All Available Parts - 1972 Ford Mustang

Perfect fit, great reproduction. These plastic discs are found on all 69-70 convertibles on the rear of both decor and xr7 interior levels. We are unclear as to all the "exact" applications on all years and models but one application we have verified is the fronts of 1971 - 73 Cougars equipped with standard interior. The reason the standard interior 71-73 Cougars came with these is that the door panels were very thick on the 71-73 decor / XR7 models and quite thin on the standard models and...

Bracket that mounts to firewall for accelerator shaft. 1971-73 Mercury Cougar and Ford Mustang. 

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and the 60 Watt Kenwood version of this speaker are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Rated at 30 watts peak power and 4 ohms.  Nice upgrade over the low wattage originals. Sold as a pair only. Replaces Ford part # C9ZZ-18808-A.   These pictures show what every 69-70 door panel looks like on the...

Reproduction window crank used on front doors of cars produced after 10-1-71 with no factory door speakers. Replaces Ford part number D2AZ-7630322-AOriginals have a casting number of D3AB-6523342-AA.

Reproduction Left Hand / Driver Side Outer Door Handle for the 1971, 1972 and 1973 Mercury Cougar or Mustang

Reproduction Right Hand / Passenger Side Outer Door Handle for the 1971, 1972 and 1973 Mercury Cougar or Mustang

Tested and working emergency or parking brake indicator switch. Foot parking brake switch found on 1971-73 Mercury Cougar and Mustang. This particular switch is also found on various other Ford/Mercury products starting in 1970. Ford part number D0AZ-15A851-A.Includes bolt to attach to emergency foot brake.

This reproduction power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid. This relay can also be used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.Will replace D1AZ-14677-A, AND C1AF-14677-A but will not be an exact fit

If your original is pitted or has come apart this will easily snap in place to remedy the problem. The finish on the repro differs a little from original.

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position.  These horns are close but not actually correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used D0DF-13802-A Lo /...

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Used water pump pulley used on 1970-73 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. This pulley is 5-15/16 inches in diameter. Pulley stamped C9OE-8509-F.

Single sheave pulley 6-61/64 inches in diameter. This pulley is designed to run on the inner most belt plane next to the water pump. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches. Applications:1970 Boss 302 Eliminators with power steering**1970 351 with power steering**1971 - 1973 351 engines with power steering or with idler pulley without air conditioning* Ford casting number D1AE-8509-BA....

Used pair of lower radiator brackets as taken from any 1971-73 Mercury Cougar or Ford Mustang. Additionally these will also fit 1970-71 Ford Torino / Fairlane and 1970-71 Mercury Montego / Cyclone. Should be for all engines. 250 6 cylinder, 302, 351, and 429. Right and left are different, plan on purchasing the insulating rubbers, they may not always be included. Ford part numbers D0OB-8052 or D0OZ-8052-A for passenger side, D0OB-8B381 or D0OZ-8052-B for the driver side. Check out our video on...

Concours for 1970 351C-2V and 351C-4V with correct ink stamped Ford script, 17 1/2" long including the 90 degree bend. Connects PCV valve to carburetor spacer plate. Other parts houses list this as a 71-73 but the 71-72 is 25" long (so it can reach to the front of the driver side valve cover) on both the 2V and 4v 351 Cleveland and this hose will not reach. This will work for the 1973 Q-code 351C-4V as the 73 mates to a metal tube and is only 11".This hose was originally installed from the...

Clips or clamps for attaching the 3/8" hard fuel lines to the body of any 1968-73 Mercury Cougar or Ford Mustang. Clips only, save your attaching body bolts. Sold in packages of 4 clips as shown. Will work on 1967 cars if you change to 3/8 lines. 1971-73 Cougar owners can use item 27565 attaching bolts, they are the same as the fuel tank mounting bolts. See related items. Replaces Ford 354663-S8

New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out our video on rebuilding your shifter below: ...

Rechromed 1967 deluxe shifter button. Unique to the deluxe faux leather wrapped T handle shifter starting in 1967. One year only design, this one has a convex button for you thumb. Starting in 1968 the button was more rounded to comply with the added safety features mandated in 1968. Core deposit is required, fully refundable with returned 1967 deluxe button. Ford part number C7ZZ-7C488-B. Check out our video on rebuilding your shifter below: ...

Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang

Reproduction thin firewall insulation pad with clips for the Mercury Cougar or Ford Mustang. This unit will fit both the A/C and non A/C Cougar or Mustang.

Black ABS plastic replacement kick panels without speaker pods. Sold as a pair. Reproduction kick panels made for 1971-73 Ford Mustang, but will fit a 1971-73 Mercury Cougar OK.

Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.

Replaces grommet in chrome oil cap with PCV valve. Inside diameter is 37/64". Replaces Ford part #: C8AZ-6892 or C8AZ-6A892-A.

A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part number D1WB-6502344, D2WB-6502344, D3WB-6502344. ...

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part numbers D1WB-6502345, D2WB-6502345, D3WB-6502345.

Good used console clock surround bezel with no cracks, or peeling chrome. Engineering number on the backside reads D1ZB-15017-AA

Used metal dash support brace for all 1971-73 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 10 inches long. Replaces Ford part numbers D1ZB-6504672-A.

Finally, a reproduction radio knob set for your 1971-73 Mercury Cougar or Ford Mustang! These little units are very hard to find in NOS form or good used condition with flawless chrome. Most knobs are peeling bad enough to cut you if you are not being cautious. It's often little detail pieces like these that separate first and second place at car shows. These knobs do not fit aftermarket radios.Replaces Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting #...

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out this video Still have riv-nut questions? Here are riv-nut answers! ...

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

New mirror glass, for the passenger side on practically any 1969-73 Ford with painted sport mirrors. This is the convex style of mirror, think "Objects in mirror are closer than they appear". Nice fit, exact shape of originals. Dimensions: 4 3/8 x 2 7/8 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video Check out this video ...

Pair of reproduction brackets and rods for the sun visors in the Mercury Cougar or Ford Mustang. *NOTE* These units will also work for the 1971-73 Ford Mustang fastback (sport roof).

For 351 Cleveland or Windsor when equipped with the "Flame Arrestor" PCV Valve. Also fits multiple applications with 1" hole in steel valve covers in which the PCV valve presses into. Inside diameter is 23/32". Replaces Ford Part #: C8SZ-6892, C8SZ-6A892-A or 381898S.

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

New foam insulation for the lower tube of the steering columns. Can be used on fixed and tilt columns, from 1968-73, on all Mercury Cougars, Ford Mustangs, and most all other Ford steering columns with a lower tube with inside diameter of 1-5/8 inches. The originals have almost always disintegrated. Adhesive probably isn't needed, but we recommend just a little drop of something to hold it in place. This is a dense foam insulation ring. DIY guys, this material can be found in bulk at home...

12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.

Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...

Used lower steering column shaft for 70 - 73 Cougars and Mustangs with a fixed column. Identified by length, and the round style lower flange. 1968-69 lower flange is slightly smaller with flat sides. Overall length is 16-3/8 inches.

Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place.  Ford part # D1AZ-3518 or E2AZ-3518

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Hooped support bracket only, there is also a large main bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3B139-A.

Used bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Main bracket only, there is also a hooped support bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3676-A.

Used wiring harness retainer bracket for mounting the steering column bracket, on any 1973 Mercury Cougar or Ford Mustang. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. Basic Ford part number 14A163.

Used flat headed stove bolt and nut, for attaching the two steering column mounting brackets together. Brackets for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Two needed per installation, sold individually. This is a 3/8-16 square neck bolt and nut. Ford part number 384527-S2.

Used lower steering column mounting bracket at firewall, for any 1971-73 Mercury Cougar or Ford Mustang. Rubber seal will need to be replaced, see related items for rubber seal.  Ford part number D1ZZ-65017A50-A.

Used upper steering column shaft for a fixed steering column on the 1971-73 Mercury Cougar or Ford Mustang. As shown, will need retainer clips and various C-clips and or Snap rings. Inspected for good threads for attaching the steering wheel. About 21-3/8 inches long. Starting in 1970, Ford had a "nail" type head. Ford part number D1ZZ-3524-A.

Correct nut that is designed not to come undone.

Reproduction reinforcement plate designed to weld onto the lower control arms. Sold individually, we are not sure that you would want to even buy one of these. They don't fit very well, and are not contoured to any lower control arm on the market. You will be bending these to fit, prior to welding. *Note - This is a non-returnable item. 

D2OZ-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1972 - 1973 Mercury Cougar and Ford Mustang with 351 engine and automatic FMX transmission, code X on your door data plate tag. Ford master part number D2OZ-7976-A.

Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. D2ZP-7A040-A version also available, we have a good supply of the updated 1972 version. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos.  This housing will not fit full sized Ford Mercury cars that have an FMX,...

Brand new flex plate for all 1969 - 73 Mercury Cougar and Ford Mustang with 302 / 351W / 351C engines, and C4, C6, or FMX transmissions. Comes complete with new starter ring gear installed as shown.*Note - Fits common torque converter bolt pattern of 11.40 inches. In 1972 there was a unique C6 torque converter with a 9.50 inch bolt pattern. 

Good used OEM flex plate for all 69 - 73 Mercury Cougar and Ford Mustang with 302 / 351W engines, and C4 or FMX transmissions. Not for use on a 1968 with 302. The starter ring will show wear and some will choose to replace, others have removed the starter ring and just turned it around so the unused portion of the ring will now contact the starter drive gear. ...

New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S

Set of 6 new correct bolts for attaching the FMX transmission to 351 engines. Fits all 1967-73 Mercury Cougar and 1967-73 Ford and Mustang with transmission code X, or FMX automatic transmissions. Quality fasteners from AMK.

Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. C9ZP-7A040-A version also available for slightly more money. Exact same part, just got updated for some engineering or manufacturing reason. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos.  This housing will not...

Cork pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Rubber gasket also available.

Rubber pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Cork gasket also available.

Transmission pan gasket for the FMX transmission on any 1969-73 and 1969-73 Mercury Cougar and Ford Mustang.

Basic C6 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C6 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that U code C-6 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.

Basic C4 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C4 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops. 

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Tall style filter for C4 transmissions.  Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.

Replacement tail shaft bushing, for all 1964-73 C4 transmissions.

Used automatic C6 transmission flex plate from a Q code 351CJ engine. All of the Q code automatics, or 351 Cobra Jet engines, came with this flex plate for mounting a specific torque converter. This flex plate has the torque converter mounting holes on a 9-1/2 inch pattern. Sold in used condition, may need a fresh ring gear. The current ones in stock are serviceable, with little to no damaged starter teeth on the ring gear.Ford part number D1ZZ-6375-C.

New C6 automatic transmission flex plate for use on 1972-73 Ford 351CJ engines and OEM Ford torque converter for 351 Cobra Jet. 164 teeth on the ring gear. *Note - this flex plate has a special bolt pattern specifically for the 351CJ torque converter as supplied when the cars were new.

Reproduction ring gear for 164 tooth fly wheels and flex plates as found on 1968-73 Mercury Cougar and Ford and Mustang. Quality new ring gear, check Youtube for installation instructions. 

Quality reproduction for all 1969-73 Mercury Cougar and Ford Mustang with FMX automatic transmissions. This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug and wire that will not be utilized when used on a 1969-71. All but one plug will be utilized on the 1969-71 applications. This plug and wire is not needed and can either taped off or clipped. Replaces original Ford part numbers C9ZZ-2A247-C,...

We've found that these are being manufactured to the wrong specs and are working with the supplier to correct the issue. This reproduction radiator / core support assembly includes the lower crossmember and is the very best one made! The outer width on the frame rails for the hardtops is 35-1/2 inches, a convertible has a width of 35-1/4 inches. A good body man should be able to make a hardtop core support fit a convertible, but know that it is different. We generally have 4-6 convertibles on...

Good quality reproduction front cross member for your 71 - 73 Cougar or Mustang. This is the frame / body piece that goes underneath your core support and receives the front ends of the strut rods. Sold as a stand alone part and does not come with strut rods or any strut rod hardware.Width: 34.75"Diagonal from outer bottom corner to outer top edge: 5"

Straight Monte Carlo Bar in a black finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering.  It will also help reduce the chances that your shock towers will develop stress cracks over time. Note: Not for A/C or Convertible applications. This product will not clear the distributor or A/C Compressor.  Replaces Ford part # D1ZZ-16A052-A. "Times New Roman"">...

Good for all 71-73 Cougars and Mustangs. This extension extends from the passenger side rear fender apron to the top of the cowl.This rear fender apron extension is a great choice for your damaged, rusted or missing panel. Made from stamped steel, just like the original. The extension fits in place between the passenger side rear fender apron and the top of the cowl. It provides for a sturdy, stable mounting area for the far rear top fender bolt and the rear hood hinge bolts. ...

Good for all 71-73 Cougars and Mustangs. This extension extends from the driver side rear fender apron to the top of the cowl.This rear fender apron extension is a great choice for your damaged, rusted or missing panel. Made from stamped steel, just like the original. The extension fits in place between the passenger side rear fender apron and the top of the cowl. It provides for a sturdy, stable mounting area for the far rear top fender bolt and the rear hood hinge bolts. ...

Reproduction Crossmember / Under Engine for the 1971 - 1973 Mercury Cougar / 1971 - 1973 Ford Mustang 

Two-piece Stainless Rear Axle Brake Line Set 71, 72 & 73 Mercury Cougar and Ford Mustang with the 8" or 9" Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help...

Two-piece OE-Style steel Rear Axle Brake Line Set 71, 72 & 73 Mercury Cougar and Ford Mustang with the 8" or 9" Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for added protection. ...

This is a reproduction long front and rear floor pan. Will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but this will work for all years.

This is a reproduction long front and rear floor pan. Will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but this will work for all years.

Sold as one-seat set including one bottom cushion and one backrest cushion.

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This extension holds the inner spring tube in place on the 70 - 73 column.Ford part number: D0AA-3790-CW

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Used lower steering column shaft for 71 - 72 Cougars and Mustangs with a tilt column. Measures 15-3/4 inches overall length. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Replacement seal with boot for all 1965-73 C4 Ford transmissions. Tail shaft and slip yoke seal. 

Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions. 

Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the FMX transmission valve body for all 1969-72 and 1969-72 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.* Note - 1973 has a different shift kit, see related items.

Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford. 

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Starting in 1972 the 'Fasten Seat Belt' warning light was relocated to the center of the dash for visibility of all occupants of the vehicle. This is a tested, and working seatbelt warning light fits into the steel holder on the instrument clusters of all 1972-73 Mercury Cougar and Ford Mustangs.Ford part number D2ZB-10C859-AA. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50%...

Used wiring harness that goes into the shifter bucket for any 1971-73 Mercury Cougar or Ford Mustang with C6 transmission. This is for the PRNDL light on your shift lever. Automatic C-6 transmission only code U on your door tag. FMX transmissions had the neutral safety switch installed in the shift bucket. Rare part, only found on Q code engines and select H code engines. D1ZZ-15A808-A, D1ZB-15A808-AB, D2ZB-15A808-AA This icon means that we're looking to buy this part!WCCC is a buyer of used...