Emblems

Reproduction barrel nut or insert for attaching "Cougar" fender script to the fenders. Each Cougar emblem uses 4 of these barrel nuts which insert into the fender first, and then the Cougar emblem. Additionally, these nuts also go into the C pillars for attaching the XR7 badge or medallion on each side. Two barrel nuts per side for the XR7 medallions. Barrel nuts sold individually. The install is basically the same as shown here: https://youtu.be/mcd788WUNns ...

Excellent reproduction of the passenger side 1967-68 Mercury Standard Cougar "Cougar" dash panel emblem. Nice reproduction with locating pins that attach to the padded dash panel on the passenger side of all 1967-68 Standard model Cougars. The factory originally installed these emblems onto the padded dash panel, and melted over the pins to the back. Carefully remove the padded dash (clips or screws) and break off the melted tabs on the back of the emblem. Clean pad and reinstall the new...

Reproduction passenger side 1967-68 Mercury Cougar "Cougar XR7" dash panel emblem with chrome XR7 highlights. Nice reproduction with locating pins that attach to the woodgrain dash panel on the passenger side of all 1967-68 XR7's (excludes the special edition XR7-G models). The classic Cougar community voiced their opinion that the original emblems with satin silver was nice, but the chromed "XR 7" lettering in chrome makes the dash 'Pop' (see comparison photo above). The factory originally...

Excellent reproduction of the passenger side 1967-68 Mercury Cougar "Cougar XR7" dash panel emblem. Nice reproduction with locating pins that attach to the woodgrain dash panel on the passenger side of all 1967-68 XR7's (excludes the special edition XR7-G models). You can view the photo above for a comparison between the satin and chrome versions. The factory originally installed these emblems onto the woodgrain steel panel, and melted over the pins to the back. The rear section of that...

Reproduction Center Grille Insert Background Decal for the 1967 and 1968 Mercury Cougar. This insert will need to be shaved down on 2 sides to fit correctly, do not force the insert into the grille, it will pooch up in the middle and not adhere correctly. The aluminum Mercury Man emblem can be popped out from the rear with a solid hit with a drift punch and hammer without causing damage. Check out our video, showing how to install this decal, along with some other handy grille restoration tips ...

This decal was used on the Standard model Mercury Cougar for 1968 and both the XR7 and Standard model Mercury Cougar for 1967. Will require slight trimming for perfect fit. If you place a piece of 80 grit sand paper (or file/emery board) on a firm surface you will be able to bring the height of the decal down with just a few strokes of both the upper and lower edge. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive...

New Custom White (unpainted) lock decal with silver lettering. This decal was used on the Standard model Mercury Cougar for 1968 and both the XR7 and Standard model Mercury Cougar for 1967. Will require slight trimming for perfect fit. If you place a piece of 80 grit sand paper (or file/emery board) on a firm surface you will be able to bring the height of the decal down with just a few strokes of both the upper and lower edge. Dear Lin Thurston, Hi, just wanted to let you know how...

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very...

Used Grade A condition 6.5 litre (390) aluminum fender emblem / badge for the 1967 Mercury Cougar. We rarely get these in fantastic condition and most of what we get looks like the one pictured with several small blemishes. Often, one of the two studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390. On other Cougars, they were used on those that came equipped...

Used Grade B condition 6.5 litre (390) aluminum fender emblem / badge for the 1967 Mercury Cougar. We rarely get these in good condition and most of what we get looks like the one pictured with several pits and small blemishes. Often, one of the two studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390. On other Cougars, they were used on those that...

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

Due to corrosion caused from the exhaust this used emblem will most likely have poor quality chrome. The emblem shown would be the very rare exception.

This is the aluminum emblem which mounts on the center of all scuff plates. Features raised script surrounded by "Product Of Ford" like original, adhesive backed and protective coating. Sold individually, two required per car. Replaces Ford part # C8ZZ-6513208-T.  Technically this is the version found on early 1967 cars, the late 67 and 1968 versions had a larger blue oval 'Ford', and did not have the 'Product of' line.

These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge was used until sometime between 11/22/66 and 1/28/67, after that, the individual letters were used.Ford part number C7GY-16098-BFord Casting number C7GB-16720-B ...

These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge was used until sometime between 11/22/66 and 1/28/67, after that, the individual letters were used.Replaces Ford part number C7GY-16098-B ...

These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge was used until sometime between 11/22/66 and 1/28/67, after that, the individual letters were used. Ford part number C7GY-16098-B ...

Amazing quality that surpasses any NOS or restored emblem you will ever see. This unique emblem was only used on the front fender extension (driver side) of the 1967 and 1968 Cougar. Replaces Ford part number C7WY-16604-A. Here's some info on the measurements for placement: 1. From the bottom of the Y to the right edge of the deck lid - 1.28"2. From the top of the deck lid moulding to the bottom of the Y - 0.18"3. From the top of the deck lid moulding to the bottom of the M - 0.73" Also, note...

Used Driver Side / Right Side Fender Extension Emblem for the 1967 and 1968 Mercury Cougar

New Old Stock "G" and "T" 1967 Mercury Cougar and Ford Mustang individual fender letters. There were two ways that the cars were called out as GT's. Two individual letters and a single box with "GT" inside. These letters were also used on 1970-71 Mercury Cyclone. Both letters sold together. Ford part number C7ZZ-16098-A and C7ZZ-16098-B.

This is a very nice reproduction that we have all needed for many years! You might want to buy a new Cougar walking cat emblem if you replace this background decal as it requires breaking the studs off your old emblem to get it off. Check out this video ...

These Mustang emblems have the incorrect pin placement for the 1968 Cougar so if you have original GT fenders you will have to drill new holes. Once mounted they look correct. Replaces the C7ZB... individual casting numbers. Licensed by FORD

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

Invest the big money elsewhere...Here is a NOS part we do not suggest paying the extra money for. These NOS emblems are not as good as the reproductions that cost less than half. The chrome is far superior, the studs stronger and the way they are assembled is much better on the reproductions. The type of person that buys these is doing a "very" original, concours restoration and will pay the extra money to avoid an "over-restored" appearance. These are sold singly only. Drive side part number...

Invest the big money elsewhere...Here is a NOS part we do not suggest paying the extra money for. These NOS emblems are not as good as the reproductions that cost less than half. The chrome is far superior, the studs stronger and the way they are assembled is much better on the reproductions. The type of person that buys these is doing a "very" original, concours restoration and will pay the extra money to avoid an "over-restored" appearance. These are sold singly only. Passenger side part...

The 1967 XR7 did not have rocker panel mouldings as did the 1968 - 1973 XR7 Cougars. All 1967 XR7 models came equipped with these "Hash" marks fastened to the rear of both rockers, at a rear tilting angle. Both sides received seven ribs, held by two Phillips screws each for a total of fourteen ribs in all. They were painted semi-gloss black in the recessed areas and the screws themselves were black as well. The leading ribs are usually pretty rough looking due to road debris wear, the one...

These always are peeling. Located on the right side on the dash face...

Good used emblem that is not warped and still has the silver paint intact. Don, Thought you might like to see another success story due to help from W.C.C.C. Attached is a picture of my 67 XR7, Lime Frost with Saddle interior. Thanks for all your help and advice. You and your team made a dream come true. Jim Kohler Check out this video

NOS "C" pillar emblem for your XR7. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Ford part number C7WY-6528818-B1

Good used "C" pillar emblem for your XR7 with no obvious pitting. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.Ford part number C7WY-6528818-B1 Hi Don: Thank you for fixing me up with the XR-7 pillar emblems. I appreciate doing business with you. It's nice doing business with guys who are not perfect, but try to be and correct anything within reason that is called to their attention. Take care, Greg Worth TN ...

Concours quality, perfect fit and a great value for the money. These little emblems are often the first thing one sees as they approach your car as they are at eye level. These emblems are located on the "C" pillars of your 67 - 68 Cougar but can also be used on a 71-76 Cougar with little or no modification. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Note that if you want to replace these emblems...

Poor chrome, for use as a core to be restored.

Assembly required This high quality corral fits perfectly and the chrome plating is well beyond what Ford originally did. The mounting studs are placed in the exact position as original. We have offered the walking cat and black background for sometime now but the challenge has been getting your used corral (or rectangle frame) remounted after you break off the studs to remove the assembly. Replacing this emblem assembly is probably (for the money) the best way to improve the looks of the...

Used core emblem that will need a new background decal. May have one or two hard to find small pits but will be above average even for a Western car. Make sure you consider our reproduction part before you purchase this. This used unit will be harder to install due to the fact that they were only designed to be installed once. Click on images to enlarge. The above is a very sought after collectible that was circulated back in 1967-1968. This picture above (From Jim Pinkerton) is of a pen...

New product that is in stock and ready for shipment now! Concours quality, perfect fit and a great value for the money. These little emblems are often the first thing one sees as they approach your car as they are at eye level. These emblems are located on the "C" pillars of your 67 - 68 Cougar but can also be used on a 71-76 Cougar with little or no modification. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C'...

Most of our grade A pads (other than black) will show some degree of fading. If you plan on repainting let us know and instead of replacing the reproduction emblem and beauty ring we will leave them off the pad for you to install after painting. Used grade "A" horn center / pad in aqua for the Mercury Cougar. Keep in mind that Aqua and Light Blue are very similar in color, once Aqua starts to fade, it becomes Light Blue. This is the best used example of a 1967 horn center / pad. Rarely do...

Most of our grade A pads (other than black) will show some degree of fading. If you plan on repainting let us know and instead of replacing the reproduction emblem and beauty ring we will leave them off the pad for you to install after painting. Used grade "A" horn center / pad in black for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock, so we'll do what we can to get a good pad for you. This...

Most of our grade A pads (other than black) will show some degree of fading. If you plan on repainting let us know and instead of replacing the reproduction emblem and beauty ring we will leave them off the pad for you to install after painting. Used grade "A" horn center / pad in light ivy gold / light green for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you...

Most of our grade A pads (other than black) will show some degree of fading. If you plan on repainting let us know and instead of replacing the reproduction emblem and beauty ring we will leave them off the pad for you to install after painting. Used grade "A" horn center / pad in parchment / off-white for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good...

Most of our grade A pads (other than black) will show some degree of fading. If you plan on repainting let us know and instead of replacing the reproduction emblem and beauty ring we will leave them off the pad for you to install after painting. Used grade "A" horn center / pad in red for the Mercury Cougar. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer...

Most of our grade A pads (other than black) will show some degree of fading. If you plan on repainting let us know and instead of replacing the reproduction emblem and beauty ring we will leave them off the pad for you to install after painting. Used grade "A" horn center / pad in saddle for the Mercury cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit...

Used Grade "A" Grille Center Medallion for the 1967 and 1968 Mercury Cougar. These will not have pits or damage to the chrome. Unfortunately the softer black background insert will often times have marks. Ford part # C7WB-8B344-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

What a difference a few minor blemishes can make in price! Our grade "B" used centers will always have a few minor dings as shown and maybe some very minor pitting in the painted part but after some clean up they will look almost as good as our grade "A" units when viewed from several feet away. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

Rechromed Grille Center Medallion for the 1967 and 1968 Mercury Cougar. Unfortunately the polishing and plating process will take away much of the detail. Cores must be pit free or very close to. Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If...

Used aluminum "Mercury Man" head for the center grille medallion. These are just pressed and swedged into the die cast bezel and come out easily with a light tap from behind. Keep in mind these highly amplified pictures make the emblem look much worse than it really is. Do know that the one you get will have light road debris wear but no major scratches, pits or scrapes. You will also want to replace the background foil decal when you purchase this emblem. Part of Ford assembly C7WY-8A223-A ...

New product that is in stock and ready to ship! Unlike 1968 the 1967 xr7 console indicator light bar had no woodgrain applique. This will work fine on your 68 and some prefer the 1967 look over the 1968 version. We have a few of these with a 1968 Burl Wood Overlay applied to them. If you would like one of these, mention it in the order notes and if we have any remaining will send you one of these. These two pictures give you an idea what the lights will look like when illuminated. When not lit...

Correct original windshield washer reservoir cap with "Mercury Man" logo. All the replacements are plain as was the Ford products that used this same cap configuration. Ford part number C7AZ-17632-A

Brand new WCCC exclusive! These 1967-only steering wheel center emblems have been needed for some time. Most originals are faded, scratched, and often warped or broken. These new ones fit perfectly in your original center pad and look great. Our video below shows how to replace the trim ring, along with this center emblem

Used cover with dull chrome. This used to be a very sought after and expensive part due to how difficult they were to find. Now that our show quality reproductions are here they have little value... Great for someone that just wants their driver to look complete. Fits all 1967-68 Mercury Cougars, Standard and XR7 models. Decal inserts available separately. Check out this video