Home > 1969 Mercury Cougar
All Available Parts - 1969 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 201-300 of 5304
Sorted By:
Availability:
Display Options:
Availability: Used / Wrecking Yard Item
Item #: 12297 -
Good used passenger side (right hand) moulding / trim for the Mercury Cougar that was NOT equipped with a vinyl top. These units will not have dents or deep scrapes and will be ready to install on your driver / occasional show car. Expect one or two very small dings and some scratching on the underside where glue in glass has come undone at some point. The vinyl top cars have a wider top edge but a narrow bottom edge where the non vinyl cars have a narrow top edge with a wide bottom edge....
Featured!
Availability: In-Stock Item
Item #: 13011 -
Upper and lower fuel filler door trim pieces for 1969 and 1970 Mercury Cougars, all models except 1970 Eliminator which were black. To receive core credit back your cores must have only light pitting and no broken studs. Original Ford part number C9WY-65405-A for the lower and C9WY-65405A48-B for the upper.
Featured!
Availability: In-Stock Item
Item #: 31186 -
These are BLEMISHED right and left hand set of 1/4 panel window mouldings. As you can see from the first two pictures above, these blems will have some minor bubbling or small dings in the chrome. These will be great for a daily driver if you're not worried about a few small imperfections. Some refer to these as "Hockey Sticks" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled...
Availability: In-Stock Item
Item #: 31319 -
This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.You can find our reproduction pair of brackets here. ...
Availability: Used / Wrecking Yard Item
Item #: 31320 -
This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb. You can find our reproduction pair of brackets here. ...
Availability: In-Stock Item
Item #: 31321 -
These aluminum ninety degree brackets are what fastens the XR7 chrome boot moulding to the quarter panels. The beltline weatherstip also attaches to them. These parts are only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass
Availability: Out of Stock
Item #: 32917 -
Reproduction passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...
Availability: Out of Stock
Item #: 32918 -
Reproduction driver side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 33054 -
Economy reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible, except for the fact that the clips included have 8mm nuts, unlike the originals. There is however one small problem, the metal on these mouldings is much softer than the originals and you have to take extra care when installing the clips, if you apply too much pressure when installing, you will dimple the...
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 33410 -
Premium reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible. This version is also much more rigid when compared to the economy version and is not so prone to denting by applying too much pressure when installing. Clips sold separately. This premium moulding weighs 10 oz., compared to the economy deck lid moulding at 6 oz., and an original moulding at 7...
Availability: In-Stock Item
Item #: 41349 -
1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16
Availability: In-Stock Item
Item #: 20428 -
These trim parts (as with all our restored aluminum) feature the correct bright dip anodized plating, just as they came from the factory. If you have extra cores you would like to sell then we would like to hear from you! Please DO NOT send heavily damaged trim parts as the finished product will be delicately thin. Cores that are corroded, torn, smashed or kinked are not acceptable cores either. Please, only send cores with small dings, scratches and dullness. Extra screw holes and...
Availability: In-Stock Item
Item #: 24755 -
Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...
Availability: In-Stock Item
Item #: 18692 -
If you happen to have a set of three NOS wheel lip mouldings and purchase the fourth as a restored piece from us it will visually fit right in. Restored is never as good as NOS as the polishing process will make the part thinner which means it will be more prone to damage than an un-restored original or NOS trim part. Note! Road trash of all sorts, sand, gravel, etc. ends up in the gutter to the right hand side of the road. The front tire tends to form a vacuum and sucks stuff away from the...
Availability: In-Stock Item
Item #: 18688 -
Keep in mind you can get FREE trim parts from us if you have a quantity of good quality cores to exchange!Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...
Availability: In-Stock Item
Item #: 18690 -
These look great and because they have the correct anodized finish they will not get dull like a part that has only been polished will.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you still have questions about your cores, check out the video below. ...
Availability: Rare / NOS Part
Item #: 18707 -
New Old Stock driver side rear wheel lip moulding for any 1969-70 Mercury Cougar.Replaces Ford part number C9WY-6529165-A, or D0WY-6529165-A.
Availability: Used / Wrecking Yard Item
Item #: 18708 -
Good used wheel lip moulding with no corrosion, obvious scratches or dents. Will have some what rough texture down low on the leading edge from road debris. This moulding will still have a good shine but do not expect NOS quality from a used piece of aluminum such as this one. When sending us a core in exchange please do not send twisted, ripped, corroded parts for an exchange. Dull, slightly dented, warped or scratched (not gouged) trim parts are OK as cores. If you are in question as to...
Availability: Used / Wrecking Yard Item
Item #: 18691 -
Good used wheel lip moulding with no corrosion, obvious scratches or dents. This moulding will still have a good shine but do not expect NOS quality from a used piece of aluminum such as this one. When sending us a core in exchange please do not send twisted, ripped, corroded parts for an exchange. Dull, slightly dented, warped or scratched (not gouged) trim parts are OK as cores. If you are in question as to whether your core is worthy of restoration or not please send us a digital picture...
Availability: Used / Wrecking Yard Item
Item #: 18693 -
Good used wheel lip moulding with no corrosion, obvious scratches or dents. Will have some what rough texture down low on the leading edge from road debris. This moulding will still have a good shine but do not expect NOS quality from a used piece of aluminum such as this one. When sending us a core in exchange please do not send twisted, ripped, corroded parts for an exchange. Dull, slightly dented, warped or scratched (not gouged) trim parts are OK as cores. If you are in question as to...
Availability: Used / Wrecking Yard Item
Item #: 18689 -
Good used wheel lip moulding with no corrosion, obvious scratches or dents. This moulding will still have a good shine but do not expect NOS quality from a used piece of aluminum such as this one. When sending us a core in exchange please do not send twisted, ripped, corroded parts for an exchange. Dull, slightly dented, warped or scratched (not gouged) trim parts are OK as cores. If you are in question as to whether your core is worthy of restoration or not please send us a digital picture...
Availability: Used / Wrecking Yard Item
Item #: 20422 -
Good set of four used wheel lip mouldings for your 1969 - 1970 Mercury Cougar. What is considered to be an "acceptable core" is solely at our discretion. If you are in question as to what good cores are, please send quality, in focus, close-up digital pictures to westcoast@classic-cougar.com *NOTE* Some "on the edge" cores that need extra labor can be given a partial credit.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by WCCC....
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 33053 -
Set of 4 reproduction wheel lip mouldings for the 69-70 Cougar. These are spot on and we had no problem fitting them on our cars, the only difference we noticed is that the aluminum is softer than the originals and prone to dimpling. And since they're reproductions, no cores are required! Keep in mind that when you remove your rear core mouldings, you can send them to us as they might be eligible for in store credit. For more info on aluminum trim restoration & core exchanging, check out our...
Availability: In-Stock Item
Item #: 20409 -
If you shop around you will see many places charge less than this... We have tried several different places that restore stainless trim and they all came back less than mint. These are arrow straight and have been polished to a very high luster. This trim parts will accentuate your new paint job in an incredible way!"...Don - Happy Fourth of July. I wanted to send a note to your team of gratitude for all the help they provided me over the last three years restoring my Cougar. As you know, it...
Availability: In-Stock Item
Item #: 20418 -
Restored upper left window moulding / trim for the Mercury Cougar.
Availability: In-Stock Item
Item #: 20419 -
Restored upper right rear window moulding / trim for the Mercury Cougar.
Availability: In-Stock Item
Item #: 20398 -
Restored lower left rear window moulding / trim for the Mercury Cougar.
Availability: In-Stock Item
Item #: 20399 -
Restored lower right rear window moulding / trim for the Mercury Cougar.
Availability: Used / Wrecking Yard Item
Item #: 12661 -
Good used four piece set with no dings or heavy scratches. Ready to install on your Cougar as is or polish them to a mirror like finish to be installed on a show car.
Availability: Used / Wrecking Yard Item
Item #: 20387 -
Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.
Availability: Used / Wrecking Yard Item
Item #: 20406 -
Used passenger side (right hand) upper rear window moulding / trim for the Mercury Cougar.
Availability: Used / Wrecking Yard Item
Item #: 20383 -
Used driver side (left hand) lower rear window moulding / trim for the Mercury Cougar.
Availability: Used / Wrecking Yard Item
Item #: 20402 -
Used passenger side (right hand) lower rear window moulding / trim for the Mercury Cougar.
Availability: Used / Wrecking Yard Item
Item #: 12684 -
Core stainless steel mouldings will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.
Availability: Used / Wrecking Yard Item
Item #: 12720 -
Core stainless steel mouldings will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.
Availability: Used / Wrecking Yard Item
Item #: 12710 -
Core stainless steel mouldings will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.
Availability: Used / Wrecking Yard Item
Item #: 20405 -
Availability: Used / Wrecking Yard Item
Item #: 20400 -
Availability: In-Stock Item
Item #: 33526 -
Reproduction set of 4 rear window mouldings / trim for the 69 - 70 Mercury Cougar. No core required, but keep in mind that we will give store credit for your original restorable trim!
Availability: Used / Wrecking Yard Item
Item #: 12713 -
Core grade windshield moulding for the passenger side windshield vertical stainless steel. 1969-70 Mercury Cougar and Ford Mustang coupes.Ford part number D0ZZ-6503148-B.
Availability: Used / Wrecking Yard Item
Item #: 12702 -
This driver side lower windshield moudling core is a great candidate for restoration for you do-it-yourselfers out there looking to save a buck. Or if you're driving around in a lower quality daily driver and you're missing this piece, we got what you need. Ford part number D0ZZ-6503149-B.
Availability: Used / Wrecking Yard Item
Item #: 12721 -
Used grade upper windshield moulding for any 1969-70 Mercury Cougar or Ford Mustang hardtop. Ford part number C9ZZ-6503144-A.
Availability: Used / Wrecking Yard Item
Item #: 12716 -
Because these passenger side vertical windshield mouldings are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used "core quality" pieces. They are a great option if you have damaged or missing trim but plan to professionally restore your trim. Restorable, but not as nice as our "used" pieces. These are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have...
Availability: Used / Wrecking Yard Item
Item #: 12705 -
Core driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang. This core grade unit is suitable for restoration or, if you are missing this piece, will fit right in with the rest of your driver quality trim.Ford part number C9ZZ-6503137-A.
Availability: Used / Wrecking Yard Item
Item #: 20431 -
Because this windshield moulding set is comprised of used original pieces, it will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part numbers include: C9ZZ-6503136-A, C9ZZ-6503137-A, C9ZZ-6503144-A,...
Availability: Used / Wrecking Yard Item
Item #: 20389 -
Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503137-A. *NOTE* If you have questions about your cores, check out our video below. ...
Availability: Used / Wrecking Yard Item
Item #: 20421 -
Because these upper windshield mouldings are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503144-A. *NOTE* If you have questions about your cores, check...
Availability: Used / Wrecking Yard Item
Item #: 20408 -
Because these passenger side vertical windshield mouldings are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have questions about your...
Availability: Used / Wrecking Yard Item
Item #: 20404 -
Because these are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503148-B. *NOTE* If you have questions about your cores, checkout our video below. ...
Availability: Used / Wrecking Yard Item
Item #: 20385 -
Because these lower windshield mouldings are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503149-B. *NOTE* If you have...
Availability: In-Stock Item
Item #: 20429 -
This original FoMoCo, five piece windshield trim set has been lovingly restored to far beyond the original luster. Stunning brilliance, perfect match for that high end paint job. Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well.Ford part numbers include: C9ZZ-6503136-A, C9ZZ-6503137-A, C9ZZ-6503144-A, C9ZZ-6503148-B, and C9ZZ-6503149-B....
Availability: In-Stock Item
Item #: 20384 -
Because these lower windshield mouldings are lovingly restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. They are an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503149-B. *NOTE* If you still have questions about your cores, check out our video below. ...
Availability: In-Stock Item
Item #: 20403 -
Because these side lower windshield mouldings are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. This package is also an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503148-B. *NOTE* If you have questions about your cores, check out our video below. ...
Availability: In-Stock Item
Item #: 20388 -
Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503137-A. *NOTE* If you have questions about your cores, checkout our video below. ...
Availability: In-Stock Item
Item #: 20407 -
Restored passenger side (right hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. Because this windshield moulding / trim is a restored original piece, it will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. They are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have questions about your cores, check out our video below. ...
Availability: In-Stock Item
Item #: 20420 -
Because these upper windshield mouldings are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. This package is also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503144-A. *NOTE* If you have questions about your cores, check out our video below. ...
Availability: Used / Wrecking Yard Item
Item #: 15-0205 -
This is a tension spring that defaults the steering wheel to up and or tilt away position. The spring in the 68 - 69 Column is stronger and taller than the 1967 column spring.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: In-Stock Item
Item #: 15-0170 -
Reproduction rubber roller for the metal tilt cover plate on any 1968-69 Ford, Mercury, or Lincoln. Often times the rubber disintegrates over time. This is needed to keep the cover plate tight to the side of the steering column. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: In-Stock Item
Item #: 30564 -
New manufactured Tilt / Tilt-Away cable for any 1968-69 Mercury Cougar or Ford Mustang with factory tilt steering column. All new parts developed by our in house steering column expert DW. Not created from used parts. The cable sheathing will not split or crack over time like the originals.Replaces Ford part number C9ZZ-3E520-A*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...
Availability: In-Stock Item
Item #: 31875 -
Reproduction steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 - 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: Out of Stock
Item #: 42374 -
Replaces Ford part number C9WY-16038-B.
Availability: Rare / NOS Part
Item #: 42375 -
Replaces Ford part number C9WY-16039-B.
Availability: Rare / NOS Part
Item #: 42382 -
Why is this right rear wheel lip so costly and difficult to find these days? Consider this... The right rear was the first to go obsolete from Ford. The right rear is the one most likely to get damaged because of it being the corner that is in the "blind spot". Remember, these early Cougars did not have RH mirrors! Lastly and maybe the most relevant is the fact that the right rear wheel is your traction tire which means more damage from flying road debris, loose tire chains and the like. It...
Availability: Used / Wrecking Yard Item
Item #: 27139 -
This original FoMoCo, six piece windshield trim set for the Mercury Cougar convertible. Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. The four upper pieces are wider than the coupe versions, but the lowers are the same (with about an inch cut off the ends). The trim is... trimmed so it will fit underneath the pillar trim pieces. *NOTE* If your trim has...
Availability: Rare / NOS Part
Item #: 27147 -
This set of NOS mouldings has been one by one taken out of the wrapper, cleaned and carefully inspected one by one for imperfections or blemishes. Even factory blemishes are not included in this show quality, pristine set. At this price you need to know you are getting the best of the best. We will allow credit for your used or core wheel lip mouldings. You can send your used or core wheel lips in prior or after your purchase and we will call and discuss what amount of credit we will allow on...
Availability: In-Stock Item
Item #: 26095 -
The four part, die cast vinyl top trim kit requires 15 (right rear under back glass is the odd ball that requires five fasteners) of these speed nut fasteners. These speed nuts also can be used on the 1969-70 Mercury Cougar XR7 dash courtesy light bezels, two for attaching that bezel to the dash pad.*NOTE* These speed nuts only work with factory installed die cast vinyl top mouldings.*NOTE* The factory nuts had a drop of silicone or trim adhesive inside the bowl that acted as a seal. This...
Availability: In-Stock Item
Item #: 30942 -
Set of four re-chromed vinyl top mouldings. The vast majority of hardtops in 1969 and 1970 had painted mouldings, but on two tone painted cars and the 1970 "Hounds-tooth" edition, chromed mouldings were supposed to be included. However, we have found exceptions to the rule. If you have extra sets of cores above and beyond the four needed to exchange, we would be willing to give in store credit. Restored moulding will not ship until we receive your cores. All mounting studs must be intact to be...
Availability: In-Stock Item
Item #: 33135 -
Set of four NOS vinyl top mouldings. The vast majority of hardtops in 1969 and 1970 had painted mouldings, but on two tone painted cars and the 1970 "Hounds-tooth" edition, chromed mouldings were supposed to be included. However, we have found exceptions to the rule.NOTE: These mouldings will have some shelf wear, see photos above. If you have extra sets of cores, we would be willing to give in store credit. Ford casting numbers on backs: Driver side C9WB-65423A19 Passenger side...
Availability: In-Stock Item
Item #: 41343 -
#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.
Availability: In-Stock Item
Item #: 13065 -
This gas Shock Absorber improves handling without sacrificing ride comfort. A very good choice for the daily driver wanting a smooth ride with the response of a gas shock. These shocks are sold individually and are designed more specifically to work with Cougars as opposed to Mustang. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop19.3711.308.07X-- ...
Availability: In-Stock Item
Item #: 26714 -
These shocks are the as close to original specs as possible for the Mercury Cougar. This is the performance shock for those looking for firmer ride. The KYB Gas-a-Just shocks use higher gas pressure to keep your tires glued to the road. The KYB Gas-a-Just shocks' velocity-sensitive valving system adjusts quickly to changing road conditions for maximum comfort in any situation. Their mono tube configuration eliminates aeration and foaming, their micro-smooth, hard-chromed pistons extend their...
Availability: In-Stock Item
Item #: 26558 -
Sold individually, two required per car. Replaces Ford part # C3DZ-4730.
Availability: Used / Wrecking Yard Item
Item #: 24633 -
Passenger side shock mounting plate for any 1967-73 Mercury Cougar with any V-8 engines. A passenger side and **driver side bracket are needed for most applications. **Excludes 1969 - 1970 Boss 302 & 428 Cobra Jet 4 speed Cougars. Additionally 1972 - 1973 351CJ (Q code engines - all transmissions) which all came with staggered rear shocks, which was part of those years Competition Handling Package. These applications had staggered rear shock plates. Order two C9OZ-5796-C right...
Availability: Ships Direct from Supplier (Except International)
Item #: 20509 -
Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new 4 pinion Trac-Loc unit, new Motive ring and pinion gears, new Timkin bearings, new crush sleeve, new bolts, and new seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. There are various ring and pinion (gear) ratios and axle splines available, if you are unsure of what you need it is best to call (503) 463-1130 for your order. This is a drop ship item. *Note - New...
Availability: Ships Direct from Supplier (Except International)
Item #: 20510 -
Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For use with 28 splined axles, but can be custom...
Availability: Ships Direct from Supplier (Except International)
Item #: 19802 -
Limited slip 9 inch Ford third member rebuilt with all new or reconditioned parts. Rebuilt 4 pinion Trac-Loc unit, with new clutches, steels, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using standard 9 inch cases with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit was used in Cougars and Mustangs, but also any other Fords...
Availability: Ships Direct from Supplier (Except International)
Item #: 19801 -
Limited slip 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and new a seal. Rebuilt using the standard 9 inch case, with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it works for any other Mercurys or Fords with a 9 inch...
Availability: Ships Direct from Supplier (Except International)
Item #: 19803 -
Limited slip 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967-1973 standard 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used on any other Ford or Mercury with a 9 inch drop out center section. Because of all the various ring and pinion...
Availability: Ships Direct from Supplier (Except International)
Item #: 19798 -
Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch case with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it can also be used for any other Ford or...
Availability: Ships Direct from Supplier (Except International)
Item #: 19800 -
Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a 1967-1973 nodular 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used in any other Ford or Mercury with a 9 inch drop out center section. Because of all the...
Availability: Ships Direct from Supplier (Except International)
Item #: 19797 -
Limited slip, nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Used modern design Detroit Locker unit, new Richmond ring and pinion gear, new Timkin bearings, new selective size sleeve, new bolts, and new seal. Rebuilt using 1967-1973 nodular 9 inch cases with oil fill plug, for 28 or 31 splined axles. This unit was used in 1967-73 Cougars and Mustangs, but it also came in any other Fords or Mercurys with a 9 inch drop out center section....
Availability: Used / Wrecking Yard Item
Item #: 24746 -
Most 1969 and 1970 351 engines 3 or 4 speed manual transmission. Shaft diameter 2-3/4 inches. Length 53-1/4 inches, measured on U-joint centers. Used and 'as balanced' from the factory. *NOTE* 1970 M-code - 351C-4V engines came from the factory with 3 inch drive shafts. Ask about slip yokes. Shipping is oversized due to length.
Availability: Used / Wrecking Yard Item
Item #: 24745 -
Most 1969 and 1970 351 engines with FMX transmissions. Shaft diameter 3 inches. Length 53-9/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory.*NOTE* Some 1970 M code 351C-4V engines came from the factory with 3-1/2 inch drive shafts. We think it may have been those with competition handling packages. Does anyone know for sure?Ask about slip yokes. Shipping is oversized due to length.
Availability: Used / Wrecking Yard Item
Item #: 16-0049 -
31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX cars. *Excludes 351C-4v and 351CJ engines.
Availability: In-Stock Item
Item #: 41624 -
Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually
Availability: In-Stock Item
Item #: 10577 -
[No Description Provided]
Availability: In-Stock Item
Item #: 10864 -
Reproduction rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1969 - 1970 Mercury Cougar and Ford Mustangs. New part with a course threaded stud, also called a pinion bumper. The correct casting number is seen on this rubber axle bumper is C9OA-4906-A, this version has course threads. The version most often seen on the 1967-68 is C3AA-4906-C. It will have a fine threaded mounting stud.
Availability: Ships Direct from Supplier (Except International)
Item #: 43175 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43213 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43217 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43221 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43225 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43229 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43233 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43237 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43241 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43262 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43266 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43270 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43275 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...