All Available Parts - 1968 Mercury Cougar

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, Sold as a pair. Replaces Ford part #: C5ZZ-13206-B and C5ZZ-13207-B.

Ford never offered this socket / plug assembly on its own but we do from time to time get one that has a clean socket and no cuts in the wiring. You can often just twist and pull (after the bulb has been removed) and it will come right out of the chrome housing. The Ford engineering number imprinted on the wire is C8WB-15A442-A.

Coming from Western parts cars these brackets are unusually nice in comparison to what you will find in other regions. For and extra $1.50 we can include the mounting nuts. Right is the same as left, two brackets required per car, sold individually.

Good used light with no pits or scrapes. Does not include lens or pigtail with socket, does include mounting bracket with two nuts. The chrome body carries a C8GB-15A428-B engineering number and the pigtail has a C8WB-15A442-A engineering number imprinted on the wire. We usually only have one or two in stock of this caliber so do not be surprised when you try to place this in your cart and it shows 0 quantity. Even though this is the best we will ever have to offer off of a Western parts car...

This grade "B" light bezel will have minor blemishes in the chrome as shown. Good part for a driver as it will not have deep pits. Does not include pigtail or lens. Left is the same as right. To remove pigtail from your existing light wrap socket in cloth to protect and grip firmly with a pair of pliers, rock back and forth while pulling and the plug and socket assembly should come right out from the back side. Replaces Ford part # C8WY-15A201-C.

Good used lens with average wear but no cracks. Right is the same as left, two required per car.  No mounting hardware included. We also have grade "B" lenses at a substantial savings.

This XR7-G Lucas Square 8 light is in average condition with pitted glass, missing plug ends, and pitted spacers. *NOTE* The lens shown is actually mounted upside down for Cougar use.

Great chrome on this reproduction backup / reverse light for the passenger side (right hand) of the the Mercury Cougar or Ford Mustang. Lens, gasket, and bulb sold separately. Replaces Ford part # C7ZZ-15511.

Great chrome on this reproduction backup / reverse light for the driver side (left hand) of the Mercury Cougar or Ford Mustang. Lens, gasket, and bulb sold separately. Replaces Ford part # C7ZZ-15512.

Hassle free kit makes it easy to install backup lamps. This kit includes mounting pads, lenses, gaskets, T1142 Bulbs and mounting hardware.

These unique studs embed / clip into your core support to fasten the headlight bucket to the radiator core support. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Screws and spring clips for the tank or reservior for vacuum system

Sold individually Attaches the lens to the light housing. Fits all 1967-70 Mercury Cougar or Ford Mustang.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Sold individually. Stainless Steel

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Reproduction side marker light socket with harness set. For all 1968 Mercury Cougar and Mercury Montego and Cyclone. This listing is for a pair of wiring harnesses with light sockets. The original sockets were a snug fit in the fender light housings. These sockets are a slightly larger diameter than original and work well with the reproduction housings, but you may need to enlarge the hole if you're using your original housings. These wiring harnesses look real sharp with our reproduction...

Reproduction driver side (left hand) and passenger side (right hand) front turn signal / parking light assemblies for the Mercury Cougar. These units come with the correct amber bulbs, clear lenses and have the original working wiring pigtails already spliced in. These are sold as a pair only. Keep in mind there were slight variations between 1967 and 1968 (a simple A clip on the wiring harness). We no longer carry both versions, we use the same wiring on both years. If you would like to...

Perfect in every detail down to the FoMoCo logo. Used on the 1968 Montego / Cyclone / Cougar for the 1968 model year. Great reproduction made from the original Ford tooling. This is the Concours version with FoMoCo marking on the lens. Listing is for the reflector only, does not come with gasket or hardware. Also, don't forget the rubber protectors that slip over the pointy studs inside the trunk. Replaces Ford part #C8GY-13380. ...

Good used pair of taillights that includes two average grade "B" bezels and two used grade "B" lenses with backing plates. No obvious cracks in the lenses but there will be stress cracks that will only be found under close inspection. The bezels will have good chrome with no obvious defects but the paint will need attention. This is a good saving over buying the four or six parts individually. Don't forget to pick up a set of gaskets for the lenses as they always are needed after 40 plus...

Headlight relay kit converts the 1967-68 Mercury Cougars with quad or 4 headlights to modern car technology (kit also works on 1967-68 Mustang 2 headlight systems). If your Cougar suffers from dim headlights you are not getting a full battery power to the back of your headlamp bulbs. Safe for use on our vintage cars. Still uses your headlight switch. Instead of carrying reduced voltage to the headlights through the switch, the switch triggers the relay, which takes power directly from the...

Headlight relay kit converts the 1967-68 Mercury Cougars with quad or 4 headlights to modern car technology (kit also works on 67-68 Mustangs 2 headlight system). If your Cougar suffers from dim headlights you are not getting a full battery power to the back of your headlamp bulbs. Safe for use on our vintage cats. Still uses your headlight switch. Instead of carrying reduced voltage to the headlights through the switch, the switch triggers the relay, which takes power directly from the...

Nice reproduction rear body side reflector as found on 1968 Mercury Cougars. Used on Montego / Cyclone / Cougar for the 1968 model year. Great reproduction, but without the 'FoMoCo' marking like on our concours version. This reflector comes with the rubber gasket and attaching nuts. Very nice and at an attractive price. You'll also want these rubber protectors for the trunk.Replaces Ford part # C8GY-13380-A. *Note - Also fits 1968 Mustang after Feb 15, 1968. *Trivia - 1968 Mustangs did not...

Reproduction backup light mounting spacers for the Mercury Cougar or Ford Mustang.

Good used lens with average wear and may have some cracking and hazing. Right is the same as left, two required per car. No hardware included.

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

Good used grade "A" taillight bezel for the 67-68 Mercury Cougar. This grade "A" unit will not have any pits, bends on the ribs and the chrome will have good luster. When you mention it in the comments section, we will try to pick out examples that still have the detail paint in tact. This no excuses bezel will look great on your high quality unrestored driver. Right and left are interchangeable. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

This is a complete set of four used headlight bulbs, marked with the FoMoCo logo. These sets come with two high beam and two low beam bulbs. Each bulb is tested by the electrical department. If you're trying to keep your Cougar or Mustang as close to original as possible, you should definitely grab a set.These bulbs are date coded, so if you want a particular date, be sure to mention it in the comments section of your order.  

These are the little 11/32" lock nuts (sometimes called speed nuts) that you use to attach the taillight bezel to the taillight housing. 10 nuts per bezel, 20 per car.

100% complete assembly with near perfect chrome, tested socket, good used bulb and all hardware needed to install. Perfect choice for that all original low mile survivor that shows some patina. Mustang is different and the reproductions must be modified to work on the Cougar. 68 plugs differ from 67 plugs and whereas PS and DS look similar they are in fact side specific. New mounting pads and lens gaskets are sold separate.

100% complete assembly with near perfect chrome, tested socket, good used bulb and all hardware needed to install. Perfect choice for that all original low mile survivor that shows some patina. Mustang is different and the reproductions must be modified to work on the Cougar. 68 plugs differ from 67 plugs and whereas PS and DS look similar they are in fact side specific. New mounting pads and lens gaskets are sold separate.

Reproduction 22" pigtail for the 67-69 front turn signal wiring harness. Please Note: The Cougars are wired differently than some Mustangs. On some Mustangs the brown wire goes to a male plug.   This plug is a reproduction of the Cougar plug. Here is an example from the reproduction tail light we sell showing the difference: For installation on a Cougar, match up: Black Wire Black Wire Light Blue Wire Light Blue / Off White Wire Brown Wire Brown Wire ...

Reproduction halogen headlight conversion kit. Included in this kit are the four halogen headlight bulbs (2 high and 2 low) and the mini-relay kit, which is needed when installing halogen bulbs on your 67 - 68 Cougar. The 55 Watt Xenon Halogen H4/9003 bulbs included in this kit are "cool white" which have a bit of a blueish tint, like you see on modern cars. If you would like to go with a more original "natural white" color, you can buy these inner replacement bulbs. This kit comes with the...

Reproduction pair of halogen headlights for any 67 - 73 Cougar or Mustang. These bulbs work for both high and low beam, you simply need to bend one of the tabs back for high beam (see photo above). Keep in mind that you will need a headlight relay kit when installing halogen headlights on your car.  Benefits of switching to halogen bulbs: Brighter lightDramatically improves driver visionOptical lens for a powerful beamLong range high powered lightsCrystal clear glass face with H4 halogen...

Used backup / reverse light for the passenger side (right hand) of the the Mercury Cougar and Ford Mustang. Lens, gasket, and bulb sold separately, but we do have a kit available. These used lights will often have a minimal amount of pitting on the inside close up to the lens. Perfect inexpensive replacement item for those wanting to keep their car all original and match the overall patina of their low mile car. Casting number as seen on the back side reads C7ZB-15515-A.Replaces Ford part #...

Used backup / reverse light for the driver side (left hand) of the Mercury Cougar and Ford Mustang. Lens, gasket, and bulb sold separately, but we do have a kit available. These used lights will often have a minimal amount of pitting on the inside close up to the lens. Casting number as seen on the back side reads C7ZB-15A509-A. Replaces Ford part # C7ZZ-15512.

Excellent reproduction front side marker lens. Right is the same as left, two required per car.

Reproduction amber parking light / turn signal lens. This was actually used on the 64 - 66 Mustang which used the amber lens and clear bulb, as compared to the 67 - 68 Cougar which used the clear lens and amber bulb. Sold without gaskets or hardware (see related items).Sold individually

Used inner and outer driver side (left hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety.*Customer Feedback*"I know Don Rush is a trusted and well respected guy. I would just like to give my opinion of him and his team from a Cougar owner in the UK. On one end of the spectrum you have the low lives such as XXX XXXXX who will scam you at the drop of a hat. At completely the opposite end you...

Used inner and outer passenger side (right hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.Used inner and outer passenger side (right hand) wheel house...

Reproduction lower rear window channel patch panel for the Mercury Cougar. It is fairly common for the rear window channel area to develop rust, especially with vinyl topped cars. *NOTE* If you are going t install this part on a Cougar with a vinyl top, you will have to drill holes for the vinyl top moulding / trim.

Used transmission tunnel specialty cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the area you're working on and send us a few digital pictures so we can cut to your needs. Pricing may not change, because we're...

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 69 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness. NOTE: From the factory, Ford made the alignment tabs different passenger vs...

Complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 1969 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness.NOTE: From the factory, Ford made the alignment tabs different passenger vs driver side...

This kit is what we recommend to fully convert your 1968 Cougar over to LED Plasma exterior lights. Our WCCC brand LED lights are amongst the brightest on the market and have been specifically engineered with the nuances of the Mercury Cougar sequential system in mind. Keep in mind that over the years folks have become accustomed to very BRIGHT tail lights in traffic and the old incandescent bulbs are not only dim, but they take time to fully illuminate and a split second can make all the...

Used passenger side parking light / front turn signal retainer. Ford part # C5ZZ-13206-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used driver side parking light / turn signal retainer. Ford part #: C5ZZ-13207-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

This pair of tail light bezels have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.  If you send cores in for exchange they must be pit free and no scrapes so as to...

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

If your pump works fine but leaks this is an easy kit to install. Replaces Ford Part #: D1AZ-3B584-A.

Replaces Ford part # C7AZ-3A006-C or D1VY-3A006-A.

Replaces Ford part # C7AZ-3A006-C of D1VY-3A006-A.

1967 - 1971 Ford power steering pump dipstick. Used until 2-8-1971.

Due to the vulnerable location of the control valve these often get cracked or worn through from rubbing on other components. Fits most all Ford passenger cars 1962-1970. Replaces Ford part number C2AZ-3C705-B

Reservoir Attaching Nut 351335-S38 - Used Nuts for attaching the oil reservoir to the pump. The larger of the two nuts goes against the can. Threads of 5/8"-18 to fit the high pressure port. This is a pair of nuts, one tall and one short. Please follow the assembly procedures for the Ford power steering pump in the Ford shop manuals. Fits all small block V-8 engines, except for 1970 with 351 engine, and Mustang with 302 engines. 1970 302 / 351 engines used a different pump with an offset...

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.Measures 21" long

NOTE - Some customer are experiencing problems with this economy idler arm, the castle nut on top is causing clearance issues with the bolt on the top arm.Import reproduction. Fits 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 40,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering.

Reproduction Power Steering Return Line Hose Clamp for the 1967 - 1973 Mercury Cougar

Premium grade of idler arm. Fits all 1967-70 Mercury Cougar and Ford Mustang. If you have loose / sloppy steering, replacing this part could help tighten things up. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Drag link hole size: 5/8" Customer feedback: Hey, just wanted to thank you for your prompt service. Last Friday...

C7ZA-3590-C 1967 - 1968 Power steering box pitman arm with 1-1/8" inch sector shaft. Ford part number C7ZZ-3590-C.Having issues with wobbly or loose steering? Check out our video on sloppy steering below.

Power steering drag link for any Cougar or Mustang from 1967 - 1968 with factory power steering system. *Concours tip - This is a natural cast iron part that originally had a yellow stripe for identification on the assembly line.Replaces Ford part number C7ZZ-3304-B .

Sold individually # 377112-S

Great kit for those that have a good used power steering control valve unit to rebuild.  Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #: C2AZ-3A533-A.

Power steering pitman arm for any 1967-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts. This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Premium quality original FORD valve that has been re-manufactured to original tolerances. Quality part that is rebuilt by a true craftsman here in the USA. *NOTE: Our rebuilt and reproduction control valves all come pre-lubed with the correct amount of grease. If out of the box you add more grease, you will damage the valve. Unlike some suspension parts these are not designed to add grease until you see the grease coming out of the seal. Our warranty does not cover over lubricating. ...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm.These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will...

Reproduction power steering control valve sleeve / socket for the Mercury Cougar or Ford Mustang.

These are the newest steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be a great buy because of the fact that they come with a lifetime guarantee. These gear boxes are not rebuilt, as are the rest of the boxes we carry, so there's also no core charge. 16:1 ratio NOTE* The supplier specifies that these steering boxes are made with new and used parts. Having issues with wobbly or loose steering? Check out our video on sloppy steering...

Reproduction spool for the control valve on your 67 - 70 Cougar or Mustang.

Reproduction repair kit for your 69 - 70 Cougar or Mustang Midland brake booster inner control valve.When doing the repair on your booster control valve, be sure to use any type of synthetic blend grease and lubricate the following:Inside lower end of the bellows, all O rings and insides of the seals and inside the front diaphragm.Included in this kit are 3 O rings, fiber washer, rubber valve, spring and spring seat and spring retainer.

Reproduction 1/2" hose clamp, commonly used on the fuel lines. This clamp is smaller than the ones used on the power steering return line.

New castle nut for all power steering control valve ball stud found on 1967-70 Mercury Cougar and Ford Mustang. 3/4 inch hex nut, with 1/2-20 threads. Connects the Pitman arm to the ball stud on the P/S control valve. Don't forget the cotter pin. Verify your shop manual for correct year torque specifications. We found one source of 28-35 FT LBS. for the Pitman Arm nut to control valve. Ford numbers for attaching nut: 1967-68 351059-S, 1969-70 385002-S.

Most complete kit available for rebuilding the late 1967-70 Mercury Cougar or Ford Mustang power steering control valve. Includes a very accurate sleeve, all 4 seats, and various seals and hardware. Please note that the early 1967 control valves did have 1/4 inch lines. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #:...

Reproduction power steering control valve boot and clamp, for the 1967-70 Mercury Cougar or 1965-70 Ford Mustang. Gold tone clamp, molded rubber boot, and pair of screws. Very accurate reproduction. 

Used C-4 transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Cast aluminum construction, the 1968 Cougar version will have the provision for mounting the damper weight on the bottom. 1967 tail shafts with a casting of C6DP-7A040-A will not accept the vibration damper weight. 

Used C-4 transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1967-68 Mercury Cougar and 1967-69 Ford Mustang cars with transmission code W on the door tag. Cast aluminum construction, the 1968 Cougar version will have the provision for mounting the damper weight on the bottom. Replaces Ford part number C6DP-7A040-A.

Used tube with a tapered end for the vacuum modulator on 1967-68 Mercury Cougar or Ford Mustang with drum brakes and C4 or automatic transmission, but without power drums or power disc brakes. With power brakes the vacuum hose was connected to a fitting in the intake manifold. Pictured in the Bob Mannel Ford Small Block V8 on page 7-26. The basic Ford part number is 7B094.*Note - this tube is not used with disc brakes.

Bare cast aluminum C4 transmission case from a 1967-68 Mercury Cougar or Ford Mustang. Inspected for damage. Replaces Ford part number C6DP-7006-A.

Used servo cover from a 1967-68 Ford C-4 transmission. This cover has the big A cast into it, which designates it as an "A" servo. Cover only, marked C6AP-7D027-C.

Two piece pre-bent Stainless steel brake line kit that runs down the rear axle on the 8 inch rear end of a 1967, 1968 or 1969 Mercury Cougar or Ford Mustang.The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of...

This is a "better quality" non-concours starter solenoid. It's just one step above our "generic" solenoid also listed on our site. An inexpensive replacement if you are not worried about being 100% correct. More often than not, these lower quality solenoids fail within a year or two so we always recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.Cougar Applications:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury...

Cast iron construction similar to the 1967 bracket but made to fit the 1968-1970 style smog pump with 3 bolt pulleys. Ford part number C8AZ-9B450-B, casting number C8OE-9B450-A. Mounting hardware sold separate.

Application 1968 - 289-2V, 302-2V, 302-4V, all with manual transmissions and without air conditioning. Also 1968 390-4V and 1968 - 1970 428CJ, all without air conditioning. Pulley diameter 4.75" inches. Ford part number is C8AZ-9B447-B and the engineering number as seen on the front of the pulley is C8AE-9C480-A.

Common air pump for all 1968 - 1970 thermactor emissions systems. 1968 289-2V, 302-2V, and 302-4V all with manual transmissions, and 1968 390-4V, 427-4V all domestic US Cougars. Additionally all 1968 - 1970 428 Cobra Jets, and 1969 - 1970 Boss 302 Eliminators. Identified by the use of 3 attaching bolts for the drive pulley, a white colored cooling fan, and a round pressure relief valve on the side of the pump. Later pumps do not have this pressure relief valve. Good used thermactor smog air...

Application is 1968 289-2V, 302-2V, and 302-4V all with manual transmissions. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut/ one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube. New Old StockFord part number C8OZ-9B471-A.

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.New old stock Ford.

Flexible high pressure replacement brake hose for front drum brakes that fits both passenger (right hand) and driver (left hand) sides of Mercury Cougar or Ford Mustang. Sold individually, please remember to order two if a pair is needed.Replaces Ford part # C7ZZ-2078-A.

Flexible high pressure replacement brake hose for the front driver (left hand) side of Mercury Cougars or Ford Mustangs equipped with disc brakes.Replaces Ford part # C8ZZ-2078-B.

Flexible high pressure replacement brake hose for the front passenger (right hand) side of Mercury Cougars or Ford Mustangs equipped with disc brakes.Replaces Ford part # C8ZZ-2078-A.

American made! Flexible high pressure replacement brake hose for the rear drum brakes on Mercury Cougar and Ford Mustang. Attaches to the rear end housing. 8 inch and 9 inch rear ends 1967-69 all with 28 splined rear axles.Replaces Ford part number C7ZZ-2282-A. *NOTE* Excludes 427, 428, and 1969 Boss 302 Eliminators.

Flexible high pressure replacement brake hose for the rear drum brakes on Mercury Cougar and Ford Mustang. The Ford MPC specifies that the 427, 428 and Boss 302 cars used this slightly different hose. The most noticeable difference is the bracket that attaches to the differential and the larger size fittings. Attaches to the rear end housing. Replaces Ford part number C9ZZ-2282-A.

Offshore Centric brand reproduction flexible high pressure replacement brake hose for the rear drum brakes on Mercury Cougar and Ford Mustang. Attaches to the rear end housing. Replaces Ford part # C7ZZ-2282-A. *NOTE* Excludes 427, 428, and 1969 Boss 302 Eliminators.

Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.

Copper crush washer for all disc brake hoses and calipers 1968-73 Mercury Cougar and Ford cars like Mustang. Size 0.39" x 0.62" x 0.062". Four needed per car, two per side (one on each side of the disc brake hose end) sold indiividually.

Used front drum brake hose bracket for any 1967-70 Mercury Cougar or Ford Mustang. Simple bracket bolts to the front aprons and holds the brake hoses stationary. Right and left side are the same.Ford part number C1SS-2082-C.

Used bracket for mounting the rear axle flexible brake hose. This is a factory welded in bracket that was removed from a 1967-69 Mercury Cougar or Ford Mustang. Double check your placement for your particular year, when welding the bracket to your car. Good used bracket the you need to separate from the factory spot welds. Part bead blasted for photo, has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Ford part number C7ZZ-2A051-A.

Power steering pitman arm for any 67-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts. Replaces Ford part number C9ZA-3590-A This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Reproduction machined tube seat set, for all 1968-70 Mercury Cougar and Ford Mustang. Also some 1967 Cougar or Mustang control valve and ram cylindernwith the 5/16" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that early 1967 control valves had 1/4" fittings.

Application is 1968 289-2V, 302-2V, and 302-4V all with manual transmissions. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut/ one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.