All Available Parts - 1970 Ford Mustang

Limited slip 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and new a seal. Rebuilt using the standard 9 inch case, with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it works for any other Mercurys or Fords with a 9 inch...

Limited slip 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967-1973 standard 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used on any other Ford or Mercury with a 9 inch drop out center section. Because of all the various ring and pinion...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch case with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it can also be used for any other Ford or...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a 1967-1973 nodular 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used in any other Ford or Mercury with a 9 inch drop out center section. Because of all the...

Limited slip, nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Used modern design Detroit Locker unit, new Richmond ring and pinion gear, new Timkin bearings, new selective size sleeve, new bolts, and new seal. Rebuilt using 1967-1973 nodular 9 inch cases with oil fill plug, for 28 or 31 splined axles. This unit was used in 1967-73 Cougars and Mustangs, but it also came in any other Fords or Mercurys with a 9 inch drop out center section....

31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX  cars.  *Excludes 351C-4v and 351CJ engines.

Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually

[No Description Provided]

Reproduction rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1969 - 1970 Mercury Cougar and Ford Mustangs. New part with a course threaded stud, also called a pinion bumper. The correct casting number is seen on this rubber axle bumper is C9OA-4906-A, this version has course threads. The version most often seen on the 1967-68 is C3AA-4906-C. It will have a fine threaded mounting stud.

Includes 2 hex head Screw & Washer Assembly aka "SEMS" bolts for the throttle cable bracket on the 1970 Cougar or Mustang equipped with the 428 Cobra Jet.

This direct replacement features a larger than stock diameter of 2-1/2 inches for increased performance. This is the H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds without the spacer on the passenger side. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 428CJ engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds without the passenger side spacer. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 428CJ engine. We also sell this H pipe in a 2-1/2 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please...

This direct replacement is the 2-1/4 inch H pipe only, and is for any 1970 Mercury Cougar or Ford Mustang with stock 2V cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and custom made for dual exhaust on any 1970 Cougar and Mustang with the 2 barrel H code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351W, 1970 351C-4V, or 1971-73 Cleveland...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock 4V cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 4 barrel M code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351C-2V, or 1971-73 Cleveland...

This direct replacement is the 2-1/2 inch H pipe only and is for any 1969-70 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar Eliminator and Boss Mustang  with the G code Boss 302 engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1969-70 Mercury Cougar or Ford Mustang equipped with the 351W engine with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351W 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351...

This direct replacement is the 2-1/4 inch Y pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang  with the 351C 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351-4V Cleveland engines, or 1971-73 351C engines. Please allow 2...

This reproduction 2 1/4" Tri-Y H pipe to be used with the Patriot style headers on your 1970 Cougar or Mustang.

This reproduction 2 1/4" Tri-Y H pipe to be used with the Scott Drake style headers on your 1970 Cougar or Mustang.

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Right side axle, 28 spline 31-1/8 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

Left side axle, 28 spline 27-1/16 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs.*Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.

Leaf spring front bolts for any 1969-70 Mercury Cougar or Ford Mustang. AMK F-251, About 4-3/8 inches long. 4 total pieces, 2 bolts, 2 nuts.

New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.

Reproduction anti-squeak pad for the leaf springs found on the Mercury Cougar or Ford Mustang. This little unit goes between each individual leaf spring and prevents metal to metal contact. These are sold individually and eight are required per car. Our reproduction leaf springs come with this pad pre-installed. Replaces Ford part # C0AA-5586.

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD INDIVIDUALLY. Replaces Ford Part #: KC-55490-A.

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD AS SET OF 8. Replaces Ford Part #: KC-55490-A.

Sold individually. Has correct flattened area at top. Competition handling size, measures 7" from inner radius to end of threads. Thread size 7/16-20".  Does not include the OEM style nuts, those are an optional addon.  Replaces Ford Part #: C6OA-5705-C

These coarse thread nuts have an integrated lock washer with serations for the Mercury Cougar or Ford Mustang. They will ONLY work with the U-Bolts used in conjunction with the lowering kits. The thread size is 7/16"-14. *NOTE* Eight of these are required per car and are sold individually.

All applications 1967-1973 Cougar and Mustang, attaches the drive shaft U-Joint to rear end pinion yoke. Sold individually, two required per car, complete with self locking pinch nuts. Perfect used, no rust or worn threads, these clean up nicely with your benchtop wire wheel.  Note, OEM came with fine threads and no lock washer.Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

Replaces Ford Part # C1AZ-4529-A Sold individually. All applications, attaches the drive shaft U-Joint to rear end pinion yoke. 5/16 Inch Diameter #24 thread for 1 1/8 inch Bearing Caps.

Reproduction universal joint that fits the transmission end of the drive axle on the Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). this unit includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E.

This reproduction universal joint is forged from high strength alloy steel that is crossed w/ an anti-corrosion coating. This unit also features a grease fitting for an extended life, and fits Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E. Span 3.30" cups 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number...

This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Reproduction universal joint forged from high strength alloy steel and crossed w/ and anti-corrosion coating. Fits the differential end of the drive axle on all 289, 302, 351 Windsor as well as most 351 Clevelands (See Chart). Includes a grease fitting for an extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Reproduction front universal joint that fits on transmission end of the drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-G.

Reproduction universal joint forged from high strength alloy steel that is cross w/ an anti-corrosion coating. This unit fits the transmission end drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (See Chart). this unit also features a grease fitting for an extended life. span 3.60" cup size 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-G.

This reproduction universal joint fits the differential end of the drive axle on all Eliminators and other cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. Replaces Ford part # C3AZ-4635-H.

Reproduction alloy rear universal joint for the Mercury Cougar or Ford Mustang. This unit is forged from high strength alloy steel crossed w/ an anti-corrosion coating. This universal joint fits the differential end of the drive axle on all Eliminators and cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. span 3.5" cup size 1.00" and 1.12" Replaces Ford part # C3AZ-4635-H. ...

These Linear springs are custom wound for the performance-oriented customer. These feature 600-pound/inch rating and will lower the car approximately one inch from stock. Painted black, sold as a pair. Note: If you look close at factory sales pictures from the day you will notice the cars sit about 1" lower in back than front. These springs will level the car out provided your rear leaf springs are not sagging.  Linear springs are the easiest to understand. When you think of a spring,...

Made from soft flexible rubber very similar to the OEM material. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. If you prefer polyurethane insulators, you can find them here. Replaces Ford Part #: C4DZ-5415-A.

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.

Reproduction rubber dust seal or boot for front suspension upper and lower tie rod ends. 1970-73 Mercury Cougar, Ford Mustang, and many other Ford cars.Replaces Ford part # D0OZ-3332

Reproduction rear axle outer bumper for the Mercury Cougar or Ford Mustang. These units mount on frame rail, are push in and two are required per car. Sold as a pair. Replaces Ford part # C6AZ-4730.

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

Reproduction sway bar mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.

Reproduction sway bar clamp mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.

Concours correct reproduction of the front sway bar clamps used on all 67 - 70 Cougars and Mustangs with the competition suspension option, or 15/16th" sway bar. Never available until now. Exactly like the originals in every detail. Standard for all Shelbys, Boss 302s, and Cobra Jets. Stamped and formed just like the originals.

Bolt kit for installing front sway bar clamps to the body for any 1969-73 Mercury Cougar or Ford Mustang. 5/16" bolts for 1969-73 cars. Starting in 1969, the bolt size was changed from 3/8" to 5/16". We stock the 3/8" bolt kits, which was standard for 1967-68 cars. See related items.

Original passenger side sway bar mount for your LATE 1968-70 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions available in 1968. Both curved and straight cut, even on the same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, this is the passenger side only....

Original driver side sway bar mount for your LATE 1968-70 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions available in 1968. Both curved and straight cut, even on the same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, this is the driver side only. See related...

Used under dash wiring harness repair plug and pigtail to the windshield wiper switch for the Mercury Cougar XR7. It was also used on the Standard model after 3/3/1969. This is part of the 14401 main under dash wiring harness.

Reproduction under hood wiring harness repair plugs and leads that go from the under hood harness to the starter solenoid on the Mercury Cougar or Ford Mustang.  Sold as a pair.

Used turn signal wiring pigtail for the 69 - 70 Cougar or Mustang. Pigtail is from the switch side of the turn signal.

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

Used wire set for the dash plug from the main under dash wiring harness from 69 - 70 Cougar or Mustang. Wire colors may vary. NOTE: When ordering, make sure to leave comment on whether you have a Standard or XR7

New wiring pigtail with male bullet connector, and male / female paired connector. Also has rubber grommet that fits a 5/8" inch hole. Looks like 18 gauge wiring. These are remnants from the reproduction Mustang front turn signal lights that we convert to Cougar wiring. Brand new, approximately 13-15 inches in total length. Colors as shown.

Used passenger side (right hand) grade "B" glue in style clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. This glue in style door glass will not work in place of the bolt in versions found in later production models. The glue in style glass was carried...

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

Rear axle vent bolt for the 67 - 73 Cougar or Mustang. This bolt serves a dual purpose, as it also holds the brake line bracket in place on the axle tube.

It took a long time but our supplier finally got this bushing right. They ended up copying a never installed production original bushing Ed Meyer acquired from the Kar Kraft factory back in the day. All details have been copied including the two small ribbed lines located on one side. NOS Bushing notes: If you have NOS C9ZZ-5493-A front sway bar bushings in a Ford bag good luck making them fit. Yes, its a documented fact that almost all NOS 15/16" sway bar bushing Ford sold in a bag are too...

Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-E

D0ZZ-5482-B Factory used front sway bar found on most 1970 Cougars. 3/4 inch in diameter. This factory used front sway bar, does not include mounting anybrackets or end link kits.

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

Early 1970 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the passenger side door, it will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Glue-in or bonded design, will not fit 1969 models and will not fit 1970 bolt in glass brackets. Bonded or glue-in design 1970 glass was used roughly until January 1970, bolt-in glass...

Early 1970 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the driver side door, it will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Glue-in or bonded design, will not fit 1969 models and will not fit 1970 bolt in glass brackets. Bonded or glue-in design 1970 glass was used roughly until January 1970, bolt-in glass...

Used passenger side (right hand) grade "B" bolt in style clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss, Shelby and...

Used driver side (left hand) bolt in grade "B" clear door glass for the Mercury Cougar and Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. This bolt in style door glass will not work in place of the glue in versions found in early production models. The glue in style glass was carried over from...

1970 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the passenger side door, it will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Bolted in design, will not fit 1969 models and will not fit 1970 bonded or glued-in style. Bolt in bracket design, 1970 glass, was used midyear, bonded or glued in glass prior. Ford part number...

1970 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the driver side door, it will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Bolted in design, will not fit 1969 models and will not fit 1970 bonded or glued-in style. Bolt in bracket design, 1970 glass, was used midyear, bonded or glued in glass prior. Ford part number...

Used passenger side (right hand) grade "A" clear bolt in style door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. This bolt in style door glass will...

Concours rear axle vent hose for any 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Rubber hose that attaches to the metal nipple on the top of your rear axle housing. Fits 8 and 9 inch rear ends. Includes hardware as shown. Crimp clamp, screw clamp and bolt. Ribbed hose like original, and has yellow paint mark like from the factory. About 20 inches of hose is included, a little more than what was from the factory. Part number 4A001 in the chassis assembly manual.

Reproduction driver side (left hand) bolt in clear door glass for the Mercury Cougar or Ford Mustang. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked...

This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our...

Reproduction passenger side (right hand) bolt in clear door glass for the Mercury Cougar or Ford Mustang. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked...

Reproduction driver side (left hand) bolt in clear door glass for the Mercury Cougar or Ford Mustang. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked...

Reproduction driver side (left hand) clear glue in door glass for the Mercury Cougar. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In glass? How about...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction bolt in four piece clear glass set for the 1970 Mercury Cougar convertible. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions...

Reproduction four piece bolt in tinted glass set for the 1970 Mercury Cougar or Ford Mustang convertible. This set does not come with any window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are...

Reproduction bolt in four piece smoked glass set for the Mercury Cougar convertible. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. Then there is this version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original...

If you are converting your early 1970 Mercury Cougar or 1969 or early 1970 Cougar Coupe or Convertible from glue in glass to bolt in glass this is the hardware kit you will need. You can reuse your four C9ZB elevators that bolt to these brackets, the only difference between C9ZB and D0ZB is that the C9ZB is fastened by two bolts and the D0ZB has two studs and nuts. Keep in mind that 1969 window regulators will need slight modification to work with this 1970 hardware as the 1970 regulator does...

Good used regulator that was tested in the car and visually inspected once out of the car. Used passenger side or right door window regulator for all 1969-70 Mercury Cougar and Ford Mustangs with glued in door windows. These regulators with the flat end in the lift arm as noted. We suggest lubricating with suitable grease on all of the moving parts and the actual regulator mechanism during the installation. Comes complete with spring, white plastic rollers, and captured steel bushing with...

Good quality reproduction driver side manual window regulator for use on cars with glue in glass. As always, we recommend you use an original used regulator whenever possible. Replaces Ford part # D0ZZ-6523201-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Good quality reproduction passenger side manual window regulator for use on cars with glue in glass.As always, we recommend you use an original used regulator whenever possible. Replaces Ford part # D0ZZ-6523200-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Used drivers side or left hand door window regulator for all 1969 and 1970 Mercury Cougar and Ford Mustangs. *TRIVIA* This style of regulator with the dog legged end on the lift arm, was the service replacement regulator for both 1969 glue in windows and 1970 bolt in windows. Good used regulators that we inspect for operation. We suggest lubricating with suitable grease on all of the moving parts and the actual regulator mechanism during the installation. Comes complete with spring, plastic...

Protects door glass when attaching window channel. Replaces Ford part # C9ZZ-6523258. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video

These inserts snap into your window elevators, four per elevator, eight per door for a total of 16 per car. Often the originals are worn down from lack of lubrication which will cause your door glass to rattle. The originals were more of a clear plastic, these are white in color. These do not fit quite as well as the originals, but work as long as you are OK with the slight play.  For a tighter fit, we recommend that you see the customer reviews of this product for suggestions that...

Most often these do not wear out but instead get lost. These plastic bushings keep the threaded studs from the window elevators from touching the glass as they pass through the holes in your 1970 bolt in door glass. Eight required per car. Replaces Ford part # C9ZZ-6323266 or C9ZZ-6523258-B. *NOTE* These bushings also fit the door glass for the 1969 Mustang Fastback. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or...

383278-S Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs.

Window guide or 'elevator'. 1969 through early 1970 Mercury Cougar and Ford Mustang door glass. Two guides per door. Sold individually, will have undamaged excellent threads. Ford master part number C9ZZ-65222A56-A.  *Note will not have original plastic bushing inserts installed. You will need to reuse your originals or purchase new or used. Please see related items. Stamped with C9ZB-65223A00-A, Ford MPC part # C9ZZ-65222A56-A.Same left and right, 4 required per car (2 per...

Bracket or flat piece of channel for the sliding part of the window regulator Right and left interchange. One per door, screws are included. Also used on early bonded design (glue in glass) in 1970. Attaches to the rear bracket with machine screws. Identified by the countersunk holes for the cross point machine screws. Ford part # C9ZZ-6521504-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our...

This is one of the metal tubes that the windows go up and down on, sometimes called an elevator shaft. Right side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Sometimes marked with a single "R", for right.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521546-A. Do you have questions about Glue-In vs Bolt-In...