All Available Parts - 1967 Mercury Cougar

Good used center reinforcement beam, or structural brace section for the roof skin. It does not actually attach to the roof skin. Attaches to unitized structure of the roof frame sides. Ford part number is 50222, or 6550244.

Reproduction wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

We ask that you call us on this one. Roof cut includes the roof skin, 'A' pillars cut about 4 inches from the top, rear or 'C' pillars cut below the leaded seam. We have plenty of inexpensive, damage free roofs that have never had a vinyl top installed. If you want the pillars intact this triples the size of the crate and makes it cost prohibitive in most cases. Longer cuts with long extended pillars add greatly to the cost of shipping. This is a perfect cut for a Cougar owner looking to...

Reproduction cover board for the rear package tray found on the 1967 Mercury Cougar behind the rear seat, visible through the rear window. The 1967 tray is deeper as it installs over the tops of the rear side panels. In 1968 they installed under the rear vinyl covered panels. The difference between the WCCC panels and the others on the market is that we run them through a drum sander so as to give the textured side a more muted look and feel than unsanded masonite board. The other brands do...

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 682

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the passenger.

Guide that measures 10 5/8" long held in place by the outer trim that has four screws. Driver and Passenger are interchangeable.

This part mates to and is held down by Golde #100 413 681. The Golde part number for the smaller, lower elbow guide is 100 413 664

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

Knob for engaging the emergency flasher switch on a fixed (non-tilt) steering column. This original knob is plastic, the reproductions are chrome plated die cast.

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

Good used part without excessive rust or damaged rubber. For use with fixed column only.

Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

Reproduction rag joint for the fixed steering column in the Mercury Cougar or Ford Mustang. This assembly is for the fixed column only and will not work for the tilt / tilt away steering column. Our reproduction rag joint comes assembled with the lower splined casting. 

12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.

Bare outer tube for the 1967 Cougar or Mustang tilt steering column. This item will be free of major rusting and will have to be painted to match your car. Keep in mind that these tubes are specific to each year. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Check out this video ...

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

[No Description Provided]

[No Description Provided]

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place.  Ford part # D1AZ-3518 or E2AZ-3518

Reproduction Chrome / Black Leather steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and walking cat center decal. Hardware included.

Reproduction Chrome / Woodgrain steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Dark Mahogany Woodgrain steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Black Steel / Black Leather steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction thick grip Mahogany Woodgrain / Chrome steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Black Leather four spoke steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Easy screw in replacement with correct chrome finish. Made in chrome die-cast, originals were plastic. The tilt column switch uses a deeper stem. Replaces Ford Part #: C7OZ-17513-A

Emergency flasher switch bezel for the side of fixed steering columns (non-tilt). For all years 1967 1968 1969. Paint to match your interior. Compared to the reproduction version of this bezel, there is a difference. "Emergency Flasher" lettering is much heavier on the originals, plus they came color matched to the steering columns. We can often times supply your desired color, please include color needs in the comments section. Ford part number C9OZ-15C580-A.

Used emergency flasher knob for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. These knobs are very fragile and the chrome plating will show some minor scratches and pitting. We try and keep these on hand, but the fragility makes them 'subject to availability'. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down...

Used vacuum release valve for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This vacuum solenoid releases the steering column for the swing away function. These vacuum tilt solenoids are tested and guaranteed to work. Bench testing the 1967-69 tilt away release solenoid: Verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to...

Used wire extension for the tilt / tilt away steering column found in the Mercury Cougar or ford Mustang. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts needed. To offset the cost of your rebuild, you can send us additional parts or parts columns and we will give...

One year only part not found on any other car except Cougar and Mustang with tilt. If you would like to run a 1968 or newer steering wheel on your 1967 then you need to exchange this cover with the version found on the 1967 Thunderbird which has no lip at the top. We have these in stock and would enthusiastically trade it for the Cougar / Mustang upper cover. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This Thunderbird collar is a good substitute for those wanting to put an after-market or 1968 up steering wheel on their 1967 Cougar / Mustang. We also suggest purchasing this collar when installing our reproduction 1967 Mustang deluxe steering wheel.  *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Ninety degree bracket needed to mount the starter safety switch to the column tube in 1967.

Used steering column release rod which is attached to the vacuum motor and lock pin, and also pushes the neutral safety switch.

This reproduction radiator support crossmember is correct for the 1967-68 Mercury Cougar and Ford Mustang, but will work on any 1967-70 Cat or Pony.Replaces Ford # C7ZZ-6510852-B or C9ZZ-6510852.

Reproduction radiator / core support for Mercury Cougar and Ford Mustang. This is the very best one made! Replaces Ford part # C7ZZ-16138-B and C7ZZ-6510852-B together.

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install.  These are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available...

This clip fastens the vacuum motor to the locking pawl rod. One required per car. Fits 1967 Ford tilt-tilt away columns only. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired.

Used locking pawl for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. This pawl is released and via the vacuum motor when the door is opened and the ignition is in the off position. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...

Used locking lever for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. Two required per car. Here is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange.  *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used to mount the vacuum actuator to the column in 1967 and the actuator to the bracket on 68-69. Also used to mount the steering column relay and vacuum release valve in 1968-69.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last...

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used cap for the index lever tension spring for the Mercury Cougar or Ford Mustang equipped with the tilt/tilt away steering column. Two required per car.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place.  * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

Mates vacuum nipple on white plastic vacuum motor to ninety degree metal elbow.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used tilt / tilt away column shaft for the Mercury Cougar or Ford Mustang. Inner shaft with tight U-joint and perfect steering wheel mounting threads. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Two required per car, early 67 used a chrome version of this screw. Later years used this screw.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used pin for the locking lever in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Two are required in 1967-69, but only one is required for 1970 and up. Recommend changing to a up dated version of this pin with one that has circlips or snap rings (15-0156 for 1967 -69 or 15-0157 for 1970-1973) *NOTE* For tilt column service, you can contact Tony...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 1968 1969 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse your existing 12 point bolt for the other end or purchase a second one. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is...

Used release lever for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is sometimes also called a bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used spring cap that is used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used pivot cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Don't try to straighten your rod if it looks like this. The contour seen here is correct. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Emergency flasher switch bezel for the side of fixed steering columns (non-tilt). For all years 1967 1968 1969. Paint to match your interior. There is a slight difference between the original bezel and these reproductions. Original bezels have taller "Emergency Flasher" lettering, plus they came color matched to the steering columns. Functional reproduction item. Ford part number C9OZ-15C580-A.

Identified with the straight bracket compared to the 1968 relay which has a bend. These relays are tested by our electrical department. Keep in mind we have a reproduction substitution for this part. Ford part # C7ZA-3E553-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. This icon means that we're looking to buy this part!WCCC...

Used steering column flange bumper for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This little unit is made of plastic and Ford used it to keep the tilt / tilt away steering column's flanges in the knuckle assembly from breaking its self apart during actuation. Because of the forces generated in the tilt / tilt away column's actuation, your knuckle assembly will fail due to metal to metal contact if this piece is missing. Ford part # C7SZ-3D565C....

Used steering column tube retainer for the 67 - 69 Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. These little units help hold the steering column together and there are 3 required per column. Sold individually. This are not advisable in the 1970 and later cars. Ford part # C7SZ-3499-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used tilt / tilt away steering column converted into a tilt only unit for the Mercury Cougar or Ford Mustang. All 1967-69 Cougars and Mustangs optioned with a tilt column also had the tilt-away (aka tilt-swing, tilt-fly or tilt-pop). There was never a tilt only option in 1967-69 Cougar or Mustang, no matter what you may have been told... That being said some of our customers prefer not to have the added expense or complexity involved with the swing-away function. This column has been fused at...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used lower knuckle for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This knuckle is unique to 1967 because the center hole is round. The 1968-69 features an elongated center hole.  There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* We'll give you UP TO $100 cash back for your...

Used Emergency Flasher Knob Bezel / Fixed Column for the 1967 - 1969 Mercury Cougar / 1967 - 1969 Ford Mustang 

Used black plastic clip for holding the turn signal wiring harness to the column tube, next to the vacuum actuator. Fits any 1967 Mercury Cougar or Ford Mustang with tilt swing away steering columns.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Locking pawl catch pin for your 67-69 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break...

Reproduction steering column flange bumper for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This flange is made of a material known as UHMW, or Ultra High Molecular Weight plastic. This material has been used by NASA for many parts that were formerly made of nylon. This material is five times stronger than nylon, and has a much higher impact rating. Compared to the original nylon part, this piece should not have to be replaced for a good number of...

Used tilt column wiring harness for the 1967 Mercury Cougar. 

Reproduction of the upper steering column bearing for your 67* - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. You can find the lower bearing here. Outside diameter: 1 3/16 " Inside diameter: 15/16 "Thickness: 1/4" Replaces Ford Part Numbers: F23Z-3517, C1AA-3517-A, C3AZ-3517-A, C7SZ-3517-D, D0AZ-3517-A, F23Z-3517-B * - may not fit some 67 Mustang applications with a fixed column as these used Ford...

Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

This is a tension spring that defaults the steering wheel to up and or tilt away position. The spring in the 1967 Column is not as strong nor as tall as the 1968 or 1969 column spring.Spring Length: 2 5/16" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1967 tilt-away steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This Screw fastens the plastic guide for turn signal wires next to column under the cone by steering wheel.

One year only bracket used on both fixed and tilt column cars.

Reproduction pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and 2 - 4 are required per car. Pin is custom made on short runs and is very difficult to find. .001 undersized, and with 8/32 threads instead of 6/32 like the originals. Newer pin removal tools will fit. Replaces Ford part # C7SZ-3D739-A. Removing pivot pins on 67 - 69 tilt away columns: Work on the upper knuckle pivot pins as there is room...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used Transition cover for the 67 Cougar or Mustang tilt steering column. This flange is different from 68 - 69. The 1967 flange does not have an inner tube to bolt to. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Reproduction vacuum reservoir for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This is a 1967 only design that didn't have mounting bolts on top like the later versions, they used a side mounting bracket.NOTE: You will need to use the mounting bracket from your old can, these reproductions do not come with one. *NOTE* WCCC services all FoMoCo tilt...

Used turn signal switch connector for your 67 Cougar or Mustang. Work with either tilt or fixed columns. This is the connector that attaches the turn signal switch to the main dashboard wiring harness. OEM was a white colored plug,the Scott Drake reproduction is black.. 

C7ZZ-652220-B Restored, stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Passenger side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible.

Restored passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. This part has been "bright dip" anodized just like original and will not turn a chalky white color in a few months like one that has been polished only. Cores with minor dings or scratches are what is needed, smashed or folded trim parts cannot be restored. We are pretty liberal about these rear core exchanges, if you do not have a core, a similar core from a 1967-70 Cougar will usually suffice...

Restored driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. We have many NOS trim parts in stock, but why bother when you can get correctly restored parts for less? This part has been "bright dip" anodized just like original and will not turn a chalky white color in a few months like one that has been polished only. If you select this option (paying a core charge), we will randomly select mouldings off the shelf. Paying the core charge does not mean you will...

Restored aluminum rear deck lid moulding / trim for the Mercury Cougar. If you do not have cores that are worthy of restoration we do have them for sale. The better core you start out with, the better the end result will be! If you prefer a mirror like luster then I suggest you purchase the 1969-70 deck moulding as stainless offers a much brighter finish. Seven clips are used to install the deck lid moulding and we have new clips available here. We will accept extra cores in on exchange for...

Restored three piece anodized aluminum rear moulding / trim set for the rear of the 67-68 Mercury Cougar. These pieces attach to the rear deck / trunk lid and the quarter extensions. New and used clips also available separately. Ford part #: Driver side quarter extension moulding C7WY-6529313-A, passenger side C7WY-6529314-A, deck lid moulding C7WY-6542512-A. If you select this option (paying a core charge), we will randomly select mouldings off the shelf. Paying the core charge does not...

Used passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches or corrosion. Perfect for your daily driver that is in above average condition.Ford part # C7WY-6529314-A.

Used driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. Good used driver quality moulding / trim with no obvious dings, deep scratches or corrosion. Perfect for your daily driver that is in above average condition.Ford part # C7WY-6529313-A.

Used clip for the adjustment tension spring for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...

Lower steering column mounting bracket. 1967-68 Mercury Cougar and Ford Mustang. Right and left halves with original fasteners. Rubber gasket sold separately.Ford part number C7ZZ-65017A50 and C7ZZ-65017A51.

Core passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. Good trim part that is ready for restoration or could be used on a driver.Ford part # C7WY-6529314-A.