1967 Ford Mustang

These reproduction fender splash shield bracket screws and J nuts fit both the Standard and XR7.

Set of nuts and Ferrules for thermactor smog tubes on any 1967 S code 390, 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original or reproduction smog tubes. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the smog tubes and other hardware.

Tall style filter for C4 transmissions.  Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.

Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford. 

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Replaceable filter which attaches to original fuel sending unit. Fits 3/8" tube. Replaces Ford part #: D1AZ-9A011-A.

Slightly longer than the original. Replaceable filters which attaches to original fuel sending unit. Only fits the 1967 Mercury Cougar. Replaces Ford part #: D1FZ-9A011-A.Check out the video below on our new gauge tester: ...

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Reproduction black 3D printed brake booster filter retainer for the Mercury Cougar and Ford Mustang. Same functionality at the originals, it fits between the brake booster and master cylinder in the aluminum master cylinder spacer. You can find the filter here.

Reproduction black 3D printed brake booster filter retainer for the Mercury Cougar and Ford Mustang. Same functionality at the originals, it fits between the brake booster and master cylinder in the aluminum master cylinder spacer. You can find the filter here.

Used assembly line, white plastic filter retainer for the Mercury Cougar, Ford Mustang and other Fords equipped with Midland Booster. It fits between the master cylinder and brake booster on the aluminum master cylinder spacer. The repro and service replacement filter covers are usually black not white. You can find the filter here. ...

Reproduction Mercury Cougar and Ford Mustang firewall.Here's our little film to help you fortify your flexxy feline!

This 67 and 68 Firewall To Hood Seal Reproduction has attached rubber studs for mounting. Replaces Ford Part #: C7ZZ-16740.

Rubber plugs for sealing the holes in the firewall of any 1967-68 Mercury Cougar or Ford Mustang. These plug the firewall holes if you don't have air conditioning or if you have deleted your heater core. Fits 1" body panel holes for all years.Sold as a pair.Original Ford part 377678-S2

Reproduction, nice thick firewall insulation pad for the Mercury Cougar or Ford Mustang. We actually like this one better than the "premium" version. These are pre-formed for a perfect fit and appearance and greatly reduced engine noise and heat. The A/C and non A/C versions are the same piece and will fit both A/C and non A/C cars.This pad comes with all the rubber clips needed for installation.

"Premium" firewall pad for your 67 - 68 Cougar or Mustang. It's "premium" in the sense that it's more expensive. The main difference between this and the "economy" version is that it has a layer of foil inside, which helps with heat insulation. However, the total thickness is actually a little less than the economy version. This may make it easier to install, along with the included hard plastic clips (unlike the rubber originals). Given the significant difference in price for negligible...

Sold individually. Replaces Ford Part #: C7ZZ-3513.

Oil filter adapter for all Ford small block engines including 221, 260, 289, 289HiPo, 302, and 351W engines. Ford indicates that this was used 1962-1970. Screws into the engine block. We do not know the threads, but the small side is standard oil filter sized.Ford part number C2OZ-6882-C.

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...

Top screw on the wing or vent window frame on any 1967-68 Mercury Cougar or Ford Mustang. Screw attaches the door glass run insert to the chromed vent frame at the top. Screw accessible when door is open top leading edge of wing window frame. *Item of Note - screw is slightly too long. The tip could scratch the front edge of the door glass or chrome trim on top of the door window. We suggest grinding down the tip about 1/8 inch, prior to installation. We have looked and this is the only...

This flat nut has many uses, most commonly used on the 67 - 68 corral / walking cat headlight eyelid door assembly or the 69 - 70 quarter script. Can be used on anything that has a 3/32" stud. Can be used for many items on a variety of vehicles including the Mustang, Torino, Cyclone etc.Sold individually.

Quality built new automatic transmission flex plate for all 1967-68 Mercury Cougar and Ford Mustang with 289/302 engines and C-4 automatic transmissions. Looks identical to the OEM Ford plates, has new starter ring installed. Has the correct 28oz. weight for vintage 289/302 engines. The 5.0 liter engines used a 50oz. imbalance.

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

This piece runs under the floor over the transmission where the floor pan meets the firewall.

Reproduction driver side (left hand) floor pan to cowl side panel for Mercury Cougar and Ford Mustang. Normal 0 false false false EN-US X-NONE X-NONE Here's our little film to help you fortify your car! ...

Good quality reproduction shifter assembly for all 1967-68 Mercury Cougar and Ford Mustang with consoles. NOTE: This assembly does not come with the lower bushing.

Fits Standard and XR7

New fluorescent needle restoration paint for the gauges in your Mercury Cougar or Ford Mustang. Over the years, the sun has wreaked havoc on your Cat or Pony. This sun damage has also had it's way with the needles on you gauges and washed them out. This true fluorescent paint will not only make your needles look factory fresh, but will also bring back their glow at night. One jar contains 2.25ml worth of paint.

New manufactured flywheel for manual transmissions. Fits all 1967-68 Mercury Cougar and Ford Mustang with 289 engines with 3 or 4 speed manual transmissions. This flywheel has a 157 tooth ring gear. This flywheel will fit many other Ford small block V-8's with the 157 tooth gear.*Note - Most 1968 and newer Cougars came with 164 tooth flywheels, and they are not compatible.

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

C7ZB-17664-A Foot operated electric wiper actuating device for engaging the windshield washer pump or to cycle your windshield wipers once manually in light rain. Ford MPC number C7ZZ-17664-A. For any 1967 - 1968 Mercury Cougar and Ford Mustang.NOTE: If your electrical points are fried, you can simply replace them with the used contact replacement kit.Please note the Core deposit ...

Windshield Washer Pump Pedal Pad for 1967-1968 Mustang & Cougar. Keep your foot from sliding off the pedal with this Injection-molded rubber pad with vertical grooves just like original. This pad was used on models with a floor mounted washer pump pedal. (7664A) This is almost always missing off of the end of your foot operated washer pump. Replaces Ford part number C7ZZ-17664-A. We also have good used pumps in stock.Thanks for the plug Mark!: My first deal with Don was clear back in the 1980s...

Reproduction rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1968 Mercury Cougar and Ford Mustangs. New part with a fine threaded stud, also called a pinion bumper. The correct casting number is seen on this rubber axle bumper is C3AA-4906-C, this version has fine threads. The version most often seen on the 1969-70 is C9OA-4906-A. It will have a course threaded mounting stud.

This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...

NOS pamphlet from the Ford Motor Company detailing the 24 month 24,000 mile, or 5 year 50,000 mile warranties for the line of 1967 Cars and light trucks including Falcon, Mustang, Cougar, Ranchero, Fairlane, Thunderbird, Bronco, Light Trucks, Comet, Continental and Econoline.Volume 67C16L6

Very clean, original condition. Same as Cougar but you would have to bore holes in it for the top pad to use on the 1967 standard or 1967 - 1968 XR7 Cougar.

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan. Includes driver and passenger sides.

Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Reproduction passenger side (right hand) inner front frame patch for the Mercury Cougar or Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown. 

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Brass and steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 20 piece set with threaded screw in plugs as shown. 

Complete air vent assembly with cable, knob and bracket ready to bolt to your cowl. Replaces Ford Part # : C7ZZ-6501934-A

Our good used vents will not have cracks in the plastic or a rusty flapper from a leaking cowl. These are the same for AC and non AC.Replaces Ford part number C7ZZ-6501935-A.

Core bench seat for the 1967 Mercury Cougar or Ford Mustang equipped with decor interior. The foam almost will always be deteriorating or even missing. All seat cores will be solid frames taken from a Western parts car. Seat tracks are sold separate.

This system features the "Original" Baer 2-piston, pad guided caliper (PGC) mounted to a 11.29", 1-piece slot, drill, zinc plated integral hub rotor. The PGC caliper comes in a red powder coated finish with a black logo, includes dust/weather seal's and uses the popular D412 pad type. The system includes premium bearings with races pre-installed, dust caps, mounting brackets, stainless braided hoses and all necessary hardware. The 11.29" "Classic" system fits select 14" and most 15" or larger...

This system features the "Original" Baer 2-piston, pad guided caliper (PGC) mounted to a 13", 1-piece slot, drill, zinc plated integral hub rotor. The PGC caliper comes in a red powder coated finish with a black logo, includes dust/weather seal's and uses the popular D412 pad type. The system includes premium bearings with races pre-installed, dust caps, mounting brackets, stainless braided hoses and all necessary hardware. The 13" "Classic" system fits select 17" or larger wheels....