1967 Ford Mustang

Used 14x5-1/2" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1969. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard. These 5-1/2 inch wheel will fit over stock disc brake calipers 1968-73. This 5-1/2 inch wheel is...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1970. Produced by Motor Wheels, early ones had riveted centers, changed to welded centers in 1969. Specify in the notes section if you have a preference, we seem to have mostly welded ones at the moment. Have a bent or damaged wheel? Don't...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. This were offered in 1967 with S code 390-4V option. Hard to find the 1967 manufactured version, we generally have the 1968-70 wheels, but they have a different center section. Have a bent or damaged wheel? Don't have a spare? These wheels will fit over front disc brakes....

NOS Standard seat belt retractor including bolts and a huge 44" x 33 1/2" Ford seat belt diagram in FoMoCo box and never installed on a car. Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models.  NOTE: Front retractors are same for left and right. Check out our video "All about...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is my absolute favorite Cougar - Mustang - Shelby option of all time! In fact, as a rather tall person that is not as slim as I once was, I do not really enjoy driving a Mustang or Cougar that does not have this option. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

Used strap or support bracket for the foam air conditioning vent tube going to the passenger side A/C vent. The electrical assembly manual indicates that two of these strap brackets were installed above inside the dash above the glove box. Our findings from the wrecking yard show that zero or one may have been installed. We have found a single bracket, no doubles, if at all. This part will seldom be in stock, but is fairly easy to fabricate. Find some 1/2 inch wide thin steel and cut a piece...

Radio support bracket for 1967-68 Mercury Cougar and Ford Mustangs without consoles. Used on AM, AM/FM, and AM/8Track factory radios.Replaces parts #s C7ZA-18888-A & C8ZA-18888-A, as found in the electrical assembly manuals.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Comes with all hardware pictured.

C7ZZ-5482-B This is a factory used front sway bar. This is the same size 3/4 inch diameter as the 289 and 302 sway bar but has a slight difference in the bends for the 1967 390-4V or 6.5Liter engines. This bar was factory identified with a One-Yellow and One-Blue paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573. *Note - 3 speed switches are different than the manual 3 speed switches.

C7ZZ-15520-USED Backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Ford part number C7ZZ-15520-A. *Note - 4 speed switches are different than the 3 speed switches.

Motorcraft new old stock brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a service replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. C7ZB-13480-B Replaces Ford Part #: C9VY-13480-A.

NOS brake warning light switch for the Mercury Cougar or Ford Mustang that is identified by the single pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder, this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Ford part # C7AZ-2B264-A.

Used brake warning light switch for the Mercury Cougar or Ford Mustang that is identified by the single pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder, this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems.Ford part # C7AZ-2B264-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

New Old Stock If you have an early 67 the plug may be the dual type which is also listed on this site. This will work with your C-4 or C-6 automatic transmission. Replaces Ford Part #: C9ZZ-7A247-B, SW 877 

Pull on switch assembly for the speed control option on probably the early system. Switch only, no knob. Ford part numbers C7WY-9A837-A and C7WA-9A837-A *Note – for use with factory cruise control.

NOS fixed column turn signal switch for the 1967 Mercury Cougar or Ford Mustang. This is a later service replacement turn signal switch, it may have an extra wire or two, and the wire lengths may be longer than the factory original. Ford part number C7ZZ-13341-F Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....

NOS switch and bracket for the emergency / parking brake. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part. Check out this video

Temperature thermostat for use in very early 1967 cars with 390 engines.  2-1/2 inches in diameter, 195°degree opening like OEM Ford. This is a Stant brand of thermostat. Note, this is a larger diameter thermostat than the common one used on a small block and most Ford engines. Only used with the intake and thermostat housing with large size diameter of 2-1/2 inches.

Used aluminum water neck of thermostat housing for EARLY 1967 Mercury Cougar or most other 1965-66 Fords with 390 / 428 engines. Cast aluminum finish. For use with early style 2-1/2 inch thermostats. Correct for early 1967 FE engines before about 11/1/1966. Not going to lie, these will show some signs of electrolysis on the inside and where the hose slips on. No thermal switch provision. Ford part with the C5AE-8594-A casting number.  *Note - mid and late 1967 cars used the...

Neat detail item, stamped steel with zinc plating. Mounts on intake manifold and holds one end of the accelerator linkage spring for the 289 / 302.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12-31/32 inches long. 1967 Mercury Cougar and Ford Mustang with S code 390-4V engines. Hooked end goes into the carburetor linkage, threaded end to the rear. Ford part number C7ZZ-9A702-A. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – not for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12-31/32 inches long. Application 1967 Mercury Cougar and Ford Mustang with 390-4V and cruise or speed control. Ford part number C7ZZ-9A702-D. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – for use with factory cruise control.

This is an upgraded version from what you see in our video but the idea is the same. This tool has a square hole so you can use your 3/8" drive ratchet or breaker bar to get the correct angle and have even better control of your leverage when placing the torsion bar into the slot. Used to remove the hinge springs (torsion rods) off the 1967 - 1973 Cougar or Mustang. No more trying to remove with the wrong tools . These can be tricky to remove without this tool.  Will not work on 1964 -...

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!

This item requires your core to be sent in advance, your core will be rebuilt. Rebuilt small block C6 Ford transmission torque converter for 351CJ in the 1972-73 Mercury Cougar and Ford and Mustang. 31 splines and 1.375" Pilot diameter. Fits small block C6 transmissions, typical for 351C engines and others when equipped with "U" code transmission and only Q code engines 1972-73. Only compatible with the very specific Q code flex plate. The torque converter bolt...

C-4 transmission 90 degree brass fitting for the rear oil cooler line. New reproduction with jamb nut and "O"-ring. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.

Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used Trunnion for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Trunnion is the white plastic bone looking thing with a hole in it. Attaches the Link and Rod from Servo Bell Crank. Ford part number C7ZZ-9D766-A.

Cancelling cam for the 67-69 Cougars and Mustangs with fixed columns. This cam is what returns your turn signal switch to the off position. This is not the same cam which comes inside tilt columns.

This is a stock photo, the actual lever we have will most likely be worn and will not be as nice as the one pictured. Grade A speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we may price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G This icon means that we're looking to buy...

Grade B speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G

NOS Speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln.  The 1968 Electrical manual shows a Lincoln part number of C7VA-9D752-G. Service replacement part number is D1VY-13305A. Would need to remove the white tilt bale collar prior to use.

One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

This connects the vacuum release valve to the vacuum system*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 3 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster. Bob Mannel's book indicates that this vacuum fitting was for A/C and Thermactor smog. Replaces generic Ford vacuum fitting part number 9A474.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used vacuum reservoir for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This is a 1967 only design that is very hard to find in rust free condition with a working vacuum check valve. Beware of substitutes as there are close facsimiles with different sized nipples, different brackets or plastic built in check valves. These versions off later model cars...

This unit mounts on the main air chamber, it opens and closes the air vent. NOS or new old stock.  This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Tested and working, Ford box.Replaces Ford part # C6OZ-18C311-A. ...

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

Vacuum tested working hot water valve for Mercury Cougars and Ford Mustangs equipped with factory A/C. This valve stops the flow of warm coolant when the A/C is on and has the original cast brass valve with bracket and vacuum pod. We are unable to guarantee that the water seal is good. Ford part # C7ZZ-18495-A, casting number on vacuum valve C7ZA-18C310-A.

Core C-4 Transmission valve body for any 1967-68 Mercury Cougar or 1967-69 Ford Mustang with code "W" transmission code on the door tag. This is only for 1967 through 1969 transmissions with P-R-N-D-2-1 shift pattern. Also known as the 8 bolt valve body. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in...