C9ZZ-6503406-A Front windshield lower moulding retainer clips. 7 clips required per car, sold individually.

Windshield washer hose clip that holds the hose up under the cowl. Concours quality

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Found on the lower radiator core support.  4 clips needed to attach the wiring harness and the vacuum hoses for the headlight system. Sold Individually. Replaces Ford part # 383104-S.

New reproduction wire loom clip for the lower radiator core support.

Found on the lower radiator core support. 4 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part # 383104-S.

This small detail item is used to hold the console wiring harness to the driver side of the rear console compartment end. It clips to the top of the panel part # C7ZB-65060A74-A . Not for use with the XR7 console.Ford part number C3SB-14A163-B.

Located behind the dash to the right of the steering column.

Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

Door panel clips for the 1967 Standard or XR7. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.

Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is only found on 1969 and 1970 cars.

Used black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.

Used black plastic clip that goes onto the lower center of the firewall of any 1969 Cougar or Mustang. Also found on the back of the instrument cluster on the 71 - 73. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is...

Set includes ten rectangular clips with pop rivets and two incorrect, irregular shaped end clips (Mustang Part). These clips will fit the 68 Cougar, but are actually replicas of the clips for the 67-68 Mustang. Rather than the plastic end clips in this kit, we recommend the metal version that we sell separately. NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to...

Fits 1967 and 1968 Standard or XR7

This is the sub-kit you would have received when you purchased a stainless steel service replacement deck moulding for your 1967 - 1970 Mercury Cougar. The original clips used with a 1967 - 1968 aluminum deck lid moulding would have been similar but would have had a plastic shell surounding the metal clip. For more insight on this tricky trunk trim, check out our video below: ...

Fits 1967 and 1968 Standard or XR7. This kit is nothing more than common door panel clips instead of the correct, unique 1967 A pillar pad clips or 68 A pillar pad clips . These can be made to 'work', but we highly recommend ordering the correct used clips.For the Correct 1967 A pillar pad clips, click here.For the Correct 1968 A pillar pad clips, click here. ...

Fits 1968 - 1973 Standard or XR7

Reproduction Console Ashtray Bumper for the 1967 Mercury Cougar or Ford Mustang.

Fits 1967 and 1968 Standard or XR7

New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.

Reproduction Convertible Brake & Fuel Line Clamp Kit for the 1970 Mercury Cougar - 1970 Ford Mustang 

Reproduction Convertible Fuel Vapor Line Clamp Kit for the 1970 Mercury Cougar - 1970 Ford Mustang 

Reproduction Coupe Brake and Fuel Line Clamp Kit for the 1970 Mercury Cougar - 1970 Ford Mustang 

Reproduction Coupe Fuel Vapor Line Clamp Kit for the 1970 Mercury Cougar - 1970 Ford Mustang 

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

Sold individually Zinc Dichromate (yellow-rainbow)

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash. We think that it is Ford part number 382184.

Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S

Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S

This kit is a must when redoing the disc brakes on a 1968-73 Cougar. Includes new brakets (caliper stabilizers), bolts, pins, and clips and rubber dust seals. Kit includes the pair. Check out this video

Sold individually Zinc (dark silver)

Replaces Ford Part #C7AZ-6243629-A. Not used on 1967-78 trunk locks.

Bulk pack of 100 oval head phillips screws for door and window crank handles.

Fits Standard and XR7 Sold as a Set as Pictured.

Sold individually Zinc (dark silver)

Sold individually. Phosphate & Oil (gray-black)

Fits Standard and XR7

These reproduction door hinge bolts are for the Mercury Cougar and Ford Mustang and fit both standard and XR7 Cougar. They are sold in a set of 24.Intended for the 1968-70 hinges that are stamped steel, and not cast iron like 1967 hinges.

Sold individually. Zinc (dark silver) finish.Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.

Reproduction Door Speaker / Courtesy Light Loom Clip for the 1967 - 1968 Mercury Cougar or Ford Mustang

# 56350-S

Bolt that attaches engine mount to block. 4 bolts per engine, used on all v8 engines Mercury Cougar and Ford Mustang 1967-68. Sold individually.Ford number 304668-S2

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Reproduction course threaded eye bolt for the leaf springs on the 1967 Mercury Cougar or Ford Mustang.Sold individually

Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.