Body

Trunk lock cylinder retainer for all 1973 Mercury Cougars, different retaining configuration from 1971-72 Cougars. The MPC does not show the part number but it is likely D3WY-6543629-A. Mustangs used a different retainer with a Mustang part number.

Good grade "A" used nut with minimal scratches from removal process. The originals have deeper grooves and have a better luster on the chrome than the reproductions. This is a one year only design. Don't forget to check out our special tool used to remove and install this nut.

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Reproduction roof repair kit that includes the roof skin, C pillars and the rear window channel for the 67 - 68 Mercury Cougar. C pillars are cut from our reproduction quarter panels. This kit must ship via truck freight. Expect to pay $400 or more to have these items shipped. Our online shipping calculator is not very accurate for truck freight items so we encourage you not to pay for the order up front but rather bypass paying for your order by selecting "contact us for...

Companion reproduction insulation for our premium 1969-70 Mercury Cougar sail panels. These were created by a Cougar enthusiast for Cougar enthusiasts. Copied from an original 1969 Cougar Eliminator. Sold in pairs, originally held up with a bit of spray adhesive glue. Same thickness heavy felt as originals.

Reproduction white rear interior sail panels for 1970 Mercury Cougar XR7 and standard models with courtesy light provision. Reproduction rear interior sail panels made from hard backer board, covered in textured white vinyl with embossed border. Original panels were made of textured paper. Metal reinforcing ring installed for courtesy lights. Several different versions of courtesy lights were used 1969-70. These allow the installation of the chromed reproduction courtesy lights which look...

Reproduction rear interior sail panels for 1970 Mercury Cougar XR7 and standard models with courtesy light provision. Reproduction rear interior sail panels made from hard backer board, covered in textured black vinyl with embossed border. Original panels were made of textured paper. Metal reinforcing ring installed for courtesy lights. Several different versions of courtesy lights were used 1969-70. These allow the installation of the chromed reproduction courtesy lights which look great...

Uncommon jack as identified by the coarse threads. This version was made by a specific supplier AUSCO or Auto Specialties Manufacturing Company. AUSCO supplied jacks to Ford until 1970.See the link for the Ford jack research done by Marcus Anghel - Anghel Restorations

Original scissors jack. We save the working ones that come to our yard. Hinge points should get little oil or a quick spray of WD-40. Wipe down the residual grease and oil and stow it in the trunk again! Notice the correct placement of the instruction decal. That's the tip of the day! *NOTE* There are multiple versions of this jack that differ in the area that makes contact to the rocker and the thread pitch. We will be sorting out those differences and posting our findings here soon. ...

New and improved reproduction bottom of the door seal for the 1967 - 1970 Mercury Cougar or Ford Mustang. Unlike previous versions, these are now made with denser material and are much more rigid. They measure 38" for 1967 -1968 and 41" for 1969-70 so you will have to trim them down if you have a 1967-68. One of the most common missing parts on a 1967-70 Mustang or Cougar today is the lower weatherstrip seals on the doors. These seals were added to cars to keep dirt and moisture from entering...

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

Published by the Lincoln Mercury Division to provide information on diagnosis, service procedures, adjustments & specs. Filled with diagrams and illustrations to help disassemble, repair & reassemble various components pertaining to the sunroof panel on the 1968 Mercury Cougar.Issue # LM-7882April 1968

This tower is identical to every other 1967-70 tower in every way except the reinforcement plate.The reinforced shock towers came out in late March 1968 and were used on all big block Cougars and Mustangs. 390-2V / 390-4V / 427 / 428CJ. No specific part number exists for this structural front suspension section with or without wrap around bracing. This example was actually taken from a very early 1969 San Jose built Cougar and is identical to the late 68 Big Block Tower. The only reason you...

This tower is identical to every other 1967-70 tower in every way except the reinforcement plate. In late 1968 390-427-428 Mercury Cougar and Ford Mustang came with this reinforced tower due to a problem they were having with structural cracking. No specific part number for this structural front suspension section with or without wrap around bracing. This example was actually taken from a very early 1969 San Jose built Cougar and is identical to the late 68 Big Block Tower. The only reason you...

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

Here is a real treat! New in the Ford box driver side (left hand) mirror, very hard to come by these days. *NOTE* XR7 and GT Cougars ordered with a "special paint" color got this chrome mirror in place of the color keyed sport mirror that came standard with those option packages. A small credit was given for the trade down and was shown on the invoice. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Very nice pit free mirror worthy of a low mile original car.*NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere!Hole spacing: 4 3/8"Ford part # C7WY-17696-ADo you have riv-nut questions? Here are riv-nut answers! ...

NOS unpackaged driver side manual adjust mirror. Shows some shelf wear, a small scuff on the base and a smudge on the glass. Don't forget to select a mounting gasket and mounting kit if needed. Casting number reads C7WB-17743-B Ford part # C7WY-17696-A. *NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere! Hole spacing: 4 3/8" Do you have riv-nut questions? Here are riv-nut answers! ...

Grade A mirror will have no cracks, deep scratches or pits. Will look right at home on a low mile garage kept car.

Working driver side (left hand) grade "B" remote mirror with dull chrome. Don't have too high of expectation on this, it is 40 years old and comes from a car we most likely pulled from a brier patch...

Working grade "A" driver side (left hand) remote mirror with nice chrome. This would look right at home on a low mile unrestored car. Hole spacing: 4 3/8"Do you have riv-nut questions? Here are riv-nut answers!

Good working grade "A" driver side (left hand) mirror that will look as good as the one shown here. Since the wand is recessed into the door panel on the 1969 Cougar, the wand is not prone to breaking off like the 1970 version which protrudes straight out. NOTE - Cable length should be 18" from the base of the mirror to the inner end of the remote wand assembly. In order to keep the cable from hitting the window, there's usually a clip to hold it away from the glass. This clip is hard to come...

The wand will be intact on this grade "A" driver side (left hand) remote mirror and the chrome will be free of pits. Notice the 1970 mirrors differ from 1969 in that the wand exits the door panel at a 90 degree angle. Rarely do we have a mirror this nice but you can get in line for the next one that becomes available by selecting the "notify me option" and we will email you when one comes in. There is no passenger side mate to this mirror or any chrome mirror found on a 69-70 Cougar.Ford part...

This used grade "A" remote mirror has chrome that looks great and the adjustment wand is unbroken and working. Used on the drivers side of standard Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A will be supplied.Replaces Ford part numbers D1WB-17743-AA and C9AB-17743-A.Do you have riv-nut questions? Here are riv-nut answers! ...

Good working grade "B" driver side (left hand) mirror that most likely will not have as good of chrome as the one shown here. Since the wand is recessed into the door panel on the 1969 Cougar the wand is not prone to breaking off like the 1970 version which protrudes straight out. NOTE - Cable length should be 18" from the base of the mirror to the inner end of the remote wand assembly. In order to keep the cable from hitting the window, there's usually a clip to hold it away from the...

This used grade "B" remote mirror has chrome that looks shabby, adjustment wand is unbroken and working. Used on the drivers side of standard Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A will be supplied.Replaces Ford part numbers D1WB-17743-AA and C9AB-17743-A.Do you have riv-nut questions? Here are riv-nut answers! ...

This NOS remote mirror came to use without a Autolite or Motorcraft box. Current offering while new and never installed does have a small manufacturers defect in the casting as shown. Found on the drivers side of standard model Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A. This mirror has the Ford casting number D1WB-17743-AA. Do...

Used driver side (left hand) grade "A" manual side mirror for the Mercury Cougar. This is your plain Jane manual adjust mirror for the driver side of your 1969 or 1970. Uses same base mounting pad as all 1969-70 Cougar driver side mirrors.Ford part # C9WY-17696-B. Do you have riv-nut questions? Here are riv-nut answers! This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Used driver side (left hand) grade "B" manual side mirror for the Mercury Cougar. This is your plain Jane manual adjust mirror for the driver side of your 1969 or 1970. Worn finish, scratches, often will have light pitting. Uses same base mounting pad as all 1969-70 Cougar driver side mirrors.Ford part # C9WY-17696-B. Do you have riv-nut questions? Here are riv-nut answers! ...

Used manually adjustable grade "B" side view mirror for the Mercury Cougar Standard or Ford Galaxie. This ambidextrous mirror can be installed on either the passenger or driver side door. This good used mirror will have good glass and will have some pitting in the chrome as shown. Also used on various 1967-73 full sized Ford and Mercury cars. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8"Base Length: 6-5/8"Overall Height: 5-1/8"Mirror Width: 5-1/8"Mirror Height: 3-5/16"...

Fine scratches but great for the guy who wants original. The Reproduction does not have the II-DMI-6 lettering at the bottom like this original. You will have to carefully peel (roll back) the aluminum backing that is glued in place before gluing it in your mirror. If you use needle nose pliers and take your time it usually works fine. Note that the pictures of our 67-68 mirrors and lens can be deceiving. This is a tapered mirror, the narrow end faces upward on a Cougar, it is reversed when...

Rare find. The difference between this and a 69 is the 90 degree angled portion that mounts to your door panel. This is correct for a XR7 or Eliminator. The 1970 sport mirror did not use a chromed base at any time. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

This plastic fastener is used to keep your mirror cable from interfering with the movement of your door glass. It is located at the front of the door near the top.

Ford Casting number as seen on the bottom side is D0OB-17713-AW. Many people misinterpret it as D00B-17713-AW, D00B-17713-AW or DO0B-17713-AW. Perfect base with no cracks or bends. The Pastel Blue base is from a 1970 and the Red base from a 1971. Even when placed side by side it is hard to tell the difference. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Complete Service part mirror assembly for any Cougar with the sport / bullet racing style mirror. Casting number as seen on base is D1WB-17743-B.Ford part number D1WY-17682-A

This mirror features a painted base which was used on the Sport Special and Eliminator models. XR7 models used a chrome base except the very late cars. Good used mirror ready to be painted and installed. We test the remote function before we send. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Ford Casting number as seen on the bottom side is D1OB-17713-AWA. Many people misinterpret it as D10B-17713-AWA, DI0B-17713-AW or Dl0B-17713-AWA. Perfect base with no cracks or bends. Visually it is impossible to tell this part from 1970 with a D0OB-17713-AW casting number on the bottom. The Pastel Blue base is from a 1970 and the Red base from a 1971. Even when placed side by side it is hard to tell the difference. Do you have questions about installing a passenger side mirror or using...

NOS passenger side (right hand) sport mirror that is correct for the Mercury Cougar. This will also work on 1969-70 Cougar, but base height is just a little bit taller. Replaces Ford part # D1OB-17713 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video Check out this video ...

Used passenger side (right hand) sport mirror that is correct for the Mercury Cougar. This will also work on 1969-70 Cougar, but base height is just a little bit taller. *NOTE* We are currently out of good used mirrors with original bases so if you order this part you will get an original mirror with a reproduction base. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video Check out this video ...

We do not currently have any used units in stock, but we often place items like this on our site for documentation purposes. We hope to have a reproduction of this item soon. Do you have riv-nut questions? Here are riv-nut answers!

Original space saver tire marked F78-15 from a 1970's Mercury or Ford. GoodYear brand it has the larger hub size, bolt pattern is 5 on 4-1/2. Not sure if it has ever been inflated, it is collapsed as shown.  Just looking for a space saver spare? This is it, it looks the part to those that casually look in the trunk of the car at a car show. Tread is period correct for a Goodyear tire, but typically B.F. Goodrich was optional on 1968-69 Cougar or Mustang. *NOTE* Does not include...

Nice unused space saver spare tire for a Ford. Vintage Good Year brand tire with size F78-14. BF Goodrich is another common brand of tire installed for use with unique storage location, hold down, and inflation bottle. This one does not appear to have been inflated or used on the road. Still has the nubs on the face of the tire as shown.

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Used original rear spoiler as taken from a 1969 Eliminator. The 69 wing was lighter and much more prone to cracks and sagging as in 1970. This one was taken from a parts car and properly stored indoors since 1991. Impossible to find in this condition. SEE ABOVE PHOTO FOR INSTALLTION MEASUREMENTS AND DIMENSIONS.Ford part number C9WY-6544206-A

Used original rear spoiler as taken from a 1970 Eliminator.Ford part number D0WY 6544210-A Ford casting number C9WY 6544210-A

Used manually adjustable grade "A" side view mirror for the Mercury Cougar Standard or Ford Galaxie. This ambidextrous mirror can be installed on either the passenger or driver side door. This good used mirror will have good glass and nice chrome for your restored or nice original Cougar or Galaxie. Also used on various 1967-73 full sized Ford and Mercury cars. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8"Base Length: 6-5/8"Overall Height: 5-1/8"Mirror Width:...

Quality reproduction stone guard for the 1969 Cougar. This unit is also known as a bumper filler, rock guard, or filler panelReplaces Ford part # C9WY-17779-A.