All Available Parts - 1969 Ford Mustang

Support brace between the cowl top and the brake pedal support bracket. Fits 1969-70 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Ford part number C9ZB-6501554.

Support brace between the bottom of the steel lower dash panel and the cowl top. Fits 1969-70 Mercury Cougar and Ford Mustang with either air conditioning or without air conditioning. Ford part number C9ZB-6504672-A.

Angled bracket for mounting the steel dash panel to the cowl. Two brackets per car, sold individually. These are the end mounting brackets for all 1969-70 Mercury Cougar and Ford Mustangs with or with air condtioning. Ford part number C9ZB-5404366.

One end attaches to the right of the brake pedal support, and the other to the dash panel. Original Ford part number C9ZB-6504510.

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

These plastic vertical trim parts mount under the dash pad, to the right and left of the radio. Available in black only, sold as a pair and "almost" as nice as our originals but you will notice the grain (texture) is less defined on the reproductions. We have perfect used in an array of colors. *Customer Feedback* "I have checked out this website several times and it is a great source for information and these guys know what they are talking about. They are friendly and willing to help with...

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang without factory air conditioning, this panel does not have the round holes in the outer section. This is not a reproduced part, only the 'with' A/C panel is reproduced. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade A used, no pitting, no...

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang without factory air conditioning, this panel does not have the round holes in the outer section. This is not a reproduced part, only the 'with' A/C panel is reproduced. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade B used, may have...

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade B used some pitting and or  extra holes. Replaces Ford part number C9ZZ-6504320-D.

If you look close at our used set I do not think you could tell the difference, look at the back side in comparison to used and you will see a noticeable difference. *NOTE* The fifth part slips into the backside of the inner knob on the passenger side and acts as a spacer for Cougars or Mustangs without the rear fader option. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. ...

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. The pictures show an example of how it looks once installed. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. Also found on various 1976-70 Ford and Mercury cars such as Galaxie, Fairlane, Torino, Ranchero, Falcon, Montego, and Thunderbird. The knobs...

Nice clean set of four used radio knobs for your 69-70 Mustang or Cougar. No peeling or cracks. The inset picture shows the used next to the new from the backside. The reproductions are shown on the right. Whereas the repros are nice, the originals are still superior. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. White plastic reproduction spacers available here. The white...

Replaces grommet in chrome oil cap with PCV valve. Inside diameter is 37/64". Replaces Ford part #: C8AZ-6892 or C8AZ-6A892-A.

A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. 1967 AM-FM radios would use this part as they did not have a balance feature. Called a "Sleeve" 1969-70 Cougar and Mustang AM radios use this sleeve. Also found on various 1970-76 Ford and Mercury cars...

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out this video Still have riv-nut questions? Here are riv-nut answers! ...

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

New mirror glass, for the passenger side on practically any 1969-73 Ford with painted sport mirrors. This is the convex style of mirror, think "Objects in mirror are closer than they appear". Nice fit, exact shape of originals. Dimensions: 4 3/8 x 2 7/8 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video Check out this video ...

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

Good used part without excessive rust or damaged rubber. For use with fixed column only.

Three required per car, includes washer. Used in conjunction with a steel clip to secure lower flange to column tube.

Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

New foam insulation for the lower tube of the steering columns. Can be used on fixed and tilt columns, from 1968-73, on all Mercury Cougars, Ford Mustangs, and most all other Ford steering columns with a lower tube with inside diameter of 1-5/8 inches. The originals have almost always disintegrated. Adhesive probably isn't needed, but we recommend just a little drop of something to hold it in place. This is a dense foam insulation ring. DIY guys, this material can be found in bulk at home...

12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.

Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...

Bare outer tube for the 69 Cougar or Mustang tilt steering columns. This item will be free of major rust, and will have to be painted to match your car. Keep in mind that these tubes are year specific. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Check out this video ...

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Floor mounting column bracket for the 69-70 Cougar or Mustang. Rubber gasket may not come with bracket, and if it does will most likely need replacing. Undamaged with original fasteners. Get the gasket here.Ford part number C9ZZ-65017A50-A.

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.

Used lower shaft fixed steering column found from 1968-69 Mercury Cougar or Ford Mustang. This is the portion that mates with the upper shaft that bolts to the steering coupler. 1968-69 lower shafts are 15-1/2 inches in overall length. They also have a lower flange with flat sides. Other Ford fixed lower shafts can be used, in most cases the sheer pins are already broken. Just slide the shafts together for the desired length. WCCC no longer has an in-house service for tilt and tilt-tilt away...

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Reproduction transmission selector tube seal for the 69 - 70 Cougar or Mustang steering columns.

C9ZP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1969 Mercury Cougar and Ford Mustang with 351 engine and automatic FMX transmission, code X on your door data plate tag.

Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. D2ZP-7A040-A version also available, we have a good supply of the updated 1972 version. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos.  This housing will not fit full sized Ford Mercury cars that have an FMX,...

Brand new flex plate for all 1969 - 73 Mercury Cougar and Ford Mustang with 302 / 351W / 351C engines, and C4, C6, or FMX transmissions. Comes complete with new starter ring gear installed as shown.*Note - Fits common torque converter bolt pattern of 11.40 inches. In 1972 there was a unique C6 torque converter with a 9.50 inch bolt pattern. 

Ultra rare C-6 transmission cast iron tail shaft for any 428 Cobra Jet or 429 Cobra Jet. Nice condition, has casting number RT-C8OP-7A040-A on side as shown. 1968-71 Mercury Cougar, Ford Mustang and Torino / Cyclone / Ranchero with Q or R code 428CJ engines including 428SCJ engines. J and C code 429CJ engines too for 1970-71.Ford MPC number C8OZ-7A039-B.

Good used OEM flex plate for all 69 - 73 Mercury Cougar and Ford Mustang with 302 / 351W engines, and C4 or FMX transmissions. Not for use on a 1968 with 302. The starter ring will show wear and some will choose to replace, others have removed the starter ring and just turned it around so the unused portion of the ring will now contact the starter drive gear. ...

New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S

Set of 6 new correct bolts for attaching the FMX transmission to 351 engines. Fits all 1967-73 Mercury Cougar and 1967-73 Ford and Mustang with transmission code X, or FMX automatic transmissions. Quality fasteners from AMK.

Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. C9ZP-7A040-A version also available for slightly more money. Exact same part, just got updated for some engineering or manufacturing reason. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos.  This housing will not...

Replacement seal with boot for all 1965-73 C4 Ford transmissions. Tail shaft and slip yoke seal. 

Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions. 

Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the C4 transmission valve body for all 1967-67 Mercury Cougar and 1967-69 Ford and Mustang. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the FMX transmission valve body for all 1969-72 and 1969-72 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.* Note - 1973 has a different shift kit, see related items.

Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford. 

Cork pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Rubber gasket also available.

Rubber pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Cork gasket also available.

Transmission pan gasket for the FMX transmission on any 1969-73 and 1969-73 Mercury Cougar and Ford Mustang.

Basic C6 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C6 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that U code C-6 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.

Basic C4 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C4 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops. 

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Tall style filter for C4 transmissions.  Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.

Replacement tail shaft bushing, for all 1964-73 C4 transmissions.

Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place.  Ford part # D1AZ-3518 or E2AZ-3518

Used upper steering column shaft for a fixed steering column on the LATE 1969 Mercury Cougar or Ford Mustang, after about 1/13/1969. As shown, will need retainer clips and various C-clips and or Snap rings. Inspected for good threads for attaching the steering wheel. About 24-7/16 inches long. Starting in 1970, Ford had a "nail" type head. Ford part number C9ZZ-3524-A.

Used upper steering column shaft for a fixed steering column on the 1968 and EARLY 1969 Mercury Cougar or Ford Mustang, before about 1/13/1969. As shown, will need retainer clips and various C-clips and or Snap rings. Inspected for good threads for attaching the steering wheel. About 23-3/8 inches long. Starting in 1970, Ford had a "nail" type head. Ford part number C8ZZ-3524-D.

If you have already begun to install or have installed this item, it is not eligible for return or refund. This is far superior to the switch Ford put out as a service part in the 90's. It is imperative that you clean every part of your old switch out before carefully installing the new switch. It is best to start both ends at the same time at 6 o'clock and meet at the middle at 12 o'clock. It measures 44" in length. We've found that these switches are about an inch too long, so you'll...

Correct nut that is designed not to come undone.

Reproduction reinforcement plate designed to weld onto the lower control arms. Sold individually, we are not sure that you would want to even buy one of these. They don't fit very well, and are not contoured to any lower control arm on the market. You will be bending these to fit, prior to welding. *Note - This is a non-returnable item. 

Reproduction ring gear for 164 tooth fly wheels and flex plates as found on 1968-73 Mercury Cougar and Ford and Mustang. Quality new ring gear, check Youtube for installation instructions. 

Reproduction ring gear for 184 tooth fly wheels and flex plates as found on big block 1967-71 Mercury Cougar and Ford and Mustang. Quality new ring gear, check the Youtube for installation instructions. Typically, the engine sizes would be 390, 410, 427, 428, and 429 cubic inches.

Quality reproduction for all 1969-73 Mercury Cougar and Ford Mustang with FMX automatic transmissions. This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug and wire that will not be utilized when used on a 1969-71. All but one plug will be utilized on the 1969-71 applications. This plug and wire is not needed and can either taped off or clipped. Replaces original Ford part numbers C9ZZ-2A247-C,...

This reproduction radiator support crossmember is correct for the 1967-68 Mercury Cougar and Ford Mustang, but will work on any 1967-70 Cat or Pony.Replaces Ford # C7ZZ-6510852-B or C9ZZ-6510852.

THE SUPPLIER IS CURRENTLY OUT OF STOCK ON THIS ITEM. WE WILL UPDATE THIS LISTING WHEN IT IS AVAILABLE AGAIN.This reproduction radiator / core support assembly includes the lower crossmember and is for Mercury Cougar and Ford Mustang. Replaces Ford number C9ZZ-16138-A.

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install.  These are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available...

Straight Monte Carlo Bar in a chrome finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end of your coddled cream puff cruiser or hardcore corner carver, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C9ZZ-16A052-ARC. ...

Two-piece Stainless Rear Axle Brake Line Set 69 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any possible...

Two-piece OE-Style steel Rear Axle Brake Line Set 69 Mercury Cougar and Ford Mustang with 9" - 28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for added protection. ...

Two-piece Stainless Rear Axle Brake Line Set 67, 68 & 69 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any...

Two-piece OE-Style Steel Rear Axle Brake Line Set 67, 68 & 69 Mercury Cougar and Ford Mustang with 9"-31 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for added protection. ...

This is a ignition nut tool used to take the ignition nut out of 1969 Cougar. These are made from HRS steel and are milled to fit the bezel. No more scratches trying to remove with the wrong tools.

Not the correct wood grain for a Cougar.... Here is a piece that will allow to install a modern DIN radio / CD player into your Mercury Cougar or Ford Mustang. No hacking or cutting required! *TRIVIA* Here's some alphabet soup for you. DIN stands for Duetch Industri Normen. An abbreviation for a standard in-dash radio measurement which is approximately 2 inches by 7 inches. The Germans starting using it to standardize the radio's in Audi's, BMW's, Mercedes, and VW's way back in the mid 80's....

This is a 20 inch stock replacement radiator for 1968 - 1969 Cougars without Air Conditioning. In 1967 289 equipped Cougars with A/C came with a 20" two core radiator but we would strongly advise upgrading to a three or four core or even better, a 24" three core radiator if you have air conditioning. Some 1967 Cougars without AC came with an 18" radiator. There is no shroud available for a 18" radiator and we do not sell a reproduction of the 18" radiator, it was a bad idea from the get go......

This is the heavy duty cooling brass core radiator for the big block cats for 1967 - 1970. It also fits the 1970 with the 351C or 351W with Air Conditioning, or the need for heavy duty cooling. Note that the 67 390 Cougar actually used a slightly narrower radiator then this one. If you install this in a 67 you will need the 68-70 lower mounting brackets and a 68-70 shroud. *NOTE* We do not recommend using a four core as it makes fitting the original shroud very difficult, places the fan closer...

For use on fixed columns only. Attaches to the bottom side of the column to keep the wiring in place. Fits all 1968-69 Mercury Cougar, Ford Mustang, Ford Torino, Mercury Cyclone.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Restored stainless steel convertible top trim for the middle section of the exterior boot trim. This is a two piece set of trim, a right and left section, which slip fit together.  We only sell this item on an exchange basis only, you are required to pre-send your restorable cores to West Coast Classic Cougar. These restored pieces work with both the 1969-70 Standard model Cougar and Mustang boot mouldings (even the reproduction die cast chromed mouldings), and 1969-70 Mercury Cougar XR7...

This option REQUIRES sending your cores in advance. Used stainless steel convertible top trim for the middle section of the exterior boot trim. This is a two piece set of trim, a right and left section, which slip fit together. These pieces work with both the 1969-70 Standard model Cougar and Mustang boot mouldings (even the reproduction die cast chromed mouldings), and 1969-70 Mercury Cougar XR7 convertible top mouldings. Limited supply of used and restored available.Replaces Ford part...

Unlike our un-restored used door glass trim and are sold in pairs only. If you are doing a concours correct restoration then these would not be for you as they have been "over restored" to a mirror like finish. The down fall of having such a mirror like finish is they get finger prints on them every time you touch them. The good part is they look HOT! Very nice touch to that resto-mod that cannot get enough bling.When sending cores, they must be in good shape or an upgrade core fee will apply....

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Concours Throttle Return Spring for the 390 / 428CJ / 428SCJ Manufactured after 4-9-69

Bracket that mounts to the rear Carburetor mounting holes of all 1969 351-4V and 428 Cobra Jets or Super Cobra Jets. Has the square hole that holds the factory throttle cable and hole for the return spring.  Replaces Ford part number C9ZZ-9741-B. *Note - This is not a flat bracket like the 1970 351C-4V. There is a distinct drop in the bracket to clear the underside of the Holley carburetor on Cobra Jet equipped cars This is the original factory bracket, reproduction brackets have...

Bracket that mounts to the rear Carburetor mounting holes of all 1969 351-4V and 428 Cobra Jets or Super Cobra Jets. Has the square hole that holds the factory throttle cable and hole for the return spring. *Note - This is not a flat bracket like the 1970 351C-4V. There is a distinct drop in the bracket to clear the underside of the Holley carburetor on Cobra Jet equipped cars.

Used with factory "Autolite" carburetor and aluminum carburetor spacer unique to the 1969 Cougar. Bracket that mounts to the rear Carburetor mounting holes of all 1969 390-4V. Has the square hole that holds the factory throttle cable and hole for the return spring. Has a distinct dip or curve, midway between the mounting holes for the carburetor.Replaces Ford part number C9ZZ-9741-C.

Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.

Leaf spring front bolts for any 1969-70 Mercury Cougar or Ford Mustang. AMK F-251, About 4-3/8 inches long. 4 total pieces, 2 bolts, 2 nuts.

New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.

Reproduction anti-squeak pad for the leaf springs found on the Mercury Cougar or Ford Mustang. This little unit goes between each individual leaf spring and prevents metal to metal contact. These are sold individually and eight are required per car. Our reproduction leaf springs come with this pad pre-installed. Replaces Ford part # C0AA-5586.

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD INDIVIDUALLY. Replaces Ford Part #: KC-55490-A.

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD AS SET OF 8. Replaces Ford Part #: KC-55490-A.

Sold individually. Has correct flattened area at top. Competition handling size, measures 7" from inner radius to end of threads. Thread size 7/16-20".  Does not include the OEM style nuts, those are an optional addon.  Replaces Ford Part #: C6OA-5705-C

These coarse thread nuts have an integrated lock washer with serations for the Mercury Cougar or Ford Mustang. They will ONLY work with the U-Bolts used in conjunction with the lowering kits. The thread size is 7/16"-14. *NOTE* Eight of these are required per car and are sold individually.

All applications 1967-1973 Cougar and Mustang, attaches the drive shaft U-Joint to rear end pinion yoke. Sold individually, two required per car, complete with self locking pinch nuts. Perfect used, no rust or worn threads, these clean up nicely with your benchtop wire wheel.  Note, OEM came with fine threads and no lock washer.Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

Replaces Ford Part # C1AZ-4529-A Sold individually. All applications, attaches the drive shaft U-Joint to rear end pinion yoke. 5/16 Inch Diameter #24 thread for 1 1/8 inch Bearing Caps.

Reproduction universal joint that fits the transmission end of the drive axle on the Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). this unit includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E.