Interior

This set of knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and...

Perfect set of four radio knobs for your Mercury Cougar or Ford Mustang. Very hard to find with flawless chrome as most are peeling bad enough to cut you if you are not being cautious. Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob. D1ZZ-18830-A for the inner (balance / tone) knob, Ford casting # D1ZA-18A932-AA on the inner (balance / tone) knob.*TRIVIA* Did you know that Ford called the outer (balance / tone)...

Good used set of four knobs for your Mercury Cougar or Ford Mustang with a factory center console. These are plastic and much deeper than the non-console version. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 1968-70 AM radios with rear speakers and 1968-70 AM-FM radios, if you need the white spacer we offer it here. Our blow-out price is based on the fact that these are now available new! Knob length 1 1/2"Sleeve length 1 5/16" ...

Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Check out this video, showing how to replace the pin Check out this video...

NOS glove box light switch for the 69 - 70 Cougar or the 69 - 73 Mustang.

This very rare part is unique to the 1970 - 1971 CJ and SCJ C6. There was no 390 option in 1970 - 71. Sales were down on the CJ equipped Cougars in 70-71 making this one very hard part to obtain.  We have determined that this part only fits Mercury Cougar and Ford Mustang. Torino and mid sized Ford/Mercury use a different numbered part. Marked D0ZP-D. Ford Part #: D0ZZ-7A256-D. Check out our video on rebuilding your shifter below: ...

This very rare part is unique to the 1972 - 1973 351-4V / 351CJ with C6. We have determined that this part only fits Mercury Cougar and Ford Mustang. Torino and mid sized Ford/Mercury use a different numbered part. Marked D2ZP-AB. Ford Part #: D2ZZ-7A256-A. Check out our video on rebuilding your shifter below: ...

New manufactured Tilt / Tilt-Away cable for any 1968-69 Mercury Cougar or Ford Mustang with factory tilt steering column. All new parts developed by our in house steering column expert DW. Not created from used parts. The cable sheathing will not split or crack over time like the originals.Replaces Ford part number C9ZZ-3E520-A*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

Used Grade A pads are almost a little wrinkled and drawn looking.  We most likely will not be able to provide the color of your choice.

Grade B pads are will be wrinkled peeling away from the base. We most likely will not be able to provide the color of your choice.

This pad is in poor condition. You can actually modify a automatic pad to work with your manual transmission chrome bezel. *NOTE* If you have a clean example of this pad for sale we would like to hear from you!

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In In 1968 they were embossed with the iconic walking cat design. In 1967 they used a floral design which was the same left or right. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. These are for Standard level interiors only.

Good used metal portion of the door panel. If yours is bent or you're doing custom made door panels, you will need these.

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. These are for Standard level interiors only.

Used middle console support bracket. Held in place by 2 rivets midway under the console.

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

Grade A condition - passenger side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1968 Mercury Cougar, passenger side only. Found on XR7 and most Standard model Cougars. Grade A condition, will have supple vinyl without damage. minor or no de-lamination. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best...

This passenger side (right hand) moulding is correct for hardtop or coupe. On convertibles, the top portion is trimmed to allow it to slide under the sun visor bracket. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-6503598, engineering # imprinted on the back D1ZB-6503598 for 1971-72, D3ZB-6503599 for 1973. *NOTE* Excludes Mustang Fastback and Mach 1 models. This...

This driver side moulding is correct for hardtop or coupe. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Master part number D1ZZ-6503599.*NOTE* - Excludes Mustang Fastback and Mach 1 models. ...

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

Good used passenger side plastic trim that will need repaint, and the screw hole hidden behind the dash pad is almost always cracked. The 1969 XR7 and Decor models used the padded version.Limited colors available, please specify in the notes when ordering as to which color you want and we will do our best to accomodate you.

Dash pad attaching nut 8-32 threads original zinc plate and dichromate. 5 of these nuts are used to attach the dash pad to the painted steel upper dash panel  (D1ZZ-65044D90-A) on 1971-73 Mercury Cougar and Ford Mustangs. Sold individually.Replaces Ford part number 45271-S36.

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

Rare find in NOS condition! These are new, never used original manuals and no reproductions have been made. Limited quantity.

This is the second printing so it does include the xr7 package.

Reproduction Owners Manual for the 1968 Mercury Cougar

Has correct textured cover. Quality reproduction.

Good used original insulation pad as taken from a Western parts car. Used Jute pad that will not have any water or pest damage. These original pads are nice because they are made from a much more dense material (3.74 pounds) than the reproductions (.75 Pounds) and they have the factory perforated "knock out" sections for the optional speakers. A "Must Have" for show cars as the rear package tray fits better with this low profile material and no modern insulation resembles the original when...

There currently are no reproductions of this curved, thin package tray. Included with the tray are both slender strips of thin sound deadener / insulation. These package tray cover boards will not have heavy water damage, but will need paint. Replaces Ford part number D1WY-6546668-A.

Nothing matches the fit and feel of NOS. This will outlast the reproduction armrest three to one.

Base standard saddle arm rest on a 1967 Mercury Cougar or Ford Mustang, interior trim code 2F. Nothing matches the fit and feel of NOS. This will outlast the reproduction armrest three to one. Ford part number C7ZZ-6524140-A1F.

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake...

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

One required per car, mates to female version attached to the under dash loom. Same plug for tilt and non tilting columns.

Good used PCB that has no burns, corrosion or separating areas. The red PCB (printed circuit board) was used in the latter part of 1969 (from 2/17/69 on) and all of 1970. In 1969 if you had a white plug connected to the PCB it used a red PCB, if you had a black plug the blue PCB was used. Check out the video below on our new gauge tester: ...

Factory radio delete or block-off plate from a 1967-68 Mercury Cougar or Ford Mustang. Seldom seen part, roughly 5% of all 1967-68 Mercury Cougars were ordered without any type of radio from the factory. Similar story with the Ford Mustang, most owners added some sort of radio or stereo soon after delivery. The factory radio bezels were made from chromed pot metal, these radio delete plates are made from plastic and vacuum chrome plated. This used example pictured, has most of the plating...

This pad in unique in that it has four holes for the four warning lights found in cars with the convenience control package. In cars with no AC and no console the rectangular panel was located in the center of the dash face pad. You can expect a grade A pad to have no burns or cracks and still be pliable. Count on painting it as there is almost always fading after 50 years and we may not be able to supply the color you need. When you order mention the color you desire and we will try to to...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used grade B radio pad for the center console of the Mercury Cougar or Ford Mustang. This unit will be discolored from years of exposure to the sun and will be considered a driver quality at best. We rarely can provide the color you need due to the very limited supply we have. These pads always are separating from the metal backing to some degree. Other versions of Grade B might be cut for aftermarket radios. See pictures for some examples. Contact us to see if we have a pad that fits your...

Reproduction rag joint for the fixed steering column in the Mercury Cougar or Ford Mustang. This assembly is for the fixed column only and will not work for the tilt / tilt away steering column. Our reproduction rag joint comes assembled with the lower splined casting. 

Good used part without excessive rust or damaged rubber. For use with fixed column only. 1971-73 rag joints are different than the 1967-70 variety. The 1971-73 Cougar and Mustang steering box has a larger diameter shaft for attachment. Check out this video

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded integral steering box unique to the later Cougars. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Used rear console support bracket for the 69 Cougar or Mustang. Mounts under the leading edge of the storage compartment under the console.NOTE - 69 and 70 used different brackets

Used driver side (left hand) bare rear interior panel for the Mercury Cougar. This rear panel is just the plastic backing panel without the vinyl. We sell the panels this way so that you can save some hard earned money by reusing your existing vinyl from your broken or damaged rear interior panel. Keep in mind that these panels are almost 50 years old, so minor cracks and chips will usually be present.

Used passenger side (right hand) bare rear interior panel for the Mercury Cougar. This rear panel is just the plastic backing panel without the vinyl. We sell the panels this way so that you can save some hard earned money by reusing your existing vinyl from your broken or damaged rear interior panel. Keep in mind that these panels are almost 50 years old, so minor cracks and chips will usually be present.