All Available Parts - 1967 Ford Mustang

Basic C4 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C4 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops. 

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Tall style filter for C4 transmissions.  Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.

Replacement tail shaft bushing, for all 1964-73 C4 transmissions.

Reproduction ring gear for 157 tooth fly wheels and flex plates as found on certain 289 and 302 engines in 1967-68 Mercury Cougar and Ford and Mustang. Quality new ring gear, check the Youtube for installation instructions.

Reproduction ring gear for 184 tooth fly wheels and flex plates as found on big block 1967-71 Mercury Cougar and Ford and Mustang. Quality new ring gear, check the Youtube for installation instructions. Typically, the engine sizes would be 390, 410, 427, 428, and 429 cubic inches.

Replacement seal with boot for all 1965-73 C4 Ford transmissions. Tail shaft and slip yoke seal. 

Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions. 

Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the C4 transmission valve body for all 1967-67 Mercury Cougar and 1967-69 Ford and Mustang. This is a standard shift rebuilding kit for your stock valve body.

Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford. 

Used steering column release rod which is attached to the vacuum motor and lock pin, and also pushes the neutral safety switch.

This reproduction radiator support crossmember is correct for the 1967-68 Mercury Cougar and Ford Mustang, but will work on any 1967-70 Cat or Pony.Replaces Ford # C7ZZ-6510852-B or C9ZZ-6510852.

Reproduction radiator / core support for Mercury Cougar and Ford Mustang. This is the very best one made! Replaces Ford part # C7ZZ-16138-B and C7ZZ-6510852-B together.

These black Monte Carlo bars are equipped with Heim joints for smoother operation. Replaces Ford Part # C7ZZ-16A052-BJB.

Straight Monte Carlo Bar in a black finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C7ZZ-16A052-ARB.

Straight Monte Carlo Bar in a chrome finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C7ZZ-16A052-ARC.

Curved Monte Carlo Bar in a black finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C7ZZ-16A052-BRC. ...

Curved Monte Carlo Bar in a black finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford Part # C7ZZ-16A052-BRB. ...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

This is a tension spring that defaults the steering wheel to up and or tilt away position. The spring in the 1967 Column is not as strong nor as tall as the 1968 or 1969 column spring.Spring Length: 2 5/16" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1967 tilt-away steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This Screw fastens the plastic guide for turn signal wires next to column under the cone by steering wheel.

One year only bracket used on both fixed and tilt column cars.

Reproduction pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and 2 - 4 are required per car. Pin is custom made on short runs and is very difficult to find. .001 undersized, and with 8/32 threads instead of 6/32 like the originals. Newer pin removal tools will fit. Replaces Ford part # C7SZ-3D739-A. Removing pivot pins on 67 - 69 tilt away columns: Work on the upper knuckle pivot pins as there is room...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used Transition cover for the 67 Cougar or Mustang tilt steering column. This flange is different from 68 - 69. The 1967 flange does not have an inner tube to bolt to. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Reproduction vacuum reservoir for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This is a 1967 only design that didn't have mounting bolts on top like the later versions, they used a side mounting bracket.NOTE: You will need to use the mounting bracket from your old can, these reproductions do not come with one. *NOTE* WCCC services all FoMoCo tilt...

Lower steering column mounting bracket. 1967-68 Mercury Cougar and Ford Mustang. Right and left halves with original fasteners. Rubber gasket sold separately.Ford part number C7ZZ-65017A50 and C7ZZ-65017A51.

Reproduction turn signal switch connector for your 67 Cougar or Mustang. Work with either tilt or fixed columns. This is the connector that attaches the turn signal switch to the main dashboard wiring harness.

Used turn signal switch connector for your 67 Cougar or Mustang. Work with either tilt or fixed columns. This is the connector that attaches the turn signal switch to the main dashboard wiring harness. OEM was a white colored plug,the Scott Drake reproduction is black.. 

C7ZZ-652220-B Restored, stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Passenger side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually.NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to apply too much pressure, causing unwanted bending.

Used plastic rocker moulding clip for 1968 Mercury Cougar and 1967-68 Ford Mustang. Used clip, originally pop riveted onto the rockers. Sold individually. Ford part number C7ZB-6510182-A.

Good used five piece windshield moulding / trim set as taken from a parts car. Finish will be dull and some pieces may have minor scratches, but overall, this set is ready to install and will look decent as is. Ford part numbers for these pieces include: C5ZZ-6503136-B, C5ZZ-6503137-B, C5ZZ-6503144-B, C5ZZ-6503145-B, and C5ZZ-6503148-D. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. ...

The trim at the top of the windshield on the left hand side.Ford part number C5ZZ-6503145-B

Used passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece is suitable for your lower quality daily driver or a great piece for a high quality restoration.Ford part # C5ZZ-6503144-B. 

This good used original lower windshield moulding / trim has been carefully inspected to be free of small dings and heavy scratches. It will have very light scratches consistent with a classic of this age but nothing a do it yourself type could not bring to show quality on his own. This trim piece is perfect for someone wanting a trim part ready to install on their very nice driver or occasional show car. Much better fit than "offshore" reproductions. Ford part # C5ZZ-6503148-B. *NOTE* Keep in...

Used driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang. These are suitable for restoration and for use your daily driver.Ford part # C5ZZ-6503137-B.

Used passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece will fit right in on your daily driver or is an excellent candidate for those of who like to restore your own parts.Ford part # C5ZZ-6503136-B.

Restored five piece windshield trim set has been restored beyond the original luster. Keep in mind only cores with minor dings, dullness and scratches can be accepted. Kinked, gouged, and flattened cores will not be credited. This windshield moulding set fits the 1967-1968 Mercury Cougar as well as the 1964 1/2 - 1968 Mustang Coupe and Fastback. Ford part numbers for these pieces include: C5ZZ-6503136-B, C5ZZ-6503137-B, C5ZZ-6503144-B, C5ZZ-6503145-B, and C5ZZ-6503148-D. *NOTE* If...

Restored drive side upper windshield moulding, fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustang coupes.Ford part number C5ZZ-6503145-B.

Your original decades old trim will look fine... Until you place it next to a quality paint job.Ford part number C5ZZ-6503137-B.

Restored passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece is considered over restored because of the high luster and will make your Cat or Pony absolutely POP!Ford part # C5ZZ-6503136-B.

Restored passenger side (right had) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece will look right at home gleaming in the sun on your mint condition Cat or Pony and will definitely make your ride POP!Ford part # C5ZZ-6503144-B.

This restored OEM stainless steel lower windshield moulding / trim has been restored to a level far beyond NOS. It has been polished to a mirror like finish that is brilliant and gleaming. The term "over restored" could be applied to this part because back in the day FORD never spent the time we invested into polishing this piece. Original parts like this one always fit and look superior to "offshore" reproductions.Ford part # C5ZZ-6503148-B.

NOS driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503137-B.

NOS passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503144-B. 

Used seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1 or Ford Service part number D1AZ-10B924-A

Used on 1967 Mercury Cougar and Ford Mustang for the air conditioning, located under the dash to the back of the ignition switch. 25 amp circuit breaker, identified in the Ford MPC as part number C5AB-14A065-F or C5AZ-14526-C. It is 1.25" x 0.80". Box is marked FASCO Type 4110. 25AMP 12V. Attached mounting tab is included.These are tested and guaranteed to work.

Concours Correct Throttle Linkage Rod, 13 1/2" long, S code 390-4V, W code 427-4V, and R code 428CJ with factory 4 barrel HOLLEY carburetor, with out speed control.Replaces Ford Part # C8ZZ-9A702-A

Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: c5zz-9a702

Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: C5ZZ-9A702.

Direct replacement H pipe only for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds that includes the spacer valve on the passenger side. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 390 or 427 engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail...

This direct replacement H pipe only for any 1967-68 Mercury Cougar or Ford Mustang equipped with either the 289 or 302 engine and stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds that includes the spacer valve on the passenger side. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 390 or 427 engine. We also sell this H pipe in a 2 inch...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 289 or 302 engine. We also sell this H pipe in a 2 inch diameter and have OEM style dual exhaust systems...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Right side axle, 28 spline 31-1/8 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

Left side axle, 28 spline 27-1/16 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs.*Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

Also called a pumpkin, 3.00:1 open ratio. Check your door tag under "Axle". 1967 code 1 1968 code 5

Also called a pumpkin, 2.79:1 open ratio. Check your door tag under "Axle". 1967 code 0 (zero) 1968 code 2

Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare 9 inch axle housing with proper axle pad spacing, vent location, brake line attaching, and rear fill plug. Correct for all early 1967 big block Cougars. Over-sized shipping length.Axles used: Passenger side - 31-1/8 inches long, Driver side 27 inches long.

Also called a pumpkin, 3.00:1 open ratio. 1967 9 inch third members did not originally come with fill plugs. The back of the housing had the oil fill plug. You can mix and match 9 inch assemblies from 1967-1970, just make sure that you have at least one fill plug. Check your door tag under "Axle". 1967 code 1

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

Mounts on floor pan above the center of the rear axle over 3rd member on small block cars with 8 inch rear ends. Mustang only, will not fit a Cougar.Replaces Ford part #: C5ZZ-4730-B orC3AZ-4730-B. Customer Comment:Thank You Don and WCCC,Copy Cat's almost done!Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product.Without their patience and understanding along with a great selection of parts I wouldn't have her in such great shape.Thanks guys, along...

Sold individually, two required per car. Replaces Ford part # C3DZ-4730.

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new 4 pinion Trac-Loc unit, new Motive ring and pinion gears, new Timkin bearings, new crush sleeve, new bolts, and new seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. There are various ring and pinion (gear) ratios and axle splines available, if you are unsure of what you need it is best to call (503) 463-1130 for your order. This is a drop ship item. *Note - New...

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For use with 28 splined axles, but can be custom...

Limited slip 9 inch Ford third member rebuilt with all new or reconditioned parts. Rebuilt 4 pinion Trac-Loc unit, with new clutches, steels, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using standard 9 inch cases with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit was used in Cougars and Mustangs, but also any other Fords...

Limited slip 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and new a seal. Rebuilt using the standard 9 inch case, with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it works for any other Mercurys or Fords with a 9 inch...

Limited slip 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967-1973 standard 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used on any other Ford or Mercury with a 9 inch drop out center section. Because of all the various ring and pinion...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch case with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it can also be used for any other Ford or...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a 1967-1973 nodular 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used in any other Ford or Mercury with a 9 inch drop out center section. Because of all the...

Limited slip, nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Used modern design Detroit Locker unit, new Richmond ring and pinion gear, new Timkin bearings, new selective size sleeve, new bolts, and new seal. Rebuilt using 1967-1973 nodular 9 inch cases with oil fill plug, for 28 or 31 splined axles. This unit was used in 1967-73 Cougars and Mustangs, but it also came in any other Fords or Mercurys with a 9 inch drop out center section....

Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually

Gasket for sealing the 8 inch third member in most corporate Ford rear ends. Typically found in all 1967-68 Mercury Cougar and Ford Mustang with 289 or 302 engines. Exception for Mustangs with the GT option, those cars would have had 9 inch rear ends.

[No Description Provided]

Reproduction rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1968 Mercury Cougar and Ford Mustangs. New part with a fine threaded stud, also called a pinion bumper. The correct casting number is seen on this rubber axle bumper is C3AA-4906-C, this version has fine threads. The version most often seen on the 1969-70 is C9OA-4906-A. It will have a course threaded mounting stud.

Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Axles used: Passenger side - 31-1/8 inches long, Driver side 27 inches long. Bare housing with proper axle pad spacing, vent location, and brake line attaching. For all 1967 late big block Cougars and 1967 Mustang GT. Over-sized shipping length. This is the late 1967 housing that incorporates the oil fill plug in the third member or pumpkin. *Tip* If you are looking to strengthen your 1967-68...

Correct spring, black phosphorus plated. Does not have the same tension as original spring. We also have a Concours spring that has the correct tension. Replaces Ford Part #: C5ZZ-9737-B.*Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

Higher quality and higher tension spring than the spring offered by most Mustang/Cougar parts dealers. Replaces Ford part #: C5ZZ-9737-B or C7ZZ-9737-B

Great little kit that is a big time saver! Correct in detail, every 40 year old Cougar needs this kit! Replaces Ford Part #: C5ZZ-9A702-MK.

Bare housing with proper axle pad spacing for all 1967-1968 Cougars with 289 or 302 engines. Over-sized shipping length. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. This axle housing was used starting about mid 1967. It does not have the fill plug in the rear of the housing. * Important - Please check your car to verify that your 8 inch third member has a fill plug. Replaces Ford part number C7ZZ-4010-E. ...

C3AZ-4730-B Rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1970 Mercury Cougar and Ford Mustangs. Good used part with solidly mounted metal threaded stud. Pinion bumper. The casting number seen on the 67-68 is C3AA-4906-C, this version has fine threads. The version most often seen on the 69-70 is C9OA-4906-A. It will have a coarse threaded mounting stud. Two of these were used on certain 1967 Shelby Mustangs with traction bars.

Bracket mounts to 9 inch third member. Will not have heavy corrosion as found on Midwest and Eastern cars. Not notched like later years of snubbers. Correct for 1967 Mercury Cougar and 1965-67 Ford Mustang. Rubber bumper sold separately - C3AZ-4730-B rubber carrier bumper. Picture - 2007 40th Anniversary show in Carlisle PA. Bill Pratt with "Catvert".

Since we always claim to have parts nobody else does... This welds to the bottom side of the car just above the differential. When the rear suspension bottoms out, this is the plate the rubber snubber / bumper (mounted on the front on top of the dif.) makes contact with.

Mounts over rear axle ends into the body/frame, two required per car, this is the more pointed Christmas tree shaped version.Ford part # C6AZ-4730

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Spring perches are 43 inches apart on center. Complete rear end housing - drum to drum, with axles, and with pumpkin. 1967 EARLY 8 inch rear end housings with fill plug in the steel housing as seen...

Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare 8 inch axle housing with proper axle pad spacing, vent location, brake line attaching, and fill plug in third member. Over-sized shipping length.

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

This gasket goes between the rear axle flange and the backing plate on the differential. It fits all Mustangs from 1967 - 1970.

Rear axle vent bolt for the 67 - 73 Cougar or Mustang. This bolt serves a dual purpose, as it also holds the brake line bracket in place on the axle tube.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.