Convertible

C5AZ-7630702-A Ashtray receptacle for 1969-70 Mercury Cougar and Ford Mustang. Only the rear door panel ashtrays in the back seat area. Receptacle only, sliding covered retainer sold separately. Also fits 1965-68 Ford and Mercury full sized convertibles. Decades old gum stuck to the bottom is no extra charge...

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

Keeper or retainer for attaching the convertible top cylinder pins. These are usually broken when replacing convertible top cylinders. One retainer per side.Ford Part # 372552-S These are not a exact replica of the t-bolt retainer, but will work for a replacement for the retainer on the T-bolt on the door windows (T-bolt Ford Part # C8SZ-6523274-A).  Ford part number for the retainer is C7SZ-65234A28-A.

Metal strip that fastens the weatherstrip to the bottom side of the header bow.

This is the stainless steel retainer trim for the front of the boot that attaches to the upper back side of the back seat in a convertible 1969 or 1970 Cougar, Shelby or Mustang. This is a grade B part with a small ding or imperfection. Ford part number: C9ZZ-7654676-A Click on images to enlarge. ...

Good used platform that is unique to the convertible. This will have a couple of thin spots but will be functional as is with all four mounting areas in good condition. This part is rarely in stock due to the lack of convertible parts cars with usable floor parts.

Good used platform that is unique to the convertible. This will have a couple of thin spots but will be functional as is with all four mounting areas in good condition. This part is rarely in stock due to the lack of convertible parts cars with usable floor parts.

No damage original bolt. Sold individually, two required per car.

Slat or pivot bracket for attaching the #4 rear most bow on a 1969-70 convertible top. Sold individually, one for each side needed for installation. Bushing is normally broken or missing, plan on sourcing or making a replacement bushing for the pivot. Ford part number C9ZZ-7650340-A.

This is the exact same cut of sound deadener as the tar based sound deadener, but cut out of the foil heat shield rather than the paper backed tar. The foil heat shield weighs over 20 Lbs less than the paper backed tar when cut into the same pattern. This makes shipping this over seas much more affordable than the paper backed tar version of the underlayment kit.For a super cheap version of this insulation, try this item: foil insulation ...

This is the 1968 Cougar visor bracket. Not an exact match for 1971 - 1973, but will work. The hole spacing and distance from the windshield is identical to that on the 71-73, the bracket is just 1/8" longer on the side that actually holds the visor tip. This unit is only available in black or neutral. We have most other unfaded colors in used. This item works for 68 Cougar Coupe, 68 Mustang Coupe / Convertible and 71-73 Cougar Convertibles. Replaces Ford Part # C8ZZ-6204132, C8ZZ-17690 OR...

Excellent quality reproduction sun visor assemblies and corner trim for the convertible 1969 - 1970 Mercury Cougar or Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. Sold as a pair, the original passenger side part has a C9ZB-7604122-C casting number on the back side and the driver side reads C9ZB-7604123-C. These will also interchange with versions ending in A B or D. Later versions will show one less screw tab. Replaces Ford part # C9ZZ-7604144 /...

Excellent quality reproduction sun visor assembly for the convertible 1971-73 Mercury Cougar and Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. The original casting numbers as seen on the back side will read D1ZB-7604123-AE for the driver side and D1ZB-7604122-AE for the passenger side. Sold as a pair.Replaces Ford part numbers D1ZZ-7604144-A, D1ZZ-7604145-A, and D2ZZ-7604144-A, D2ZZ-7604145-A.

Grade B used convertible sun visor bracket assembly for the driver side of any 1969-70 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results.  These will almost always, show some wear in the pocket, where the hook attaches.Ford casting number C9ZB-7604123.

Grade B used convertible sun visor bracket assembly for the driver side of any 1971-73 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results. Two casting numbers found between 1971 and 1973. We won't always have both numbers in stock but from the front side they are the same. Can be either D1ZB-7604123-AE or D2ZB-7604123-AA.  These will almost always, show some wear in the pocket, where the hook...

Grade B used convertible sun visor bracket assembly for the passenger side of any 1969-70 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results.  These will almost always, show some wear in the pocket, where the hook attaches.Ford casting number C9ZB-7604122.

Grade B used convertible sun visor bracket assembly for the passenger side of any 1971-73 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results. Two casting numbers found between 1971 and 1973. We won't always have both numbers in stock but from the front side they are the same. Can be either D1ZB-7604122-AD or D2ZB-7604122-AA.  These will almost always show some wear, in the pocket where the hook...

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

Used 2 hole front mount center bracket for the sun visors for the Mercury Cougar and Ford Mustang convertibles.  Contrary to what the aftermarket says, these are slightly different from the 1968 'C8ZB-6504132' sun visor bracket. These colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your color in the 'comments section' of your order. We have these in a limited supply. Ford...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction one year only switch for the 1968 Mercury Cougar with power sunroof (or 1968 Ford Mustang convertible). The XR7 G used a different switch built into the console but the other Cougars ordered with a sunroof in 1968 had this switch mounted to the right of the steering column under the dash.   Knob and bracket included as shown.

This listing is for a modified reproduction power window switch, made to work as a convertible top switch, with a good used original center dash toggle button. NOTE: you will need to modify your wiring for this to work - see instructions below. For years 1970 XR-7 convertible owners have been calling us asking for this switch with a "I am sure you probably do not have this but here it goes..." type of request. A customer of mine clued us into this "go-around" trick and we have since...

This listing is for a used power window switch, tested and in working condition. This is the stock wiring configuration. Open the plastic holder by moving these small clips aside... ...and this is what you'll see on the inside. Rearrange the wires so that they look like this: Note: You may need to bend the wires to seat properly in the new position. Next, carefully close the lid, making sure the connectors are properly aligned in the holes. This is what it looks like when you're finished: You...

Convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Very nice reproduction item, comes as shown with the knob marked "TOP". *Note - The 1970 Mercury Cougar XR7 had the power top switch located in the convenience switch panel in the dash.

Used convertible top switch for any 1971-73 Mercury Cougar Standard Model Convertible - Non-XR7. This is a momentary push switch. Tested and and working used switch.Replaces Ford part number D1WY-15668-A.

Used convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Used and tested convertible top switch, it will not come with a knob, sold separately. This switch was also used on Cougars with factory power sunroofs. *Note - The 1970 Mercury Cougar XR7 had the power top switch located in the convenience switch panel in the dash. ...

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...

A quality rust proof stainless steel cable which features all the correct hardware. Sold as a pair. Replaces Ford Part #: C9ZZ-7652806-A.

Reproduction tips and screws for your convertible top welt. It's the strip that goes across the top back side of the convertible top. These are the decorative tips that go on each end of the welt.Each kit includes two tips and two screws.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

*NOTE* 1969 - 1970 Convertible mats do not have any covering to the right of the gas tank. This is in fact how the originals were made. Many Convertible owners prefer to have a full cover mat. If that is you we suggest you purchase the coupe mat for your convertible.This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern. Do NOT confuse this with the light duty mat you will see...

This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray speckled pattern for 1971 - 1973. Do NOT confuse this with the light duty mat you will see elsewhere listed for the same money or less. The budget mats you see elsewhere weigh only a few ounces and flail around inside your trunk every time you close the lid! The pattern will not smudge or wear off easily and it will lay flat and fit perfect the...

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654606-A and are marked R.H. for the passenger side.

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Metal portion of the driver side rear interior panel on a 1969-70 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Grade A used, no obvious dents or rust.Basic Ford part number is 7631005. 

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Metal portion of the driver side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at least...

Metal portion of the passenger side rear interior panel on a 1969-70 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Grade A used, no obvious dents or rust. Basic Ford part number is 7631004.  *Note - Excludes Late 1970 with larger power window bezels.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Metal portion of the passenger side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at...

Replaces Ford Part # : D1ZZ-7651325-A

Replaces Ford part #: D1ZZ-7653986. Seven piece kit with attaching hardware.

This kit is easier to install than you may think! Five piece kit, comes with installation instructions. Be aware, the seals at the top of the glass do not line up perfectly leaving a gap on the quarter glass top seal. We are working on a solution.  Replaces Ford part # C9ZZ-7653986. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! Check out this...