1967 Ford Mustang

This 24" radiator has four rows of cooling fins. From the factory there were only 2 or 3 rows. Whereas an additional row of fins does offer more cooling surface and raises the coolant capacity, we find the benefit is diminished by the fact that the shroud no longer fits well and the fan will be positioned too close to the radiator and does not fit well where the bottom tank meets the core support on some applications. *NOTE* We do not accept returns on four core radiators.For some helpful tips...

This is the heavy duty cooling brass core radiator for the big block cats for 1967 - 1970. It also fits the 1970 with the 351C or 351W with Air Conditioning, or the need for heavy duty cooling. Note that the 67 390 Cougar actually used a slightly narrower radiator then this one. If you install this in a 67 you will need the 68-70 lower mounting brackets and a 68-70 shroud. *NOTE* We do not recommend using a four core as it makes fitting the original shroud very difficult, places the fan closer...

Reproduction radiator / core support for Mercury Cougar and Ford Mustang. This is the very best one made! Replaces Ford part # C7ZZ-16138-B and C7ZZ-6510852-B together.

Radiator side block off plates, or radiator filler panel, for the 20 inch radiator found on standard cooling and non-air conditioned Mercury Cougar and Ford Mustang 1967 - 1968 all engines. Two per car, one on each side of the radiator. Sold individually. *NOTE* Block off plates not needed with the 24 inch radiators.

New 13 Pound Generic Radiator Cap with Safety Release for the 1967 - 1973 Mercury Cougar / Ford Mustang

New old stock Chrome radiator cap. Motorcraft stamped, with RS-512A, and 13# Pound rating is stamped on cap. Replaces Ford Part #: C9ZZ-8100-A.

Keeps the corrosive agent in your coolant from destroying vital engine components

These concours quality Zinc caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

BECAUSE THIS IS NOT AN ORIGINAL FORD PRODUCT, WE CANNOT RECOMMEND THIS ITEM AND NO RETURNS WILL BE ACCEPTED Shroud assembly includes custom mounting, wiring harness, and adjustable thermostat. High temperature resistant plastic with high performance electric fan to produce maximum cooling efficiency. This unit will also increased fuel economy and horsepower.  2550 CFM Fan with 30 AMP draw.  Dimensions (in inches): 15 3/4 x 26 1/2 x 3 7/8  including mounting flanges on...

Four needed per fan shroud. While not technically correct, some like the black screws over the silver because it better matches the radiator and shroud. Hexwasher Head #14 X 5/8 Tapping Screw Ford Part Number: 31498-S

Four needed per car. Ford Part Number: 31498-S

Concours bolt for all 1968-70 Mercury Cougar and Ford products including Mustang, radiator fan clutch to radiator cooling fan. 1/2 inch hex head size. Threads are 5/16-18. One bolt with captured split washer. Also available in a set of 4. ...

Reproduction Radiator Mount Kit for the 1967 - 1968 Mercury Cougar - 1967 - 1968 Ford Mustang 

FEATURES : KHE 300-USB Features: * Wireless Bluetooth; * Mini SD Card Reader; * USB Flash Drive; * 6 AM/6 FM Preset; * Manual Up/Down Tuning; * Seek Auto Tune; * Auto Stereo/Mono; * Preset Scan and Auto Store; * Front/Rear Fader Control; * On/Off Volume Control; * Separate Bass/Treble Control; * Left/Right Balance Control; * Auto Antenna Power Lead; * LCD Display with Blue Back Lighting; * Aux Input Rear; * Frequency Selector. Size: N/A * Output: 50 Watt x 4 Channel * System Power: 200 Watts...

Secretaudio SST is a hidden audio system that offers great flexibility for mounting in any type of vehicle. The main receiver/amplifier unit is usually hidden under the seat, or behind the dash. A 10ft cord from the Tuner/Amp plugs into a LCD display. The system can be operated from up to 40 feet away with the included RF (radio frequency remote.) Included with the system is a flush mount bezel for console or dash mounting. The small dimensions of the flush mount system allow you to install...

Nice reproduction 1967 Cougar and Mustang radio knobs for use with factory radios. For use without the console option, these have the later style and knob height. This reproduction knob set does not have any Ford casting numbers and are chromed metal knobs, not plastic. The inner knob on the 1967 AM radio station adjusting dial will need a white sleeve our part number 10022230. Factory radios with fader control will not need the sleeve.If you want to use these knobs on your 68, they will work...

Note: Not for use with aftermarket radios. Finding correct radio knobs for a 1968 Ford Mustang or Mercury Cougar equipped with a center console has been a huge obstacle for decades now. To clear the padded radio bezel cover, one must have these elusive, one year only, deep well knobs. These will also work on 1967 Cougar with console and although they would not be letter correct for anything but a 68 with a console, they do not look out of place on a 67 with console. Note that this four piece...

This is a radio nut removal tool used to remove the radio shaft nuts. No more trying to remove those little units with the wrong tools and potentially damaging your bezel or dash. These are made from HRS steel and are milled to fit the shaft nut perfectly.

Correct plug for your 1967 - 1973 Mercury Cougar or Ford Mustang. Often these have been cut from the main loom to install an after market radio.

Reproduction radio plug and pigtail for your 1967 - 1971 Mercury Cougar or Ford Mustangs.

These anti static devices were installed under the front bearing dust caps on cars equipped with factory installed AM-FM radios. The part pictured is NOS, the one we currently have in stock is used. Sold individually.

This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...

C6OA-18832-A is the number stamped into the end of the Autolite capacitor. Attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. Application all Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory.. Starting in 1972 there is a Motorcraft version...

Good used part without excessive rust or damaged rubber. For use with fixed column only.

This polyurethane steering coupler repair kit for your tilt column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. Some customers feel polyurethane improves steering feel. Replaces factory steering coupler on 1967 - 1973 cars. Most 1967 Mustangs with fixed steering columns do not have coupler.Replaces Ford Part #: C7OZ-3A525 Check out this video ...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 1968 1969 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse your existing 12 point bolt for the other end or purchase a second one. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is...

New old stock power steering ram cylinder boot, rubber boot only. Fits all 1967-70 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C3AZ-3C651-A.

This new reproduction power steering ram cylinder is good quality with almost no warranty claims. However, When you go to put your cotter pin in the castle nut you will often find it does not align perfectly which means you may have to drill it for a perfect fit. Keep in mind we will pay $30 in in-store credit for a clean original used ram cylinder so don't throw them away! RAM BOOT SOLD SEPARATELY. Replaces Ford Part #: C3DZ-3A540-A or C7ZZ-3A540-A. ...

This an original, rebuilt power steering slave / ram cylinder. It has not had a cosmetic restoration so it will show external dings, scrapes and general wear associated with a 50 year old part located on the bottom of a car. If you buy our reproduction ram do not throw away your core used ram as we often can give in store credit for the part. RAM DUST BOOT SOLD SEPARATELY.Replaces Ford Part #: C7ZZ-3A540-A.

Quality complete rebuild kit, includes all hardware shown. Premium flexible rubber boot that has vent holes, boot for elbow, and all hardware designated by an experienced rebuilder for completeness. This is the best known kit on the market.

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. This economy version of our 8 inch rear end assembly is perfect for those intending to add rear disc brakes to their car.  Spring perches are 43 inches apart on center. Axle...

Reproduction rear axle outer bumper for the Mercury Cougar or Ford Mustang. These units mount on frame rail, are push in and two are required per car. Sold as a pair. Replaces Ford part # C6AZ-4730.

Reproduction rear boot for your 67 - 69 Cougar or Mustang Midland power brake booster.

Replaces Ford Part #: 379670-s

Used trunk or luggage compartment latch, fits all 1967-73 Mercury Cougar and many other Ford and Mercury cars. Comes with 3 bolts for mounting.Replaces Ford part number C5AZ-6243200-A.

Reproduction front diaphragm for your 67 - 69 Cougar or Mustang Midland power brake booster.Diameter 7 1/4"

[No Description Provided]

Passenger side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1967-69 Mercury Cougar and Ford Mustang.

Reproduction driver side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps ...

Reproduction passenger side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps. ...

Fits any model that used the banded Midland-Ross booster. This Bakelite hub can be seen when you remove the dust boot. It is a very brittle fragile part that gets broken when you drop the booster, attempt to bleed the brakes with the engine running or install the wrong brake pedal.

Reproduction driver side rear inner apron for both the Mercury Cougar and Ford Mustang.

Reproduction passenger side rear apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

This is the seal at the back of the booster on the Midland-Ross units.

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...