Home > 1968 Mercury Cougar
All Available Parts - 1968 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 401-500 of 5414
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 13060 -
Rear axle vent bolt for the 67 - 73 Cougar or Mustang. This bolt serves a dual purpose, as it also holds the brake line bracket in place on the axle tube.
Availability: Used / Wrecking Yard Item
Item #: 30048 -
Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.
Availability: In-Stock Item
Item #: 31554 -
Nuts and washers for attaching the rear differential carrier or pumkin or third member to the rear axle housing.Correct for all 1967-68 Mercury Cougar and 1965-68 Ford Mustang. 8 inch or 9 inch third members, all the same.
Availability: In-Stock Item
Item #: 31656 -
New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.
Availability: Used / Wrecking Yard Item
Item #: 32081 -
Passenger side chassis bumper bracket for the rear axle. Passenger side as removed from a 1967-73 Mercury Cougar. Good condition bracket, road tested, but not salt road tested. Ships as shown, cut with generous margins around the original bracket.
Availability: Used / Wrecking Yard Item
Item #: 32080 -
Driver side chassis bumper bracket for the rear axle. Passenger side as removed from a 1967-73 Mercury Cougar. Good condition bracket, road tested, but not salt road tested. Ships as shown, cut with generous margins around the original bracket.
Availability: Rare / NOS Part
Item #: 26719 -
Ford original eye let bushing 100% correct for the 67-69 Cougar without competition handling, but will fit on any 67-73 cat including those with competition handling. Ford Part #: C4DZ-5781-C.
Availability: In-Stock Item
Item #: 41430 -
Reproduction anti-squeak pad for the leaf springs found on the Mercury Cougar or Ford Mustang. This little unit goes between each individual leaf spring and prevents metal to metal contact. These are sold individually and eight are required per car. Our reproduction leaf springs come with this pad pre-installed. Replaces Ford part # C0AA-5586.
Availability: In-Stock Item
Item #: 41270 -
This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD INDIVIDUALLY. Replaces Ford Part #: KC-55490-A.
Availability: In-Stock Item
Item #: 13929 -
This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD AS SET OF 8. Replaces Ford Part #: KC-55490-A.
Availability: In-Stock Item
Item #: 18990 -
Correct leaf spring eye bushing bolts for the 1968 - 1973 Mercury Cougar. 5" in length. Set includes 2 bolts and 2 nuts. Replaces Ford Part #: C7ZZ-5781-A.
Availability: In-Stock Item
Item #: 26749 -
This eyelet bushing is made from higher grade rubber and unlike the NOS and other reproductions has a solid center shaft. The center shaft of this reproduction is a flat piece of steel that is bent into a circle to make the shaft for the eyelet bolt to go through, just like NOS. Two per car, these are used on one end of the leaf springs and the shackles are used at the other end. Replaces Ford Part #: C7WY-5781-A, C4DZ-5781-C, C5ZZ-5781-A, D3ZZ-5781-B. ...
Availability: In-Stock Item
Item #: 18987 -
Poly eyelet bushing that will fit any 1967 through 1973 Mercury Cougar. Replaces Ford Part #: C4DZ-5781-C.
Availability: Used / Wrecking Yard Item
Item #: 24631 -
This would be for the non-competition suspension Cougars. U-Bolt length 6-3/4 inches, and threads 1-1/4 inch in length. U-Bolts include two (2) correct style attaching nuts. Competition suspension U-Bolts run about 7 inches in length. Ford part number C7WY-5705-A for Competition Handling option.
Availability: In-Stock Item
Item #: 26720 -
Leaf Spring U Bolt for the 1967 - 1973 Mercury Cougars with isolators. Will work on any 67-73 Cougar. Does not feature flattened area at top like original. Includes 1 'U' bolt and 2 nuts. 4 total U-bolts needed per car. *Note - For use with Cougar shock plate, angled wedge, rubber isolators and retainer boxes. Inside Height: 6-3/4"Inside width: 2 7/8" (Same as axle tubes) Replaces Ford Part #: C7WY-5705-A. ...
Availability: Used / Wrecking Yard Item
Item #: 30652 -
D0OZ-4204-9A300 1968-1973 9 Inch Third Member - UsedAlso called a pumpkin, 3.25:1 open ratio. These 3rd members will have the fill plug and 28 splined axles.Check your door tag under "Axle".
Availability: In-Stock Item
Item #: 30783 -
Concours rear axle vent hose for any 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Rubber hose that attaches to the metal nipple on the top of your rear axle housing. Fits 8 and 9 inch rear ends. Includes hardware as shown. Crimp clamp, screw clamp and bolt. Ribbed hose like original, and has yellow paint mark like from the factory. About 20 inches of hose is included, a little more than what was from the factory. Part number 4A001 in the chassis assembly manual.
Availability: Used / Wrecking Yard Item
Item #: 24269 -
NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Axles used: Passenger side - 31-1/8 inches long, Driver side 27 inches long. Complete rear end housing - drum to drum, with axles, and with pumpkin. For...
Availability: Used / Wrecking Yard Item
Item #: 24271 -
Bare housing with proper axle pad spacing for all 1967-1968 Cougars with 289 or 302 engines. Over-sized shipping length. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. This axle housing was used starting about mid 1967. It does not have the fill plug in the rear of the housing. * Important - Please check your car to verify that your 8 inch third member has a fill plug. Replaces Ford part number C7ZZ-4010-E. ...
Availability: Used / Wrecking Yard Item
Item #: 21607 -
Used rear leaf spring retainer for 1968 -73 Mercury Cougar with standard or non-GT / non- competition handling suspensions. Additionally it fits most 1966-70 Mercury Comet / Montego, 1970-71 Ford Torino. Identified with a stamped number "6" on the top. The inside height is 1-3/4 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be some erosion due to...
Availability: Ships Direct from Supplier (Except International)
Item #: 14408 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14410 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14413 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14414 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14415 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14419 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14420 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14421 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14422 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14424 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14425 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14429 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14430 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14431 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14435 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14436 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14437 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14438 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14448 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14449 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14460 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14461 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14462 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14464 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14465 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14486 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14487 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14497 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14498 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14499 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14500 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14501 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14502 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 14488 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 10192 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: In-Stock Item
Item #: 11294 -
Reproduction rubber dust seal or boot with steel reinforcing ring for front suspension inner and outer tie rod ends. 1967-69 Mercury Cougar, Ford Mustang, and many other Ford cars. This is the concours version with Ford casting number C6OA-3332-A.*Note - This fits the early tie rod ends. If you have changed to later model disc brake spindles or the Granada conversion, we don't have an option for that.*Note - Excludes 1969 Boss 302 cars and some 1969 Shelby GT500 Mustangs.Replaces Ford part #...
Availability: In-Stock Item
Item #: 13373 -
It took a long time but our supplier finally got this bushing right. They ended up copying a never installed production original bushing Ed Meyer acquired from the Kar Kraft factory back in the day. All details have been copied including the two small ribbed lines located on one side. NOS Bushing notes: If you have NOS C9ZZ-5493-A front sway bar bushings in a Ford bag good luck making them fit. Yes, its a documented fact that almost all NOS 15/16" sway bar bushing Ford sold in a bag are too...
Availability: In-Stock Item
Item #: 26732 -
Standard size front sway bar bushings were 3/4 inch from 1967 - 1970. Rubber construction, sold in pairs only. Replaces Ford Part #: C7OZ-5493-C or C6OZ-5493-B.
Availability: In-Stock Item
Item #: 26733 -
Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-E
Availability: In-Stock Item
Item #: 26734 -
Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-J.
Availability: Used / Wrecking Yard Item
Item #: 24180 -
Used front sway bar, does not include any mounting brackets or end link kits. Ford part # C7WY-5482-A.
Availability: In-Stock Item
Item #: 26727 -
Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.
Availability: Used / Wrecking Yard Item
Item #: 23952 -
Pair of U-shaped brackets that mounts the long flat part of the front sway bar to the chassis. Two needed for attaching front sway bars. *Note* 1969 and 1970 Cougars with the Competition Handling Package which included all with 428CJ and Boss 302 engine packages, used a different bracket with a Ford part number of C7ZZ-5486-A.Replaces Ford part number #: C6OZ-5486-B.
Availability: Out of Stock
Item #: 24274 -
U-shaped bracket that mounts the long flat part of the front sway bar to the chassis. Clamps sold individually, two needed for attaching front sway bars. This clamp with the folded ears on the sides is for the 7/8 and 15/16 inch front sway bars.
Availability: In-Stock Item
Item #: 10024 -
Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.
Availability: Ships Direct from Supplier (Except International)
Item #: 10023 -
DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.
Availability: In-Stock Item
Item #: 16161 -
Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs.
Availability: In-Stock Item
Item #: 61616 -
Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs. These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H
Availability: In-Stock Item
Item #: 15822 -
Reproduction sway bar mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.
Availability: In-Stock Item
Item #: 15821 -
Reproduction sway bar clamp mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.
Availability: In-Stock Item
Item #: 32154 -
Bolt kit for installing front sway bar clamps to the body for any 1967-68 Mercury Cougar or Ford Mustang. 3/8" bolts for 1967-68 cars. Starting in 1969, the bolt size was changed to 5/16". This size of bolt is obviously stronger and can be used on all cars 1967-73.
Availability: In-Stock Item
Item #: 32637 -
Original passenger side sway bar mount for your LATE 1968-70 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions available in 1968. Both curved and straight cut, even on the same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, this is the passenger side only....
Availability: In-Stock Item
Item #: 32638 -
Original driver side sway bar mount for your LATE 1968-70 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions available in 1968. Both curved and straight cut, even on the same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, this is the driver side only. See related...
Availability: In-Stock Item
Item #: 32640 -
Original passenger side sway bar mount for your 1967- early 1968 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions of this bracket were used starting in 1968. This version has a straight cut edge on the front section, later versions were curved. Straight and curved mixed during 1968 on same car. Original part number is 5A483. The MPC and other manuals refer to this...
Availability: In-Stock Item
Item #: 32641 -
Original driver side sway bar mount for your 1967- early 1968 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions of this bracket were used starting in 1968. This version has a straight cut edge on the front section, later versions were curved. Straight and curved mixed during 1968 on same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as:...
Availability: Used / Wrecking Yard Item
Item #: 15641 -
This used under dash wiring harness repair pigtail is from the tachometer, turn signal switch, ignition switch, and back-up lamp switch to the driver side (left hand) door pillar. This is part of the 14401 main under dash wiring harness.*NOTE* This pigtail also has a pink resistor wire that should not be cut or spliced because it's ohm resistance is dependent upon it's length.**NOTE** Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on...
Availability: Used / Wrecking Yard Item
Item #: 15639 -
Used under dash wiring harness repair plug and pigtail to the driver side (left hand) map switch on the dash of your Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15629 -
Used under dash wiring harness repair power lead plug and pigtail repair for the under dash harness for the Mercury Cougar. This is a power lead for the fuse block / box and is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15623 -
Used wiring plug and pigtail repair for the under dash harness on the Mercury Cougar Standard and XR7. This plug and pigtail will work for the front marker lights, the battery side solenoid, or the right or left turn signals. This is part of the 14401 main under dash wiring harness.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...
Availability: Used / Wrecking Yard Item
Item #: 15636 -
Used under dash wiring harness repair plug and pigtail for the seat belt relay on your Mercury Cougar Standard. Good for Standard and XR7 models.
Availability: Used / Wrecking Yard Item
Item #: 15660 -
Used under dash harness plug and pigtail to repair the passenger side (right hand) leads to the fuel sender / K-8/9 relay for your Mercury Cougar Standard and XR7. This is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15667 -
Used under dash wiring harness repair plug and pigtail to the wiper coordination switch (foot pump/washer) for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.*NOTE* The individual wires can be removed and the block is also available without the wiring pigtail.
Availability: Used / Wrecking Yard Item
Item #: 15666 -
Used repair plug and pigtail goes from the under dash harness thru the firewall to the heater motor on non A/C Mercury Cougars. This harness repair pigtail comes with the thru firewall rubber grommet and is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15670 -
Used under dash wiring harness repair plug and pigtail for the turn signal indicator relay on your Mercury Cougar. This is part of the 14401 main under dash wiring harness.**NOTE** Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information...
Availability: Used / Wrecking Yard Item
Item #: 15628 -
Used ground wire for the relay panel next to the fuse panel / block on the Mercury Cougar Standard and XR7.
Availability: Used / Wrecking Yard Item
Item #: 15662 -
Used under dash wiring harness repair plug and pigtail that goes to the blower motor fan switch for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15657 -
Used under dash wiring harness repair plug and pigtail to the dimmer switch for the Mercury Cougar. The individual wires and the bare plug can be purchased separately and are part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15627 -
Used fuse block / box and pigtail for the under dash harness on the Mercury Cougar. This is part of the 14401 main under dash wiring harness.Ford part # C6OZ-14A068-A.*NOTE* This unit has the same wire color and configuration as the 1967 version. The only difference is the wire retaining clip.
Availability: Used / Wrecking Yard Item
Item #: 15656 -
Used under dash wiring harness repair plug and pigtail lead to the cigar / cigarette lighter for the Mercury Cougar Standard and XR7. This is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15632 -
Used under dash wiring harness repair plug and pigtail for the Mercury Cougar Standard. This unit can go to either the courtesy "C" pillar lights, the emergency brake warning relay, the circuit breaker for the license plate light, or either side of the front marker lights. This is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15661 -
Used under dash wiring harenss repair plug and pigtail to the wiper motor for the Mercury Cougar. This is part of the 14401 main under dash wiring harness. We also carry the mate for this pigtail. You can check wire colors for correct pigtail.
Availability: Used / Wrecking Yard Item
Item #: 15658 -
Used under dash wiring harness repair plug and pigtail to the low fuel relay for the Mercury Cougar XR7 or Standard model with the Safety and Convenience option. This is part of the 14401 main under dash wiring harness,
Availability: Used / Wrecking Yard Item
Item #: 15644 -
Used under dash wiring harness repair plug and pigtail for the parking brake warning light in the overhead for the Mercury Cougar XR7. This unit connects at the passenger side door jamb to the overhead harness. This is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15631 -
Used under dash wiring harness repair plug and pigtail for the circuit breaker to the sequential motor for the taillights for the Mercury Cougar Standard and XR7. This is part of the 14401 main under dash wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot...
Availability: Used / Wrecking Yard Item
Item #: 15645 -
Used under dash wiring harness repair plug and pigtail lead to the oil pressure gauge and oil pressure gauge lights for the Mercury Cougar XR7. The individual leads can also be purchased separately. This is part of the 14401 main under dash wiring harness.Check out our video below on how to use the new gauge tester: ...
Availability: Used / Wrecking Yard Item
Item #: 15638 -
Used under dash wiring harness repair plug and pigtail to the passenger side (right hand) dash mounted map light switch on the Mercury Cougar. This is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15647 -
Used under dash wiring harness repair plug and pigtail leads to the map light switches to the overhead wiring harness at the passenger side (right hand) door jamb for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 15646 -
Used under dash wiring harness repair plug and pigtail to the "C" pillar courtesy light switch mounted on the dash for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.Fits:1967 Mercury Cougar XR71968 Mercury Cougar XR7
Availability: Used / Wrecking Yard Item
Item #: 15626 -
Used under dash wiring harness repair plug and pigtail for the reverse / brake lights to the turn signal relay for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great...
Availability: Used / Wrecking Yard Item
Item #: 15637 -
Used under dash wiring harness repair plug and pigtail to the windshield wiper switch for the Mercury Cougar. The individual wires can be removed and the bare plug can also be purchased separately. This is part of the 14401 main under dash wiring harness.