1967 Ford Mustang

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For use with 28 splined axles, but can be custom...

Limited slip, nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Used modern design Detroit Locker unit, new Richmond ring and pinion gear, new Timkin bearings, new selective size sleeve, new bolts, and new seal. Rebuilt using 1967-1973 nodular 9 inch cases with oil fill plug, for 28 or 31 splined axles. This unit was used in 1967-73 Cougars and Mustangs, but it also came in any other Fords or Mercurys with a 9 inch drop out center section....

Limited slip 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and new a seal. Rebuilt using the standard 9 inch case, with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it works for any other Mercurys or Fords with a 9 inch...

Limited slip 9 inch Ford third member rebuilt with all new or reconditioned parts. Rebuilt 4 pinion Trac-Loc unit, with new clutches, steels, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using standard 9 inch cases with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit was used in Cougars and Mustangs, but also any other Fords...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch case with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it can also be used for any other Ford or...

Limited slip 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967-1973 standard 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used on any other Ford or Mercury with a 9 inch drop out center section. Because of all the various ring and pinion...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a 1967-1973 nodular 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used in any other Ford or Mercury with a 9 inch drop out center section. Because of all the...

Also called a pumpkin, 2.79:1 open ratio. Check your door tag under "Axle". 1967 code 0 (zero) 1968 code 2

Also called a pumpkin, 3.00:1 open ratio. Check your door tag under "Axle". 1967 code 1 1968 code 5

Also called a pumpkin, 3.00:1 open ratio. 1967 9 inch third members did not originally come with fill plugs. The back of the housing had the oil fill plug. You can mix and match 9 inch assemblies from 1967-1970, just make sure that you have at least one fill plug. Check your door tag under "Axle". 1967 code 1

Since we always claim to have parts nobody else does... This welds to the bottom side of the car just above the differential. When the rear suspension bottoms out, this is the plate the rubber snubber / bumper (mounted on the front on top of the dif.) makes contact with.

Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S

Used diffuser for the shift indicator lamp. This diffuser is used on the Cougar or Mustang WITH a console and attaches to the end of the light socket on your shift indicator wire harness. Both shift indicator lamps with or without a console used the same wire harness and socket, but used different diffusers. The difference in the harness from the 67 to the 68 was different colored wires and different plugs. Replacement bulbs can be found on our site as well. ...

Used diffuser for the shift indicator lamp. This diffuser is used on the Cougar or Mustang WITHOUT a console and attaches to the end of the light socket on your shift indicator wire harness. Both shift indicator lamps with or without a console used the same wire harness and socket, but used different diffusers. The only difference in the harness from the 67 to the 68 was different colored wires.

Original dipstick or in Ford speak "Indicator - Oil Level" for C4 automatic transmissions. Application for 1967-68 Mercury Cougar 1966-70 Ford Mustang with 289/302 engines and C4 automatic transmissions, code "W" on your door data plate.Ford part # C6OZ-7A020-B.

Reproduction transmission dipstick tube for 67 - 70 Cougars or Mustangs equipped with the C4 automatic transmission.Replaces Ford Part number C6AZ-7A020-B

Fits C4 transmissions. Painted glossy black. O-ring included Replaces Ford part # C6OZ-7A228-B. Application 1967 - 1968 Mercury Cougars with 289/302 engines and automatic (C4) transmissions, code "W" on your door data plate. 1966 - 1968 Ford Mustangs with 28/302 engines and automatic transmissions, code "W" on your door data plate.

Fits C4 transmissions. Chrome finish. O-ring included Replaces Ford part # C6OZ-7A228-B. Application 1967 - 1968 Mercury Cougars with 289/302 engines and automatic (C4) transmissions, code "W" on your door data plate. 1966 - 1968 Ford Mustangs with 28/302 engines and automatic transmissions, code "W" on your door data plate.

Reproduction disc brake master cylinder cap for the Mercury Cougar or Ford Mustang. This unit has the correct stampings, rubber inner gasket, and is considered show quality. This cap will only fit master cylinder part # 15298.Replaces Ford part # C7AZ-2162.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang / Torino1968 Ford Mustang / Torino 1969 Ford Mustang / Torino 1970 Ford...

Reproduction adjustable disc brake push rod set for the Mercury Cougar or Ford Mustang. When you convert to manual disc brakes, this kit eliminates excess pedal travel and insures quicker braking response. NOT for power disc brakes. For Manual disc brake cars ONLY.

Excellent USA made quality replacement disc brake rotor. One piece rotor with wheel studs as shown, also includes installed bearing race. Replaces Ford Part #: C5ZZ-1102-B.

New high quality factory replacement rotors for early Mustang and 1967 Cougar 4 piston cars. Also a replacement for many aftermarket Ford disc brake conversions. These drilled and slotted brake rotors come ready to install on your vehicle with bearing races installed from the factory. Sold as a pair only as they are directional / side specific. For use with stock calipers. Precision drill pattern vents away heated gasses caused by braking, allowing for more contact between pad and rotor....

Reproduction disc brake distribution block for Mercury Cougar or Ford Mustang with factory installed disc brakes. Mounts to the driver side fender apron with a single bolt. Bare block without single pin brake switch.  Replaces Ford part # C7ZZ-2B257-D. Check out this video

Used disc brake distribution block for Mercury Cougar or Ford Mustang with factory installed disc brakes. Mounts to the driver side fender apron with a single bolt. Bare block without single pin brake switch. See also our rebuild kit that includes all the seals for the distribution block and proportioning valve. Plan on testing and or rebuilding before installation. Rebuild kits available. Ford part # C7ZZ-2B257-D. Check out this video ...

Used Distributor / 289-2V / Automatic Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7OF-12127-B  

Used Distributor / 289-2V / for the 1967 Mercury Cougar / 1967 Ford MustangFord part number  C7OF-12127-J  

Used Distributor / 289-2V / Manual Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7OF-12127-A  

Used Distributor / 289-2V / Manual Transmission for the 1967 - 1968 Mercury Cougar / 1967 - 1968 Ford MustangCurrent distributor is dated 7B23, Feb 23, 1967. Ford part number C7OF-12127-D  

Used Autolite distributor with the Ford part number of C7ZF-12127-F. This distributor was specifically used on 289-4V engines with manual transmissions. These used distributors should be considered rebuildable cores. Most will be complete, less the vacuum advance units. This is a tough one to keep in stock, the current one in stock as of March 2019 is dated 8D9 or April 8, 1968. Apparently, this distributor was used for Canadian cars with open emissions in 1968. So add 289-2V, 302-2V, and...

Used Distributor / 289-4V / Manual Transmission for the 1967 Mercury Cougar / 1967 Ford Mustang Ford part number C7ZF-12127-E Current distributor is dated 6L18, November 18, 1966.  

Used Distributor / 289-4V / Manual Transmission for the 1967 Mercury Cougar / 1967 Ford Mustang Ford part number C7ZF-12127-E Current distributor is dated 6M15, December 15, 1966.  

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has two pressed in brass fittings for vacuum hoses. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1970 vacuum advance, the earlier vacuum advances had one of the vacuum fittings that screwed...

Ignitor 1 by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. There is also an upgraded Ignitor II available. -50F To 300F Working Temperature Range, 0-15,000 Rpm Range, This Easy To Install And Maintenance Free Electronic Ignition System Features Solid-State Electronics And Rotating Cobalt...

Ignitor II by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. Adaptive Dwell Control -  Dwell increases with RPM to provide an average of 4 times the available energy between 3000 and 5000 RPM and twice the available voltage at the plug. -50F To 300F Working Temperature Range,...

New Old Stock vacuum advance. This style used 1972 on Motorcraft 351-4V V-8 distributors. DD-339 and code 348 numbers associated with this unit. This is an MOTORCRAFT marked vacuum advance. Brass nipple not included, but is needed. Instructions for installation with this one too. Application is for Q code 351CJ distributors marked D2ZF-12127-GA, D2ZF-12127-GB, D2ZF-12127-GC, D2ZF-12127-HA, and D2ZF-12127-HB. Ford Part Number D2ZZ-12370-A ...

New Old Stock vacuum advance. This style used 1968-69 on Autolite V-8 distributors. A12 and DD-236 numbers associated with this unit. This is an Autolite marked vacuum advance Threaded cap and spring not included Ford Part Number C8AZ-12370-A

New Old Stock vacuum advance. This style used 1965-67 on Autolite V-8 distributors. Designed for use with a threaded nipple. DD-190 and code 303 numbers associated with this unit. This is an MOTORCRAFT marked vacuum advance, there are other service replacement units marked Autolite. Threaded nipple available separately. Ford Part Number C5AZ-12370-A

Reproduction single port vacuum advance for most all 1967-71 Ford V-8 engines. Fits Ford's brand of Autolite and Motorcraft distributors found on all 1967-71 Mercury Cougar and V-8 Ford Mustangs.

New Old Stock upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428.  * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...

Reproduction upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428.  * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Replaces Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #107 or DF-342, single points cam with weights marked 13L and 18L from the top. Factory used on small block and FE distributors.  Ford part number C5AZ-12210-A.

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #108 or DF-343, single points cam with weights marked 10L and 15L from the top. Factory used on small block and FE distributors.   Ford part number C5AZ-12210-B.

New Old Stock Autolite distributor cap for the 1964, 1965 1966 Ford and Mustang. Technically a service replacement cap, this cap has aluminum contacts, not brass. Fits all Ford V8 engines 1957-73. Before and beyond. Does not have "AUTOLITE" on the cap, just a "1", typical cap used 1957-1966 of Ford V-8's. Ford part number B7A-12106-A. 

Exact copy reproduction concourse correct distributor cap with raised Autolite logo. Good for all 67 - 73 Cougars and Mustangs. A must have for anyone building a show car.

New Old Stock MOTORCRAFT distributor cap for the 1967 - 1973 Mercury Cougar or Ford Mustang. Technically a service replacement cap, this cap has an embossed "MOTORCRAFT" on top. Fits all Ford V8 engines 1967-73. Before and beyond.Ford part number B7A-12106-A. 

Reproduction distributor cap for the 1967 - 1973 Mercury Cougar or Ford Mustang 

Reproduction Distributor Condensor for the 1967 - 1973 Mercury Cougar and Ford Mustang

NOS distributor lead wire without the boot for the coil. There were at least two different lengths of wire leads found on 1967 Mercury Cougar and most all other Ford and Mercury distributors. This is the longer wiring harness, about 20 inches outside of the distributor. Direct replacement for 1961-67 Ford distributors.Ford part number C1VF-12216-A.