1967 Ford Mustang

C7ZZ-6521772-A Bracket that mounts to the door window channel, it prevents the rear section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and Ford Mustangs. Works on either the passenger or drivers side door. Casting # is C7ZB-21772-A See C7ZZ-222A54-A for the companion stop on the door guide.See C7ZZ-6521768-A for the front stop bracket and bolt.You can find the reproduction here.Check out our handy diagram below to find other '67-'68 door parts you...

CLEAR Glass without Shade; does not have Carlite logo, perfect fit. We also sell the Window weld for the installation. Fits 1967-68 Mercury Cougar and 1965-68 Ford Mustang coupe or hardtop only. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed. Keep in mind this is a common windshield that can be picked up...

Reproduction green tinted windshield that features a blue tinted band a crossed the top of the windshield. Not only will this unit look great, but it will fit perfectly as well. We also sell the bedding compound for the installation. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed. Keep in mind this is a common...

Defrost or defroster duct for the windshield on all 1967-68 Mercury Cougar and Ford Mustangs with factory A/C or air conditioning. This Grade A version will be free of all but very cosmetic defects. Meaning no broken tabs, or torn or missing screens. Replaces Ford part numbers C7ZA-18490-E and C8ZA-18490-B.*Note - Only fits those cars with factory or integral air conditioning. Cars with heaters only used two individual nozzles.

Defrost or defroster duct for the windshield on all 1967-68 Mercury Cougar and Ford Mustangs with factory A/C or air conditioning. This Grade B version may have one of the following: crack or chip, have a broken tab, or a torn or missing screen. B grades will install and work, they just may need a bit of duct tape or be held on with 3 of the 4 screws.Replaces Ford part numbers C7ZA-18490-E and C8ZA-18490-B.*Note - Only fits those cars with factory or integral air conditioning. Cars with...

Replacement bellows for your 67-68 windshield washer foot pedal pump. Over the years

Good used windshield washer pump rubber hose assembly

Economy version of the 67 - 68 washer bottle that has the incorrect "stepped down" design on the nipple and no FoMoCo Insignia. Comes with plain cap but we also have good used caps with Mercury Man logo which is correct for the Cougar here.You can find the washer bottle with the correct FoMoCo logo here.Replaces Ford part # C7OZ-17618-A. ...

Premium version of the 67 - 68 washer bottle that has the FoMoCo Insignia and correct style nipple. Comes with plain cap but we also have good used caps with Mercury Man logo which is correct for the Cougar here.Replaces Ford part # C7OZ-17618-A.

This is the bracket on which the windshield washer bag hang on the 1967 Mercury Cougar.  According to Phil Parcells

These zinc-plated Washer Nozzles are exact copies of the originals. Sold in pairs.Replaces Ford Part #: C7ZZ-17603-A.

Injection molded high strength plastic connector for hoses leading to nozzles. Factory fit.Replaces Ford Part #: C7SZ-17A601-A or C0AB-17A601-A.Will not fit 69-70 with factory hoses as they used Ford part # C8OZ-17A601-A

Satin Finish Wiper Arm

These are hand picked grade A condition original arms with no defects. Right is the same as left. Sold individually, two per car. The reproductions of the 67 - 70 are identical, but the originals are NOT! The 67 - 68 and the 69 - 70 were bent at different angles and carry different Trico patent numbers. In our experience in owning and parting 100's of early Cougars, 1967 and 1968 use the early style, and 1969 and 70 use the later style. Click here to see pics of the differences between the 67...

Exact reproduction of original. Original manufacturer has redesigned blade assembly with plastic components. Sold individually

Original stainless steel wiper assembly, fits any 1967-68 Mercury Cougar or Ford Mustang. Has the original metal fastener to connect to your wiper arm, rather than the plastic piece used in the reproductions. Sold individually, two per car, 15" rubber wiper blade not included.Replaces Ford part #: C3AZ-17528-J.

Original FoMoCo used two speed windshield wiper motor for your 1967-68 Mercury Cougar or Ford Mustang. This used motor comes as shown with wiring harness for all 1967-68 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1967-68 installation, must be marked 7Z. Linkage arms sold separately. Stamped C7ZF-17504-D, Ford part # C6OZ-17508-D.

This Wiper Pivot To Cowl Seal Reproduction is sold as a pair. Fits both the 67 and 68. Replaces Ford part #: C5ZZ-17475.

A nice reproduction of the standard air cleaner wing nut. This version was used on most Ford products through the 1980's.

Reproduction wing nut for the snorkel on your air cleaner. Good for the 1967 Cougar or Mustang.

Correct spare tire hold down wing nut for the 1967 Mercury Cougar or Ford Mustang. Replaces Ford Part #: B9AZ-1462-A.

This is an exact reproduction of the wiper transmissions that will connect to the wiper motor and the output shafts. It includes correct links and pivots for full range of motion. This is commonly replaced when swapping your cowl panel

Used wiper transmissions that will connect to the wiper motor and the output shafts. This is commonly replaced when swapping your cowl panel, steel dash panel, and/or firewall. If you want to keep your car original, go with these good used arms, or you can find the reproductions here.

Reproduction Dash to Engine Gauge Feed Harness with the push-on post oil sender for the 1967 and 1968 Mercury Cougar or Mustang with the 390, 427 or 428 Big Block. Replaces Ford Part #: C7ZZ-14289-ACheck out the video below on our new gauge tester: ...

Anti rattle spring for the 1967 Cougar and Mustang clutch release lever spring. Ford part number C6AZ-7562-A.

Used wire extension for the tilt / tilt away steering column found in the Mercury Cougar or ford Mustang. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts needed. To offset the cost of your rebuild, you can send us additional parts or parts columns and we will give...

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.Replaces Ford Part #: C9ZB-19A885-B.

Reproduction console feed harness for the 67 - 68 Cougar or Mustang. This OEM direct fit wiring harness supplies power from the under dash harness to the console harness.

Complete 25 piece clip kit for the 1967 Cougar or Mustang. Keep in mind that this is produced as a Mustang clip kit, and although most clips are the same between Mustang and Cougar...not all clips apply to Cougar applications.   

This Screw fastens the plastic guide for turn signal wires next to column under the cone by steering wheel.

Used black plastic clip for holding the turn signal wiring harness to the column tube, next to the vacuum actuator. Fits any 1967 Mercury Cougar or Ford Mustang with tilt swing away steering columns.

Master clip kit which includes the following fasteners:Engine bayEngine feedFirewallFront crossmemberParking lightsPassenger side apron below relayRadio cable to dashKeep in mind that not all fasteners found on 1967 Courgars / Mustangs are in this kit.

Under dash wiring harness assembly for all 1967 Mercury Cougar and Ford Mustangs with integral, or factory installed air conditioning. All wiring harnesses are test and inspected by our electrical department.Replaces Ford part number C7ZB-19945-A.

New console wiring harness for 1967-68 Standard Cougar any all 1967-68 Ford Mustang. This harness is for the light in the roll up garage door compartment and the rear console lights. There is a jumper wiring harness also available, that connects to the main under dash harness. See related items. Ford part number C7ZB-13B711-A. *Note - Not for Mercury Cougar XR7 models.

Reproduction console wiring harness for 1967-68 Standard Cougar any all Mustang. This harness is for the light in the roll up garage door compartment and the rear console lights. There is a jumper wiring harness also available, that connects to the main under dash harness. See related items. Replaces Ford part number C7ZB-13B711-A. *Note - Not for Mercury Cougar XR7 models.

Console wiring harness for 1967-68 Standard Cougar any all Mustang. This harness is for the light in the roll up garage door compartment and the rear console lights. There is a jumper wiring harness also available, that connects to the main under dash harness. See related items. Ford part number C7ZB-13B711-A. *Note - Not for Mercury Cougar XR7 models.

Used radio light socket and wiring pigtail for all factory Philco AM radios as installed in 1967-70 Mercury Cougar and Ford Mustang cars. These light sockets are tested and cleaned, and have enough wiring lead to re-solder or crimp connect to your Philco AM radio. Original part with correct color wire.

Original used AM radio speaker lead wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustangs with factory AM radios. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios

Original used speaker lead wiring harness pigtail for all 67 - 68 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the kick panel.*Note - The only difference between this pigtail and the one listed for the 1969-70 dash speaker is the actual plug design.

Used under dash wiring harness repair plug and pigtail for the neutral safety switch / back-up lights and engine feed harness for the LATE 1967 Mercury Cougar. Works for both standard and XR7. This is part of the 14401 main under dash wiring harness.*NOTE* The blue/red to yellow/black wire is for the radio feed. The only difference between the early and late harnesses, is the early harness has an extra blue wire.

New wiring pigtail with male bullet connector, and male / female paired connector. Also has rubber grommet that fits a 5/8" inch hole. Looks like 18 gauge wiring. These are remnants from the reproduction Mustang front turn signal lights that we convert to Cougar wiring. Brand new, approximately 13-15 inches in total length. Colors as shown.

Original used AM radio power lead wiring harness pigtail for the 67 - 71 Mercury Cougar and Ford Mustangs with factory AM radios. This double male plugged wiring pigtail solders to the your factory Ford AM radio. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios.

Reproduction wiring harness pigtail plug for the 67 - 68 Cougar or Mustang voltage regulator.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...

Reproduction under hood wiring harness repair plugs and leads that go from the under hood harness to the starter solenoid on the Mercury Cougar or Ford Mustang.  Sold as a pair.

Used plug and wiring pigtail for the brake light warning switch located on the drum or disc brake distribution block mounted to the driver side fender apron. This is a plug and section of wire for repairing the underhood harness. Unique rubber sealed plug, 1967 single pin only. Violet colored wire. Fits 1967 Mercury Cougar and Ford Mustangs.

Correct plug for your 67-71 AM- FM radio, or 8-track... Often these have been cut from the main loom to install an after market radio.The 1972 model used the same plug, but the wires are not in the same spots, go figure! These are speaker wires not power wires.The color codes are:  White right cowl speaker.   Orange left cowl speaker. Speaker blue / black ground. Power "not this listing." Blue / red stripe, radio light. Yellow / black stripe, power in for radio. ...