Brakes

Reproduction brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. These have 1/2 inch holes in them, like the originals.Replaces Ford part number C4UZ-2028-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1076 WHITE Led Plasma back up light bulb for your 67-68 or 71-73 Cougar, Mustang or anything else you might have that takes an 1076 bulb. Please note that these bulbs are ground sensitive. Specs: Power: 7.5 Watts Brightness: 300 Lumens Total life expectancy: 30,000 hours 2" Tall (1 3/8" extends out of the socket) Comparison image - Click to view full-size: Check...

1967-68 and 1971-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175 As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 and will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003 bulbs).  Basically good for every car from 1950 to 1990 that uses a 1156...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

This after market adjustable proportioning valve is far superior to the original equipment. Fully adjustable for tuning front to rear brake bias. Requires some routing modifications of brake lines for proper fit. Includes adapter fittings. Replaces Ford part # C5ZZ-2B091-A, or C7OZ-2B091-B.Fits: 1967 Mercury Cougar 1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang 1968 Ford Mustang 1969 Ford Mustang 1970...

Used proportioning valve for the 1967-68 Mercury Cougar or Ford Mustang. This is a cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. For 1967 Cougars, this valve is most often found at the junction of the high pressure hose back at the rear end. 1968 had it connected to the distribution block on the driver side firewall. Will come with the C7OE-... stamped valve. Starting in 1969 the valves had a C9OE... Ford part number. These are used...

Reproduction proportioning valve for the Mercury Cougar or Ford Mustang. This is a cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. This valve is most often found at the junction of the high pressure hose back at the rear end, or later, found with the distribution block mounted on the driver side apron (inner fender). Replaces Ford part # C7OZ-2B091-B. Check out this video ...

Reproduction rear boot for your 67 - 69 Cougar or Mustang Midland power brake booster.

Reproduction front diaphragm for your 67 - 69 Cougar or Mustang Midland power brake booster.Diameter 7 1/4"

[No Description Provided]

Passenger side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1967-69 Mercury Cougar and Ford Mustang.

Fits any model that used the banded Midland-Ross booster. This Bakelite hub can be seen when you remove the dust boot. It is a very brittle fragile part that gets broken when you drop the booster, attempt to bleed the brakes with the engine running or install the wrong brake pedal.

This is the seal at the back of the booster on the Midland-Ross units.

New disc brake proportioning valve / distribution block seal and rebuild kit for the Mercury Cougar or Ford Mustang / Torino. Every 1967-69 Cougar, Cyclone, Torino, Ranchero and Mustang equipped with disc brakes needs this kit even if you are not leaking fluid yet. These little "O" rings are always "rock hard" after 40 plus years because the original O-rings are composed of a BASIC nitrile compound. After several years, the absorption of brake fluid will change the molecular structure of the...

Kit for rebuilding your drum brake distribution block on your Mercury Cougar or Ford Mustang. Special square O-rings are made from EPDM (Ethylene Propylene 70 Durometer) which is specifically designed to withstand chemical degradation caused by prolonged exposure to brake fluid.*Customer Feekback*"You guys are awesome, I couldn't find a rebuild kit for my Galaxie's brake distribution block anywhere else! Thank you!" Henry M.Check out this video ...

This all inclusive vacuum booster master rebuild kit is great for the do it yourself-er or the person that would like to retain their original case / housing. Also a great option for the out of country customer that does not want to pay expensive shipping to return a core. Keep in mind this will only work on a BENDIX unit with the crimped band. Also be aware that our rebuilt units we sell do not have 100% new parts as shown here as our builder will reuse multiple parts that can be cleaned up...

This all inclusive vacuum booster master rebuild kit is great for the do it yourself-er or the person that would like to retain their original case / housing. Also a great option for the out of country customer that does not want to pay expensive shipping to return a core. Keep in mind this will only work on a MIDLAND unit with the removable band. Also be aware that our rebuilt units we sell do not have 100% new parts as shown here as our builder will reuse multiple parts that can be cleaned...

Reproduction driver (left hand) side drum brake self adjustor repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Reproduction passenger (driver hand) side drum brake self adjuster repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Push on retainer for rear drum brakes. 2 or 3 of these were used to hold the rear brake drums onto the rear axle assembly during construction of your 1967-73 Mercury Cougar or 1965 - 73 Ford Mustang. While not necessary, these are a neat concours item. Sold individually.  Ford part number 372188-S

Reproduction emergency / parking brake retainer clip set for the Mercury Cougar or Ford Mustang. These units are sold in a set of 3.

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2" and is a very good copy of the original. Made in America.

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2".  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Wheel seal for both front disc and front drums, 1967-73 Mercury Cougar and 1967-73 Ford Mustang with V-8. Seals sold individually. Two of these are needed, one for each side on the front.

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1968-70 shaft which had a Ford part number of C8AZ-2478-A. This version uses a special spring clip. We also sell the 1967 shaft, which uses a hairpin clip and washer.

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1967 shaft uses a hairpin clip and washer on the end. We also sell the 1968-73 shaft, which uses a spring clip.Ford part number of C6AZ-2478-A.

Used shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. We do not have the spring clip available. Ford part number of C8AZ-2478-A. 

Used spacer or retainer, for the 1967-68 Mercury Cougar and Ford Mustang. This filter retainer spacer is made of aluminum and is for the Midland manufactured brake booster. It fits between the master cylinder and brake booster. Nothing beats original FoMoCo!The Ford part number may be C5AZ-2B157-A. 

Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.

Reproduction spacer kit for your 1967 - 1969 Cougar or Mustang Midland power brake booster.

This reproduction emergency / parking brake spring for the V8 Mercury Cougar or Ford Mustang is made from original Ford blue prints. This is the oblong spring that is painted RED like the originals, rests upon the parking brake cross bar link between the shoes.These springs came from the factory in either Red or Yellow.You can find the Yellow spring here.Replaces Ford part # C2OZ-2601. ...

This reproduction emergency / parking brake spring for the V8 Mercury Cougar or Ford Mustang is made from original Ford blue prints. This is the oblong spring that is painted YELLOW like the originals, rests upon the parking brake cross bar link between the shoes.These springs came from the factory in either Red or Yellow.You can find the Red spring here.Replaces Ford part # C2OZ-2601. ...

This kit contains all the replacement springs and hold downs required to do a professional job on 10" x 1-3/4" drum brakes. Kit includes enough parts for two wheels. *Hint - Use your camera phone to take pictures of your brake assembly prior to disassembly, and do one side at a time. Sort out and match all of the springs up exactly, they are side and position specific.*Note - Kit does not include hardware for rear emergency brakes.

Contains all the replacement springs and hold downs required to do a professional brake job on drum brakes, front or rear. Kit includes enough parts for two wheels.Fits 10 x 2, 10 x 2-1/4, and 2-1/2 inch drum brakes.*Hint - Use your camera phone to take pictures of your brake assembly prior to disassembly, and do one side at a time. Sort out and match all of the springs up exactly, they are side and position specific.*NOTE* Kit does not include hardware for rear emergency brakes. ...

Reproduction drum brake spring and hold down kit for Mercury Cougars or Ford mustangs equipped with 10"x2" drums. This kit contains all the replacement springs and hold downs required to do a professional brake job on 1969-73 Mercury Cougar or Ford Mustang 10" x 2" rear drum brakes. Kit includes enough parts for two wheels. *Hint - Use your camera phone to take pictures of your brake assembly prior to disassembly, and do one side at a time. Sort out and match all of the springs up exactly,...

Reproduction brake pedal hanger for manual brakes. Can be modified to work for power brakes.

This used brake pedal support bracket is the correct hanger for a 1967-68 Mercury Cougar or Ford Mustang with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint, unused condition. Ford part # C7ZZ-6501508-C. *NOTE* Manual brake supports are different. Manual brake supports have four threaded...

This used brake pedal support bracket or brake pedal hanger is for the Mercury Cougar or Ford Mustang equipped with power disc or drum brakes. We have carefully shown the mounting position of the pedal so you can drill your existing manual brake pedal hanger when converting from manual to power brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means...

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Reproduction brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a high quality replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford Part #: C9VY-13480-A.

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

This steel fitting mounts into the intake manifold and receives the vacuum hose that runs from the brake booster on 67 Cougars and Mustangs equipped with the 390 4V engine.