All Available Parts - 1970 Mercury Cougar

Kit includes all repair parts necessary to refurbish leaking cylinder/piston rod seal area. Replaces Ford Part #: C1AZ-3A764-A.

This new reproduction power steering ram cylinder is good quality with almost no warranty claims. However, When you go to put your cotter pin in the castle nut you will often find it does not align perfectly which means you may have to drill it for a perfect fit. Keep in mind we will pay $30 in in-store credit for a clean original used ram cylinder so don't throw them away! RAM BOOT SOLD SEPARATELY. Replaces Ford Part #: C3DZ-3A540-A or C7ZZ-3A540-A. ...

This an original, rebuilt power steering slave / ram cylinder. It has not had a cosmetic restoration so it will show external dings, scrapes and general wear associated with a 50 year old part located on the bottom of a car. If you buy our reproduction ram do not throw away your core used ram as we often can give in store credit for the part. RAM DUST BOOT SOLD SEPARATELY.Replaces Ford Part #: C7ZZ-3A540-A.

Reproduction rubber boot for the drag link end of the power steering ram cylinder on most any 1967-70 Ford small and intermediate sized cars. Comes with band style crimp clamp like the originals. Keep in mind that this product is made from material that is thinner and softer than OEM.

Power Steering hose bracket insulator for both the small and big block brackets for the 1967 - 1970 Mercury Cougar and Ford Mustang. Replaces Ford part #: C7ZZ-3A609-A or C7ZZ-3609. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are things coming to? Where is...

Unfortunately we have had a high rate of returns due to failure on these and can no longer enthusiastically recommend them. Please consider our original rebuilt units. This is the large nut control valve that Ford switched to after 1967. Many 1967 Cougars have been converted to the 1968 valve over the years so you may want to double check your valve before ordering. These units are designed to use type F fluid, not off the shelf power steering fluid. Please follow the procedures for...

Bolt kit for mounting power steering ram cylinder brackets to the frame rail on any 1967-70 Mercury Cougar or Ford Mustang. Kit includes: two short bolts with lock washers, long horizontal bolt, nut, and reinforcing washer. Quality AMK fastener kit.

This rod is correct for the 351 Cleveland 2V only and is approximately 27". A red paint daub was found on this rod, by trying to expose it with steel wool, it was almost erased. This would explain why we rarely find rods with the original paint daub in place. Slightly shorter than the 4V rod and has a lower connection point to the carburetor.

Transmission Vacuum line OE for the C6 transmission with 90 deg. bend at trans.

Manual control shift linkage assembly for a floor shift FMX transmission in any 1970 Mercury Cougar or Ford Mustang. Comes as shown.  1970 linkage includes a provision for the steering column lock out rod, compared to the 1969 version. Check out our video on rebuilding your shifter below: ...

First generation Cougars 1967 and 1968, used a single bracket for C4 automatics and both 3 speed and 4 speed manual transmissions. This bracket also carried over to 1969 and 1970 with 351 or Boss 302 engines and either 3 or 4 speed manual transmissions. Ford part number C7ZZ-6A023-D. This part weighs 2.28 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 1/4" on center and the passenger side 2 3/4" on center.The reproduction Dynacorn part...

For all 1969 and 1970 Cougars with H code 351-2V and M code 351-4V engines and FMX automatic transmissions. This part weighs 2.66 pounds and when set on a level surface the height of the mounting hole on the driver side measures 3" on center and the passenger side 3 1/8" on center. Ford part number C9ZZ-6A023-A. *NOTE* The picture with all four crossmembers in a line shows the three versions of the small block C-6 and FMX units in the foreground and the last is the big block C-6 unit. Notice...

New crossmember to adapt the Tremec TKO manual transmission to the Mercury Cougar or Ford Mustang. This unit can also be used for the Ford AOD. 

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Used dust and safety cover for all 69 - 73 Cougars and Mustangs with the FMX (code X) automatic transmission. Access plate for the torque converter and flex-plate.

Steel inspection cover for all 1967 Cougar or Mustang with any of the FE engines 390, 427, or 428CJ and C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter. Usually will have a casting number of C6AP-7986-A stamped on it, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.*Note - Some of these plates do not have the vent, or dimple at the bottom, like in the picture.Please keep in mind that this is a 40+ year old used item....

Reproduction steel inspection cover for all 67 - 70 Cougars or Mustangs with 390, 427, or 428CJ engines with the C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.

Reproduction dust and safety cover for 69 - 73 Cougars and Mustangs with the FMX (X code) automatic transmission. Access plate for the torque converter and flex-plate.NOTE - Although the FMX and the C4 inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.

4 Bolts for securing the inspection cover for any C-6 automatic transmission 1967-70 Mercury Cougar or Ford Mustang.

If your automatic floor shifter has play in it left to right then this is the culprit. Easy to install, (more difficult if you have a 67-68 with center console) these are made from a wear resistant plastic that is better than original. Sold as a pair as two are required per car. This bushing was used in all Ford products equipped with a floor shift automatic from the 1965 Mustang to the late 70's Pinto. Replaces Ford Part # C5ZZ-7A133-A Check out our video on rebuilding your shifter below: ...

It is as nice as it looks! Good fit. Replaces Ford Part #: C9ZZ-7E271-A Customer reviews: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it wasn't on there computer. At WCCC they said they were not sure but looked it up in a manual. That's customer...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-M and C5ZZ-7C488-D. Your buttons may have faded to gray after many years. These black buttons are injection molded plastic and have steel wear plates just like the originals. Technically this is a copy of the...

Tired of picking your broken button off the floor? This inserts in the left hand side of your deluxe (colored keyed) shift handle. Quality part made in China, please consider our good used units at half the price! 67 is actually a little different in contour but this will fit fine. Replaces Ford #: C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

Used to block light from escaping around shifter stem seal. Fits 1969-73 Mercury Cougar and Ford Mustang as well as 1971+ Pinto, Bobcat, Maverick, and Comet with floor shift automatic transmissions. The 90 degree notched portion straddles the set screw on the cast light housing. Most shifters (almost all) we see do not have this part in place any longer. Ford part number C9ZZ-7E130-A.Note: This fits perfectly on the shifters we have tried, but several customers have commented that it was too...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The early versions used the C5ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Automatic shifter dial black background. This part screws to the shifter bucket, and sits under the pointer when everything is assembled in your shifter bucket assembly. Fits all 1969-73 Mercury Cougar and Ford Mustangs with automatic transmissions. Original Ford part number C9ZZ-7A213-A also can be D1ZZ-7A213-A. Check out our video on rebuilding your shifter below: ...

Ford calls this part a 'mask'. This clamps to the chromed lever and holds the socket and bulb that are attached to the neutral safety switch, which are the shifter indicator light for the floor shifter. This cast piece will not have stripped treads or be corroded. It also fits 1971 and newer Maverick and Comet with floor shifters only. Ford part number C9ZZ-7B052-A. Check out our video on rebuilding your shifter below: ...

Automatic shifter arm pawl - late version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1970-73 Mercury Cougar and Ford Mustang. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need. Ford part number D0ZZ-7C442-A. Check out our video on rebuilding your shifter below: ...

This group of parts mounts to the top of the AT shifter arm and rides against the thumb activated button on your T shift handle. Its function is to lift the cable that runs through the chrome shifter stem to lock and unlock the shifter out of Park. The Ford technical name for this part is 'Roller - Shift Lever Lock'. We carefully inspect each part to make sure it is in perfect used condition. Ford part number C5ZZ-7D328-A. Check out our video on rebuilding your shifter below: ...

This gives the thumb release button in your T shaped shift handle its tension. If it is rusted then your button will not return back to its outer position easily. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Technically this spring fits all Ford and Mercury floor shifters 1965-73. Ford part number C5ZZ-7C300-A. The MPC shows this spring to have a free length of 2-1/16 inches.

Automatic shifter cable with slot on the threaded end for all 1969-73 Mercury Cougar and Ford Mustangs. Will also work on 1967-68 but features a slot at bottom so as to remove or adjust easily. The 1967-68 version did not have this slot. Ford part number C9ZZ-7D246-A with the slotted threaded stud on the end. Also fits 1971+ Maverick & Comet with automatic floor shifters. Restoration Hint - We suggest purchasing this upgraded cable for use in 1967-68 shifter levers. Much easier to install, and...

This keeper affixes to the top of the plastic indicator arrow.  Screws included. Check out our video on rebuilding your shifter below: ...

This fragile little plastic arrow is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

Lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had faux leather wrapping. Additionally it does not fit with the 1973 chromed T-handle without trimming.  Ford part C8ZZ-7C488-B.  Check out our video on rebuilding your shifter below: ...

1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. These are used, and because of the low grade of chrome plating, these will show some form of light pitting.  handle, which is larger and has a faux leather covered handle in a variety of colors. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Black plastic dummy button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is the non-moving button on the right side of your shifter handle. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had faux leather wrapping. Ford part C8ZZ-7C488-A.

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The late versions used the C9ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Automatic shifter arm pawl - early version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1967-70 Mercury Cougar, 1965-70 Ford Mustang, and 1965-66 Ford and Mercury full size cars with floor shift automatic transmissions. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need, this early pawl has a Ford part number...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

This arm is attached to your automatic transmission floor shifter (see picture at left). Fits all 1969-70 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for FMX and C-6 transmissions. Ford part number C9ZZ-7302-A. This part may have the course threads or fine threads. Normally this item ships with the course threads. We also stock the 1971-73 version that has a captured stud for...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the early version with small width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-A. *Note - Chromed lever and internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the late version with wider width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-C. *Note - Chromed lever internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

Reproduction of the little plastic shift indicator arrow, that is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the "Select-Shift" automatic transmission. FMX transmissions only, code "X" on your door data plate tag. All 351 engines received the FMX automatic transmission. Rod with casting number D0ZA-7340-A. Shift rod approximately 18 inches long. Ford part number D0ZZ-7326-D. 1970 only. Check out our video on rebuilding your shifter below: ...

Reproduction automatic shifter lever in chrome for the Mercury Cougar or Ford Mustang. Comes with inside cable parts. See the related items for more of your shifter needs. Check out our video on rebuilding your shifter below: ...

Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1969 and most 1970 Mercury Cougar or Ford Mustang with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-A. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for some 1970 Mercury Cougar or Ford Mustang, and all 1971-73 Cougar and Mustangs, with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Exact reproduction for the 1969 - 1973. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one. Replaces Ford Part #: C8OZ-7213-A, C90Z-7213-B, D3OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Bare automatic shifter bucket or housing for use with the large pawl (0.160") shifter levers. Fits most 1970 Mercury Cougar and Ford Mustangs with or without console. Check the thickness of the pawl on your shifter lever. There are two different sizes and need to be matched for optimum fit. Early pawls were 0.100" thick, sometime in early 1970 through 1973 the pawls were made larger at 0.159". We recommend purchasing new bushings prior to installation. Replaces Ford part number C9ZZ-7A306-?...

This arm is attached to your automatic transmission floor shifter. Fits all 1969-73 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. This used part will come with a captured lower stud for attaching the shift rod as shown. Correct for FMX and C-6 transmissions. This version is found on 1972-73 cars, it has the captured lower stud for mounting the automatic shift rod to the transmission. Ford part number D1ZZ-7302-A. Check out our video on rebuilding...

Unlike previous reproductions this has the correct grommet that passes through the firewall.  Replaces Ford Part #: C9ZZ-17260-A.  This cable measures 58 1/2" at its very most outer ends.

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Speedometer cable that fits all 1969-73 Mercury Cougar and Ford Mustang with C-6 transmissions. This replacement cable is longer than the originals and does not have the firewall grommet. This cable measures 80" inches in length. Does not include speedometer gear, has correct style plastic clip that attaches to the back of the speedometer. Replaces Ford part # C9ZZ-17260-B, D0ZZ-17260-D, and D1ZZ-17260-G.

Used clip with bolt for attaching the speedometer cable to the transmission of the Mercury Cougar or Ford Mustang. This unit holds the gear end into both automatic and manual transmissions. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 351W and FMX transmission. These are sold in pairs

Reproduction transmission cooling lines made of stainless steel for the Mercury Cougar equipped with the FMX automatic transmission and 351W engine. These lines are sold in pairs.

Reproduction transmission cooling lines made of OE steel for the late production 1968-70 Mercury Cougar or Ford Mustang equipped with the C-6 automatic transmission. These lines are also available in stainless steel and are sold in pairs.

Reproduction transmission cooling line made of stainless steel for the Mercury Cougar produced from late 1968 through 1970 that came equipped with the C-6 automatic transmission. These lines are also available in OE steel and are sold in pairs.

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the FMX automatic transmission and 351C engine. These lines are sold in pairs.

Reproduction transmission cooling lines made of stainless steel for the Mercury Cougar equipped with the FMX automatic transmission and 351C engine. These lines are sold in pairs.

Reproduction transmission cooling lines for the Mercury Cougar or Ford Mustang equipped with the C-6 automatic transmission and 428CJ engine. These are sold in pairs.

Reproduction transmission cooling lines for the Mercury Cougar or Ford Mustang equipped with the 428 Cobra Jet engine and C-6 automatic transmission. These lines are sold in pairs.

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the C-6 automatic transmission and 428 Cobra Jet engine. These lines are sold in pairs.

Reproduction transmission cooling lines made of stainless steel for the late production 1970 Mercury Cougar equipped with the C-6 automatic transmission and 428 Cobra Jet engine. These lines are sold in pairs.

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Reproduction console shift assembly for the 69 - 73 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm, seals and hardware. Replaces Ford part numbers: C7ZZ-7210C C7ZZ-7A306A C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Factory engine block spacer plate for 1969 1970 351W and 351C engines FMX (code X) and C6 (code U) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions. There are probably two versions of this plate, we believe the the 1969 version did not have the indentations. Replaces Ford part number D0AZ-7007-A.

Reproduction engine block spacer plate for 69 - 73 Cougars or Mustangs with 351 engines and 3 or 4 speed manual transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions.

Reproduction engine block spacer plate for 1969 1970 351 engines FMX (code X) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too.  Replaces Ford part number D0AZ-7007-A.

Used transmission line adapter and check valve for all FMX transmissions. This fitting goes into the rear part of the transmission case and connects the rear most cooling line to the case. Has internal ball check valve to prevent fluid from back flowing. All FMX transmissions 1969-73 Mercury Cougar or Ford Mustang. The male threads going into the transmission case are 1/2-20 pipe threads.Replaces Ford part number C3AZ-7D174-A.

Rod used for locking the FMX transmission in "Park". Connects to the lower tab of the steering column and the FMX transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 14 inches long. The FMX, automatic transmission, was used on all 1970 Cougars with any 351 engine. Transmission code "X" on your door data tag. Replaces Ford part number D0ZZ-7E330-E. Casting number D0ZA-7E330-R.

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098

Original dipstick or in Ford speak "Indicator - Oil Level" for C4 automatic transmissions. Application for 1967-68 Mercury Cougar 1966-70 Ford Mustang with 289/302 engines and C4 automatic transmissions, code "W" on your door data plate.Ford part # C6OZ-7A020-B.

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

Reproduction transmission dipstick tube for 67 - 70 Cougars or Mustangs equipped with the C4 automatic transmission.Replaces Ford Part number C6AZ-7A020-B

RAT-BB Original equipment 3 speed top loader 3.03 transmission from a 1970 Mercury Cougar with engine code H - 351-2V or engine code M 351-4V only. Ford master part number D0ZZ-7003-C. *Note RAT-BB1 or RAT-BB2 could also be substituted.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X =...

Fits perfect! The collar that slips into the opening of the bell housing is very tight for a precise fit that will withstand high horse power motors.

Quality kit that offers precision fit, for use with your stock bell housing. Requires drilling of one hole as well as drilling and tapping of a second hole in your bell housing.

New manufactured transmission yoke for a T-5 5 speed transmission.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

Formed metal clip that holds the gear end into any transmission. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

1967-70 Cougars with any FE engine (390-2V, 390-4V, 427 GT-E, 428CJ, or 428SCJ) and with C6 automatic transmission or manual transmissions.  Ford part #: C3AZ-7007-D.

Grade B used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This cover will have some rust and a dent or creases. Find the Grade A cover here.

Reproduction inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch.Replaces Ford part number C3AZ-6366-A.