1967 Ford Mustang

Used heater blower motor for 1967 Mercury Cougars and Ford Mustangs with integral or factory air conditioning. The tell tale sign is the early motors have a nipple of attaching the rubber elbow. Later version has a round hole for attaching a different rubber elbow. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is also included. On...

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Reproduction heater blower motor for Mercury Cougar and Ford Mustang that is a high quality replacement part at a reasonable price. However, these off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the...

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"

New rubber body plug, fits 1-3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Typical application is rear leaf spring access.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377356.

New rubber body plug, fits 1-1/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some of the holes include: inner frame rails at radiator, center of firewall, and side of cowl.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377936.

New rubber body plug, fits 3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: frame rails at sway bar, rear floor pan, LH fender apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377977.

New rubber body plug, fits 9/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles, typically they are for: front fender aprons, transmission cross member, and radiator support. Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 376966.

New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-5/16" oval holes. Sold individually, Usually 2 per car. Fits 1967-70 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378923-S.

New rubber body plug, fits 13/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: trunk floor pan, side of cowl at door, and LH apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377949.

New rubber body plug, oval , fits inner frame rails. 3/4" x 1" oval holes. Sold individually, Usually 2 per car. Fits 1967-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378770-S.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...

Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.

Reproduction 289 - 302 Alternator Bolt w- Smog for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold individually 

 Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!

Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!

Coil bracket mounting bolt for all V-8 engines as found in 1967-73 Mercury Cougar and Ford Mustang. This3/8-16 bolt attaches the coil bracket to various places on the engines. Either on the intake manifold or the cylinder head. Will fit stock Ford cast iron intakes as found 1967-73. AMK bolt B-13722.

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.

Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

part # 382101-S2 Sold individually

part# 372434-SSold Individually.Head size: 5/8"Thread size: 7/16"

Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.

part # C1AE-6065-A. Longer of two. Sold individually

part # C1AE-6065-C. Shorter of two. Sold individually

Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.

Bolt with toothed washer for attaching 1967-68 Mercury Cougar and Ford Mustang door window parts. Both of the door window rear stops

Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).

Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351. Sold individually

Concours bolt for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. Sold individually, or in a set of 4. 1/2 inch hex head size an the threads are 5/16-24. This bolt is approximately 7/8" to the shoulder and 1-1/8" in total length.  Replaces Ford part # 380288-S. ...

Not a concours correct head pattern, but it looks good. Bright cadmium finish. 5/16-18 x 7/8 long.

Replaces Ford part # 385664-S

Replaces Ford part #375381-S Phosphate & Oil Finish

part # 379068-SSold individually

Used front crossmember bolt for the Mercury Cougar or Ford Mustang. It is crucial that you use this correct tapered bolt when installing the front cross member.

Reproduction zinc front shock bolt with correct anchor symbol on the head, just like the originals.Sold individually.

Front U clamp sway bar bracket bolt, for any 1967-68 Mercury Cougar or Ford Mustang. 3/8-16 x 1.0 Grade 5 bolt. Sold individually, 4 per car. part #20408-S

part# 20352-S Sold individually

Reproduction intake manifold bolt for the Mercury Cougar or Ford Mustang equipped with either the 390 or 428 engine. These little units are sold individually. 3/8"-16 X 2 5/8" Grade 8 Phosphorus Bolt Ford part # 43011-S

Reproduction caliper bolt from AMK Grade 8 hex bolt. 2 bolts per caliper, sold individually. 7/16-14 x 1-5/8". These bolts hold the two halves together on the four piston Kelsey-Hayes calipers. Fits Kelsey-Hayes installed, 4 piston disc brake calipers used by Ford 1966-67.Replaces Ford part # 378225-S.

Plain head, fine thread. Not concours, but meets or exceeds original specs. Sold individually.Ford part # 380328-S.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used to mount the vacuum actuator to the column in 1967 and the actuator to the bracket on 68-69. Also used to mount the steering column relay and vacuum release valve in 1968-69.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last...

Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S

Sold individually, pivot stud for the aluminum power steering pump mounting bracket. fits all applications for small or big block.  Also used on the 1970 Mercury Cougar with 428CJ. Phosphate & Oil (gray-black)

replaces Ford part # B-12764