Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Reproduction intake manifold nut for the 289 or 302 on the 1968 Mercury Cougar and Ford Mustang (and possibly other Ford / Mercury cars). 5/16-18 X .72 X .33 zinc free-spin flanged nut. Sold individually. Replaces Ford part #: 374031-S
Ford Part # 379390-s Sold individually
Includes a pair of chrome screw adjusters, nuts and washers, heavy duty plastic rest plates and attaching screws to repair or replace that missing seat back adjustment.Replaces Ford Part #: C1DZ-6461643
Fits 1967 Standard or XR7
This screw / stud seems to always be missing. This screw is just a little longer than stock to accommodate installing the Hi-Po air cleaner. Fits most Autolite carburetors. Size: 4 1/8 inches length 1/4-20 X 5/16-18 threads. Check your thread size on the carburetor, we think that starting in 1969 the Autolite 4300 carburetors had 1/4-20 threads. Please note that this stud has 5/16-18 threads going into the carburetor. Replaces Ford Part #: 370971-A *Note - Check your carburetor, it will...
Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)
Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Sold individually # 374212-S
Fits 1967 and 1968 Standard or XR7
Replaces Ford Part # 50828-S Sold individually. Zinc Dichromate (yellow-rainbow)
Sold individually. Stainless Steel
Barrel nut for the 3/16" stud found on the 6.5 Liter badge and the GT badges that mount on the fender of 1967 Mercury Cougar and Mercury Cyclone GT with the S code 390 engine. Same GT badge on the 1968 Mustang GT models. Item sold individually. The install is basically the same as shown here: https://youtu.be/mcd788WUNns
Reproduction Battery Tray Bolts & U Nuts for the 1968 Mercury Cougar / Ford Mustang
These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.
Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.
Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!
Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!
Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.
Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.
Sold individually Zinc (dark silver)
Replaces Ford Part # 43260-S Sold individually
New screw with a correct 3/8 inch hex head for installing all armrests for all years.
part# 372434-SSold Individually.Head size: 5/8"Thread size: 7/16"
Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).
Not a concours correct head pattern, but it looks good. Bright cadmium finish. 5/16-18 x 7/8 long.
Replaces Ford part # 385664-S
Used front crossmember bolt for the Mercury Cougar or Ford Mustang. It is crucial that you use this correct tapered bolt when installing the front cross member.
Reproduction zinc front shock bolt with correct anchor symbol on the head, just like the originals.Sold individually.
Sold individually, pivot stud for the aluminum power steering pump mounting bracket. fits all applications for small or big block. Also used on the 1970 Mercury Cougar with 428CJ. Phosphate & Oil (gray-black)
Rear valance and 1967-70 windshield defroster attaching hardware. Sold individually. Zinc (dark silver)
Good used original seat belt bolt. There were a few different variations of this bolt, some were stamped with a D with triangles, some with E and three triangles and others had no stamping at all. 13/16" hex head, two inch bolt with a 7/8 inch shoulder.
Front retractor bolt, used in conjunction with two rubber spacer / washers and one washer. The two rubber washers go on either side of the re-tractor mounting hole and the metal washer is against the inner rocker.
Front inner bolt that attaches female portion of the lap belt to the transmission tunnel. Used in conjunction with a silver, fat washer that is slightly cupped.
Inner front bolt, long length to clear sound deadener. Used in conjunction with a thick, gold spacer washer.
Used early version of the long seat belt bolt for the Mercury Cougar or Ford Mustang. This early version has faint markings on the head of the bolt as where the later versions have more prominent markings. 13/16" hex head, two inch bolt with a 1/2 inch shoulder. Can be either smooth headed or have an "E".
Used early version short seat belt mounting bolt to mount the front retractor to the inner rocker panel and used in conjunction with a large washer. This is an early version of the the seat belt bolt with faint or no markings on the head, the later versions are longer, and have much more prominent head markings.13/16" hex head, 1-1/8inch bolt with a 3/16 inch shoulder.
Rear seat belt bolt, four per car used in conjunction with two red washer / spacers. 13/16" hex head, 1-1/4 inch bolt with a 3/16 inch shoulder. Strong "A" on this one as shown. There is another version of this same bolt with a light "A" or smooth head and no markings. See related items.
Used to mount the front retractor to the inner rocker panel. Used in conjunction with a large washer. 13/16" hex head, 1-1/2inch bolt with a 1/2 inch long shoulder. May or may not be marked with a letter "C".
Good used original seat belt bolt. There were a few different variations of this bolt, some were stamped with a F and others had no stamping at all. 13/16" hex head, 1-7/16 inch bolt with a 1/4 inch shoulder.
Reproduction water pump bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These are zinc (dark silver) plated and sold individually. This bolt is approximately 2-5/8" to the shoulder and an approximate overall length 2-3/4".
Replaces Part # C9OB-3B284. We also have this bolt available in fine thread but only as a used bolt. Four required per car. Sold individually
Reproduction water pump / timing chain cover for the Mercury Cougar or Ford mustang equipped with the 289 engine. This bolt has an approximate length of 2" to the shoulder and an approximate overall length of 2-1/4".
This is the shorter version of the top-loader with no "+" on the head. Sold individually
Reproduction Upper Control Arm To Shock Tower bolt. Sold individually. Replaces Ford part # 38049-S
NOS water pump bolt for the Mercury Cougar or Ford Mustang. This bolt is approximately 3-1/2" to the shoulder and an overall approximate length of 3-3/4".Replaces part # 376258-S.
Ford part #300958-S Sold individually
Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually.