Body

Reproduction trunk wheel house seam cover for the Ford Mustang. I have actually never seen an original pair of these on a car, but they do serve a purpose if you are in the habit of cramming your trunk full of items you do not want scratched. These attach to the protruding seam where the inner and outer wheelhouse bond together and measure about 14" in length. You will have to modify these to fit your Cougar. Only sold in black. Replaces Ford part # C5ZZ-6531466-A.

Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size)Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video...

Reproduction upper cowl conversion panel for doing a RIGHT HAND DRIVE conversion on their 67 - 68 Mustang. 

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C7ZZ-6522800-C. ...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # C7ZZ-6522800-C.

Reproduction driver side (left hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.

Reproduction passenger side (right hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Sold as a pair, includes plastic fasteners. There are multiple manufacturers of this particular item and we feel after using them all on our own cars that we carry the best out there. Replaces Ford part #C7ZZ-6520530-A.

Reproduction medium blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed.*NOTE* There are two types of this trim found in the 1967-68, the smooth or rough texture. ...

Very correct reproduction with a quality chrome finish. The rear (quarter) window cranks are listed in the interior section. Keep in mind their are multiple makers of this part and this is the best. Replaces Ford part # C5ZZ-6523342-C.

Good used crank correct for 1967 XR7 or standard models. No obvious blemishes, driver quality. The Ford part # is C5ZZ-6523342-C, casting number as found on the back reads C7ZB-6523348-A. *Customer Feedback* Don, Lin and staff; Just to let you gentlemen know that I have received the 1967 XR7 saddle tan door panels you sent and I am extremely happy with the condition and the service! It has been less than a week since I ordered them and they arrived via USPS, as per requested, with a very...

These are correct for XR7 or standard 1967 models. Used handles are almost always pitted due to lack of use. These are different than the front in that they are held on with an Allen set screw and are shorter in length. Replaces Ford Part #: C5ZZ-6530322-A. *NOTE* We have no good used examples of these rear window cranks as they are very prone to pitting over the years.

Correct spare tire hold down wing nut for the 1967 Mercury Cougar or Ford Mustang. Replaces Ford Part #: B9AZ-1462-A.

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part #: C5AZ-6223370-A.

Good used tray that is not currently reproduced. Most people prefer the group 24 battery but for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting). Many that are not rotted have been cut to accept a group 24.

Good used group 24 tray for 1967 Mercury Cougar or Ford Mustang. Assembly line installed group 24 battery tray with holes for tilt vacuum canister. For those that want to keep it very original, this version is not reproduced. This is getting to be a hard to find part with no rot (will show pitting).

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

Very rare find in the original service replacement boxes dated 10-07-75. Sold as a pair.Ford part # C8WY-65502B20-A.Click on images to enlarge. ...

If your Cougar has to sit outside for any length of time this is a must. Not only will it protect from unwanted moisture but pine needles and other debris will be kept out. If your cowl already leaks then this is a great way to prevent the floors from rusting. Spring loaded T shaped fasteners make for instant installation and removal, attaches under grate bars so as not to damage paint. Very worth while preventative maintenance item.

Silicone and fasteners, everything needed for installation of our seat divider panel.

This listing is for the outer doors pieces only, Cougar and Mustang are identical. These original NOS FoMoCo parts fit better and will last longer than repro.Ford part numbers C7ZZ-6521453-A  and  C7ZZ-6521452-A

Good used original handle with no obvious pitting or blemishes. This handle was not used on the XR7. Found on 1967 standard model Cougar and 1967 base model Mustang. Ford casting number C7OB-6222614-A.*Note - 1967 Mustang with deluxe interior, i.e. brushed door panels, used a similar handle, but with Ford part number C7ZB....

These are the assemblies that your inside door handle attaches to and features all new components. They are gold cadmium plated to resist rust and corrosion. *NOTE* We have had complaints of these not fitting as well as originals therefore we suggest buying our used units. Rod retainers not included.

This is the assembly that your inside door handle attaches to and features all new components. They are gold cadmium plated to resist rust and corrosion. *NOTE* We have had complaints of these not fitting as well as originals therefore we suggest buying our used units. Rod retainers not included. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

New old stock driver side door handle the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. This handle is NOS, NOS doesn't always mean high quality plating. Includes mounting hardware and pads. Round button not included. Replaces Ford Part #: C4DZ-6222405-A

New old stock passenger side door handle the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. This handle is NOS, NOS doesn't always mean high quality plating. Includes mounting hardware and pads. Round button not included. Replaces Ford Part #: C4DZ-6222404-A

These two original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never been...

The same plastic lock rod grommet but with a nice chrome finish for an extra touch. Sold in pairs. Replaces Ford Part #: C5DZ-6221999-B or C5DZ-6221999-C.

C5AZ-6221850-A Door lock knob for all 1967 Mercury Cougar and Ford Mustang. Additionally fits 1965 Ford full size cars such as Galaxie and Thunderbird. 1966-67 mid sized Ford Fairlane and Mercury Comet. Sold individually. Nice used condition.

Yes, these were a dealer option available in the day. They cover the painted portion of your door sill that is not covered by the scuff plate. Great way to prevent scratches in your paint or hide existing scratches. Since they are made from stainless steel, you can polish them if and when they get scratched. These are sold as a pair, left is the same as right.  Ford part # C5ZZ-6513242-A 

These NOS sill plates always have some degree of shelf wear due to the many years they have been shuffled around. The biggest difference you will see with NOS vs. the two different levels of reproductions is the finish. The NOS parts are far less bright and less prone to showing hairline scratches. One other benefit is that NOS sill plates already have the FORD decal in place. Sold individually.

Chassis black aerosal paint for all 1967-73 Mercury Cougar and Ford Mustang engine compartments. High temperature (advertised up to 350°). Manufacturer boasts resistant to cracking and flaking, chemical resistant to gasoline and brake fluid (but don't let brake fluid accumulate). *NOTE* Chemicals can only ship UPS ground only. Please, no foreign orders or USPS shipping allowed.Check out our video below on chassis upgrades: ...

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Driver quality used left side or driver side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

3 1/8" Style Steel Wheel Spare Tire Hold Down. Available in Black or Chrome. Ford Master Parts Catalog indicates that this hold down was found on some 68 and 69 Cougars with SS Wheels. You may need to bend the ears in slightly to get them to fit properly inside the hole in the center of the wheel. Replaces Ford Part #: C8MY-1424-A.

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.

Used anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"