Body

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pins. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C7ZZ-6522811. ...

1967 Cougars used this cast iron hinge that weighs a pound or more over the 1968 stamped steel version. You may want to opt for a 1968 hinge if your goal is to lighten your car. You will shed about six pounds if you replace all four with a set of 1968 stamped steel Mercury Cougar door hinges. These used hinges usually need new pins and bushings, for the small cost of the new parts we suggest you purchase the Complete Hinge Rebuild Kit. Check out our hinge rebuild video below for more info. ...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them.Replaces Ford part # C7ZZ-6522810. ...

1967 Cougars used this cast iron hinge that weighs a pound or more over the 1968 stamped steel version. You may want to opt for a 1968 hinge if your goal is to lighten your car. You will shed about six pounds if you replace all four with a set of 1968 stamped steel Mercury Cougar door hinges. These used hinges usually need new pins and bushings, for the small cost of the new parts we suggest you purchase the Complete Hinge Rebuild Kit. Check out our hinge rebuild video below for more info. ...

Early 68 cars often used this 2 1/2" pin as well. Sold individually, four required per car. Replaces Ford part #: B9A-5943030-AA.

This cut to fit 4" pin will fit any 67 - 73 Cougar hinge upper or lower. Sold individually, four required per car. Check out our hinge rebuild video below for more info.

Kit replaces one side. Contains all necessary parts including pins, bushings, a new cam plate, spring, and roller to rebuild both upper and lower hinges. This kit is for the cast iron type hinges found on the 1967 and early 1968 Cougar.Replaces Ford Part #: C5ZZ-6522800-K.

Used on all 1967 lower hinges and 1968 cast iron lower hinges. Perfect replacement for the spring that loads the door position detent plate against the position roller. Springs are painted for corrosion protection. Sold individually, two required per car. Replaces Ford Part #: C0DZ-6421232-B.

Whenever you take on a door job, its always handy to have a few things available....a helper, a floor jack and a door hinge wrench. While a helper and floor jack might not always be available, a door hinge wrench is a valuable tool to have around when removing / setting a door. This Snap on obstruction wrench (google snap on part # S9608B) is specially curved to allow you to gain access to a few of those hard to reach bolts on your door hinges. We will loan this door hinge wrench for 60 days,...

Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.

These are the screws that secure the door latch mechanism to the door shell. These screws come with the attached crown headed lock washer, just like the originals, so be sure to tighten them down snugly to ensure that the screw head sits flush into the screw holes. Sold individually. Three required per door, six per car.

Steel stamped complete latch. See hardware for clips. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Used driver side (left hand) complete door latch assembly for the standard Mercury Cougar or Ford Mustang. This unit goes inside your door and catches on the door striker assembly on the door jamb. This latch does not have the tab for mounting the door ajar switch. See related items for "with door ajar". This C7OZ-6221813-A version is identified with the long tab for the key lock rod.Ford part # C7OZ-6221813-A. Check out our handy diagram below to find other '67-'68 door parts you may need....

Used driver side (left hand) complete door latch assembly for the 1967-68 Mercury Cougar XR7 or Ford Mustang with door ajar option. This unit goes inside your door and catches on the door striker assembly on the door jamb. Has unique tab for mounting the door ajar switch, which was part of the XR7 package. Optionally on standard model Cougar and Mustang with the convenience group option. Door ajar switch sold separately. This C7ZZ-6221813-A latch is identified by having the long tab...

Used driver side (left hand) complete door latch assembly for the Mercury Cougar XR7 or Ford Mustang with door ajar option. This unit goes inside your door and catches on the door striker assembly on the door jamb. Tested and inspected for excessive wear. This latch does have the ability to mount the door ajar switch, as found on all XR7 models. Door ajar switch sold separately. Must use the 1969-70 door ajar switch with this mechanism. Ford part # C9AZ-6221813-A. ...

Steel stamped complete door latch assembly that goes inside your passenger side door and catches on the door striker assembly. See hardware for clips. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Used passenger side (right hand) complete door latch assembly for the standard Mercury Cougar or Ford Mustang. This unit goes inside your door and catches on the door striker assembly on the door jamb. This latch does not have the tab for mounting the door ajar switch. See related items for "with door ajar". C7OZ-6221812-A version is identified with having the long tab for the key lock rod.Ford part # C7OZ-6221812-A. Check out our handy diagram below to find other '67-'68 door parts you...

Used passenger side (right hand) complete door latch assembly for the Mercury Cougar XR7 or Ford Mustang with door ajar option. This unit goes inside your door and catches on the door striker assembly on the door jamb. Tested and inspected, this latch does the have the provision for the door ajar switch as found on all XR7 models. Door ajar switch sold separtely. This will fit all years 1967-70, was used as a service replacement. Just has a shorter tab for the key lock rod. Must use...

Used passenger side (right hand) complete door latch assembly for the 1967-68 Mercury Cougar or Ford Mustang. This unit goes inside your door and catches on the door striker assembly on the door jamb. These are identified with the long tab for the key lock rod.  Does not include the door ajar switch, you can find it here. Ford part # C7ZZ-6221812-A. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar...

Steel door latch reinforcement repair kit. Countersunk bushings and screws for reinforcing the inside the door mounted latches on 1967-70 Mercury Cougar and Ford Mustangs. Kit has 6 machine screws and bushings, enough for both doors. The metal on the doors is very prone to cracking in the screw area for those latches.

Used original door latch rod for the interior push button lock on the driver side (left hand) of the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6521853-A.

Used original door latch rod for the interior push button lock on the passenger side (right hand) of the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6521852-A.

Often when your door will not latch this is the culprit.

Good Reproduction of the clear plastic door lock grommets. Sold as a pair. Replaces Ford Part #: C5DZ-6221999-B.

Polished stainless steel with correct internal black felt anti-rattle pad. Sold as a pair.

Plastic injection molded, chrome plated just like the originals. Sold as a pair. Replaces Ford part number C5DZ-6221850-A

Plastic injection molded, chrome plated just like the originals. Sold as a pair. Replaces Ford part number C5DZ-6221850-A

Made for Mustang but can be tweaked to work on Cougar. We advise you buy our good used rods. Replaces Ford part # C7ZZ-65213452.

Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1967 Mercury Cougar and Ford Mustang. 1967 door latches are unique, they have a short tab for the inside door lock knob typically. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown...

Made for Mustang but can be tweaked to work on Cougar. We advise you buy our good used rods.

Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1967 Mercury Cougar and Ford Mustang. 1967 door latches are unique, they have a short tab for the inside door lock knob typically. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers...

Convenient matched sets save costly locksmith work. Kits includes a pair of door lock cylinders. Comes with two keys. Includes door cylinder gaskets. If you don't mind have having a different key for the door locks, this product might just work out.Attention potential buyer! This item will likely give you problems and be a general disappointment. Reviews show that the fitment is fair, and you will not be able to have these lock cylinders re-pinned, to use your original Ford key. One...

These are so nice... The texture is exact, the rubber feel is right, the fit is perfect, the colors are correct "except aqua which is a darker than Cougar, Mustang color". These used to be very hard to find in good used condition, why bother with used when you can get them at this price. Sold as a pair.Replaces Ford Part # C8ZZ-6526656. *Customer Feedback* Don and staff; Just to let you gentlemen know that I have received the 1967 XR7 saddle tan door panels you sent and I am extremely happy...

These are so nice... The texture is exact, the rubber feel is right, the fit is perfect, the colors are correct "except aqua which is a darker than Cougar, Mustang color". These used to be very hard to find in good used condition, why bother with used when you can get them at this price. Sold as a pair Replaces Ford part # C8ZZ-6526656.

New, more accurate woodgrain as of 2019! These decals are cut to fit the 1967 door pull end caps. The 1968 end caps had a smaller woodgrain insert with a black border. We also sell a slightly smaller version of this kit for the 1968 owners. This kit also fits the reproduction end cap kit. Check out this video

Fits both left or right, sold individually. These have a higher degree of luster than the originals but are made of same material and weigh exactly the same as our NOS examples. Very little difference from our more expensive version which is made using original tooling. Ford Logo sold separate, sold individually, two required per car. Replaces Ford part # C5ZZ-6513208-B or C5ZZ-6513208-D.

These interchange left to right, they are a mirror image of one another. We recently did a side by side comparison of these so called "concours" sill plates and found very little difference when comparing them to the "economy" version... They both weigh .52 pounds, just like our NOS sill plates. They both have a high of luster, unlike the originals which featured very little "shine". We found the screw holes to be just a tad larger on the economy version but once the screw is inserted you...

Decent, used, driver quality part that will have scratches and dings consistent with a Cougar that has been on the road for decades. Even if we look through our pile and find the best we have it still will show wear, expect it to look just as ugly as the one pictured. Sold individually.

New Supplier Now Available! *Unlike our other sill plates, these are sold as a pair* Ford never made these in stainless but what a great upgrade! The advantage we see with these is that they do not dent or scratch as easy when you release your seat belt. They also can be polished easily (unlike anodized aluminum). These weigh 1.5 pounds each, triple of what the originals weigh. Sold as a pair only. *NOTE* There are two suppliers on these and we now carry only the Dynacorn...

Very nice reproduction, silver zinc finish like original. Correct texture and even an original type date stamped on the head. Comes complete with striker plate, shim, and screws. The only difference between the 67 Cougar and the 68 - 70 is that the 67 came with the 8-66 date stamp, the rest came with the 11-67 date stamp. Note: Some Cougars did not have date stamps from factory. Replaces Ford part # C5AZ-6222008-B.

Very nice reproduction, silver zinc finish like original. Correct texture and even an original type date stamped on the head. Comes complete with striker plate, shim, and screws. The only difference between the 67 Cougar and the 68 - 70 is that the 67 came with the 8-66 date stamp, the rest came with the 11-67 date stamp. Note: Some Cougars did not have date stamps from factory. Replaces Ford part #: C5AZ-6222008-A.

Reproduction polished stainless steel door strikers for your Mercury Cougar or Ford Mustang. This kit includes stainless steel hardware and will make your door jambs pop.Replaces Ford part # C5AZ-6222008-A.

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

This shim, also referenced to as washers, goes in the clutch portion of the drive gearbox to properly adjust the friction. Three shims (plus a hand crank) were originally supplied with sunroof cars.

This reproduction cowl vent repair panel for the driver side (left hand) of the Mercury Cougar or Ford Mustang addresses a common problem with these old Cats and Ponies. Rust in the cowl. Easy to install on the driver side, but takes more effort on the passenger side, especially if you have air conditioning. These panels are also called fresh air cowl vents or inner cowl vent repair panels. Another way to avoid doing expensive cowl repairs is to purchase our cowl cover.*NOTE*  While...

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

This is the aluminum emblem which mounts on the center of all scuff plates. Features raised script surrounded by "Product Of Ford" like original, adhesive backed and protective coating. Sold individually, two required per car. Replaces Ford part # C8ZZ-6513208-T.  Technically this is the version found on early 1967 cars, the late 67 and 1968 versions had a larger blue oval 'Ford', and did not have the 'Product of' line.

Holds both both the speedo cable and the parking brake cable in place with two self tapping bolts. Bolts not included, picture is for reference only. Part will have rust, but not severe.Replaces Ford part number 381821-S2 per the Chassis Assembly Manual 1967 page 17, 1968 Page 39.