1967 Ford Mustang

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used pin for the locking lever in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Two are required in 1967-69, but only one is required for 1970 and up. Recommend changing to a up dated version of this pin with one that has circlips or snap rings (15-0156 for 1967 -69 or 15-0157 for 1970-1973) *NOTE* For tilt column service, you can contact Tony...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Locking pawl catch pin for your 67-69 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break...

New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.

Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang. 

C3AZ-4730-B Rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1970 Mercury Cougar and Ford Mustangs. Good used part with solidly mounted metal threaded stud. Pinion bumper. The casting number seen on the 67-68 is C3AA-4906-C, this version has fine threads. The version most often seen on the 69-70 is C9OA-4906-A. It will have a coarse threaded mounting stud. Two of these were used on certain 1967 Shelby Mustangs with traction bars.

Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.

Reproduction Exhaust Manifold Pipe Stud Kit for the 260, 289, 302, 351 and 1969 390GT 1967 - 1972 Mercury Cougar and Ford Mustang

Kit has the longer studs for use with spacers or butterfly spacers, between 390 and 428CJ passenger side exhaust manifolds and H pipe flange.

Reproduction Pitman Arm w/ 1" Sector Shaft Nut EACH for the 1967 Mercury Cougar or Ford Mustang

1967 - 1970 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C7ZZ-3590-B. Note that early 67's will have a 1" sector shaft. Check out this video

C7ZA-3590-B 1967 - 1968 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C7ZZ-3590-B. Check out this video

Power steering pitman arm for any 67-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts.  Replaces Ford part number C9ZA-3590-A This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Check out this video

Power steering pitman arm for any 1967-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts. This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Check out this video

Quality reproduction of the early 1967 Pitman arm for use with the 1 inch sector shaft from the steering box. Power steering only. Check out this video

C4ZA-3590-A Early 1967 Steering box pitman arm with 1 inch sector shaft. Power steering only, used with SMB-E steering box. Fits early 1967 Mercury Cougar and 1965- early 1967 Ford Mustang. Ford part number C5ZZ-3590-A. Caution, measure your steering box sector shaft, many of the short boxes have been changed to the 1-1/8 inch boxes. Rare part, limited to stock on hand. Check out this video

C7ZA-3590-C 1967 - 1968 Power steering box pitman arm with 1-1/8" inch sector shaft. Ford part number C7ZZ-3590-C. Check out this video

Reproduction pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and 2 - 4 are required per car. Pin is custom made on short runs and is very difficult to find. .001 undersized, and with 8/32 threads instead of 6/32 like the originals. Newer pin removal tools will fit. Replaces Ford part # C7SZ-3D739-A. Removing pivot pins on 67 - 69 tilt away columns: Work on the upper knuckle pivot pins as there is room...

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1076 WHITE Led Plasma back up light bulb for your 67-68 or 71-73 Cougar, Mustang or anything else you might have that takes an 1076 bulb. Please note that these bulbs are ground sensitive. Specs: Power: 7.5 Watts Brightness: 300 Lumens Total life expectancy: 30,000 hours 2" Tall (1 3/8" extends out of the socket) Comparison image - Click to view full-size: Check...

1967-68 and 1971-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175 As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 and will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003 bulbs).  Basically good for every car from 1950 to 1990 that uses a 1156...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1157 WHITE LED Plasma stop lamp / turn signal light bulb for your 67 - 73 Cougar, Mustang or anything else you might have that takes a white 1157 bulb. Please note that these bulbs are ground sensitive. Did you know that white (clear) 1157 bulbs fit a ton of other cars and trailers from the 50's clear through the 90's and beyond that used the...

24" hose with metal coil (like original) instead of plastic coil found in most. Coils are wrapped in a 6+ mil plastic rather than the 3 mil plastic that you can easily put your thumb through. Does not come with clips. May require being cut to fit some applications. 2 required per car. Replaces Ford Part #: B5A-18556-C.Replaces Ford Part #: B5A-18556-C.

Used cover plate or thrust plate that retains the camshaft on the front of Ford small block V-8 engines such as 289, 302, 351W. 1967-70 Mercury Cougar or Ford anything. This plate has three bumps, we have found a Ford number of C9OZ-6269-A, this may be a service replacement number and could be found on engines built earlier than 1969. We have found this style of 289's from 1967. There is another version with Ford number C2OZ-6269-A, it only has two bumps.

Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A, 

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver and passenger side lower only, kind of shaped like the State of Utah. Fits driver and passenger side hinges. Fits any 1967 Mercury Cougar and Ford Mustang. Ford part number 6502667.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver and passenger side upper only. Fits any 1967 Mercury Cougar and Ford Mustang.Ford part number 6502666.

Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C5ZZ-6512118-A.

These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up. Plug size: 1 1/2"   also used for the electric headlight conversion kit for the firewall pass through body plug.  

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

This kit includes 33 pieces and has the quarter panel drain valves.

These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up.Plug Size 1 1/2"

Set of 4 seat mounting access floor pan plugs, enough for one seat. 2 kits needed for both bucket seats. This is a good idea to pick up two sets of these when replacing carpeting. These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up. Plug Size 1 1/2"

Reproduction master cylinder decal for the 1967 - 1969 Mercury Cougar or Ford Mustang. This decal was not used on later year cars. These types of decals are for the person to whom details matter.  Customer feedback found at mercurycougar.net:  Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are...

C8ZZ-3A713-A Return or low pressure hose. Low pressure hose from the control valve to insulator. 1968-70 Mercury Cougar Ford Mustang all V-8 engines. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. *Note - There are two halves to the low pressure hose from the control valve to the pump. This is the lower half only. Please see part number 42301 for the upper section that works with this hose.Click this link for more clarity on power steering...

Lower pressure hose. High pressure hose from insulator to the control valve. 1967 Mercury Cougar Ford Mustang with S code 390-4V V-8 engines. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. *Note - There are two halves to the pressure hose from the pump to the control valve. This is the upper half only. Please see part number 31890 for the lower section of pressure hose. Click this link for more clarity on power steering hoses: https://secure.cougarpa...

C7ZA-3A719-B Upper pressure hose. High pressure hose from the pump to insulator. 1967 Mercury Cougar Ford Mustang with S code 390-4V V-8 engines. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. *Note - There are two halves to the pressure hose from the pump to the control valve. This is the upper half only. Please see part number 31891 for the lower section of pressure hose. Click this link for more clarity on power steering hoses: https://secure.coug...

Pair of correct power steering hoses for your 67-69 Cougar or Mustang. All correct ribbing, striping, and crimping. Hoses have 5/16" fittings. *Note: Cannot be used with the very early 1967 1/4" fittings on control valves and ram cylinders. *Note - Two different hoses attach between the control valve and the ram cylinder. Part numbers: C60A-3A717-A C60A-3A714-A

C6OA-3A717-A pressure hose. Ram cylinder to control valve. All correct ribbing, striping, and crimping. Hose with 5/16 fittings used 1967-69 Mercury and Ford. *Note - Two different hoses attach between the control valve and the ram cylinder PS7U1B and PS4U1A. *Note can not be used with the very early 1967 1/4" fittings on control valves and ram cylinders.

C6OA-3A714-A pressure hose. Control valve to ram cylinder. All correct ribbing, striping, and crimping. Hose with 5/16 fittings used 1967-69 Mercury and Ford. *Note can not be used with the very early 1967 1/4" fittings on control valves and ram cylinders. *Note - Two different hoses attach between the control valve and the ram cylinder PS7U1B and PS4U1A.

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

Reproduction multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Does not include dipstick. Manufacurers note: In place of the paper gaskets, it is recommended that you use gray atv...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...