 blade cooling fan for all 1967 Cougars with 289 engines with factory installed air conditioning. Additionally, 1968 302 engines with factory air conditioning (Cougar and Shelby GT-350 only). Fan description - 7 blades and 17-1/2 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C4OZ-8600-D. Original fan drive clutch cast number for this application is C7ZE-B. NOTE! If you have the fan shown here and would like to upgrade to our FE / Big...

Reproduction transmission cooling lines for the Mercury Cougar or Ford Mustang equipped with the C-4 automatic transmission. These lines are sold in pairs.

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang produced from 1967 through early 1968 that came equipped with the C-6 automatic transmission and 390 engine. These lines are also available in stainless steel and are sold in pairs.

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

Reproduction under dash light assembly for the 67 - 68 Cougar or 65 - 68 Mustang. This short style assembly was used on either driver or passenger side. There were two versions of this light, a long bracket version and a short bracket version. The driver side was always the same, but the passenger side typically used the longer version on cars with no A/C. Cars that had air conditioning used the shorter bracket style to keep from coming in contact with the A/C plenum. ...

Used pivot cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

Sold individually Zinc Dichromate (yellow-rainbow)

Clear plastic cowl seals for all 1967-68 Mercury Cougar and Ford Mustang. These are supposed to prevent rain or water from entering your cowl vents in front of the windshield. These were created to help prevent water from dripping on your floor from leaking cowls. These fit fairly well, but you need to check all of the corners when installing. We feel that they are a little under sized to properly seal those cowls easily. Our first attempt left one of the corners with a gap, thereby allowing...

Get ready for some serious labor if your car needs this complete panel!

This kit is good for cowls with moderate to minimal rust. Easy to install on the driver side, but takes more effort on the passenger side especially if you have A/C. Another way to avoid doing expensive cowl repairs is to purchase our cowl cover.