All Available Parts - 1969 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 601-700 of 3512
Sorted By:
Availability:
Display Options:
Availability: Used / Wrecking Yard Item
Item #: 11-0334 -
Shaft or rod for the evaporator damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft has a tab mounted on the lever, and is clocked differently than the 1969-73 version. The evaporator damper door allows air to pass over the evaporator in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related...
Availability: In-Stock Item
Item #: 41704 -
Concourse correct 3" long nipple that installs in the water pump, with the correct plating.C8OZ-18599-A.
Availability: In-Stock Item
Item #: 11-4003 -
Used mounting plate for the heater blower motor on the 69 - 70 Cougar or Mustang without A/C.Keep in mind that this same plate can be used on a 67 - 68 Cougar and Mustang heater blower motor with A/C.
Availability: Out of Stock
Item #: 11-0030 -
Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A
Availability: Used / Wrecking Yard Item
Item #: 11-0031 -
C9ZZ-18578-A mounts to the rear of the factory installed heater control ventilation control pane. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1969-73 selector button kit. LINK This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...
Availability: Used / Wrecking Yard Item
Item #: 11-0032 -
C9ZZ-18A651-A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic knobs and the lever borders. Knobs and light socket wiring harness not included. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A...
Availability: In-Stock Item
Item #: 26157 -
Concours correct red striped heater hose for all 1969 Mercury Cougars and Ford Mustangs WITHOUT air conditioning. Correct for use with all V-8 engines. Durable red striping with "Autolite" spelled out and dated H8H02A. Some length trimming may be required for a tight looking fit.
Availability: In-Stock Item
Item #: 26159 -
Concours correct red striped heater hose for 1969 Mercury Cougars and Ford Mustangs with factory or integral air conditioning. Durable red striping with "Autolite" spelled out and dated H8H02A. These hoses have a correctly molded 90 degree elbow on one end that fits on the water valve side. Some length trimming may be required for a tight looking fit.
Availability: Used / Wrecking Yard Item
Item #: 11-0051 -
C9ZA-18C433-C lower heater duct to floor outlet for Cougars and Mustangs without air conditioning. Used grade "A" part and may have one very minor defect. This part might have a small crack, but it will not have any broken or missing tabs. It's good, it's cheapish, you want it.
Availability: In-Stock Item
Item #: 12335 -
New clear plastic lens or face plate for the heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!
Availability: In-Stock Item
Item #: 13682 -
New clear plastic lens or face plate for the ultra rare Power Ventilation option, heater control with power vent on all 1969 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. The Power Ventilation option added a center vent to the dash as was found on factory air conditioning cars. Just more outside air circulation.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff...
Availability: In-Stock Item
Item #: 31119 -
This exact reproduction mounts to the rear of the factory installed heater control ventilation control panel. Save your knob or consider purchasing the 1969-73 selector button kit, find it here. Replaces Ford Part number C9ZZ-18578-A
Availability: Used / Wrecking Yard Item
Item #: 11-0444 -
Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). The pictures in the sequence above are reference pictures, grade B boxes will have cracks or breaks. Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Save your old fan motor and plate, this unit does not come with a fan assembly. Grade B used, will have a crack or chips in the fiberglass. Fair condition, will need a...
Availability: Used / Wrecking Yard Item
Item #: 11-0145 -
Used driver side rear quarter window glass bracket, used for all 1969 and most of 1970. The later 1970 bracket had a D0Z... part number and used a different clip for attaching the window regulator. Good used bracket with all three plastic guides in perfect condition. This bracket is correct for Coupe and Convertible. Engineering # C9ZB-6529945-A Here is the 3M product used to glue the glass to the bracket. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install...
Availability: Out of Stock
Item #: 14208 -
Decent reproductions, but we suggest you consider our good used original FORD units that have been closely inspected for half the price! Replaces Ford part # C9ZZ-6530306-A. *NOTE* Originals were painted semi gloss black. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...
Availability: Out of Stock
Item #: 14170 -
Decent reproductions, but we suggest you consider our good used original FORD units that have been closely inspected for half the price. Replaces Ford Part #: C9ZZ-6530307-A. *NOTE* Originals were painted semi gloss black. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...
Availability: Used / Wrecking Yard Item
Item #: 20615 -
1969 Mercury Cougar and Ford Mustang convertible clear glass for the driver side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. *NOTE* Vertical chrome trim not include. Air conditioning cars were supposed...
Availability: Used / Wrecking Yard Item
Item #: 20618 -
1969 Mercury Cougar and Ford Mustang convertible clear glass for the passenger side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. *NOTE* Vertical chrome trim not include. Air conditioning cars were...
Availability: Used / Wrecking Yard Item
Item #: 15431 -
1969 Mercury Cougar and Ford Mustang convertible Grade B clear glass for the driver side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss, Shelby and Cougar Ford part number...
Availability: Used / Wrecking Yard Item
Item #: 15427 -
1969 Mercury Cougar and Ford Mustang convertible Grade B clear glass for the passenger side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part number C9ZZ-7629700-A. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear corner. Excludes...
Availability: Ships Direct from Supplier (Except International)
Item #: 15454 -
Excellent reproduction clear passenger side (right hand) glass for your 1969 Mercury Cougar convertible. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In...
Availability: Used / Wrecking Yard Item
Item #: 11-0147 -
Used passenger side rear quarter window glass bracket, used for all 1969 and most of 1970. The later 1970 bracket had a D0Z... part number and used a different clip for attaching the window regulator. Good used bracket with all three plastic guides in perfect condition. This bracket is correct for Coupe and Convertible. Engineering # C9ZB-6529944-A. Here is the 3M product used to glue the glass to the bracket. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly...
Availability: Used / Wrecking Yard Item
Item #: 15428 -
1969 Mercury Cougar and Ford Mustang convertible Grade B factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part number C9ZZ-7629700-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear corner. This unit will not fit...
Availability: Used / Wrecking Yard Item
Item #: 15432 -
1969 Mercury Cougar and Ford Mustang convertible Grade B factory tinted glass for the driver side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # C9ZZ-7629701-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear corner. Excludes coupes. Do you have...
Availability: Ships Direct from Supplier (Except International)
Item #: 15455 -
Reproduction passenger side (right hand) green tinted quarter window glass for the 1969 Mercury Cougar. This tint was called "Sun-X" tint and was an option on Cougars of this era. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is...
Availability: Used / Wrecking Yard Item
Item #: 11143 -
1969 Mercury Cougar and Ford Mustang convertible factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Vertical chrome trim not include. *NOTE* Air conditioning cars were supposed to have...
Availability: Used / Wrecking Yard Item
Item #: 11144 -
1969 Mercury Cougar and Ford Mustang convertible factory tinted glass for the driver side rear seating area, it will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Vertical chrome trim not include. *NOTE* Air conditioning cars were supposed to have...
Availability: In-Stock Item
Item #: 16192 -
Non-original style replacement clip for mounting the quarter window regulator arm to the window channel bracket on all 1969-70 Cougar and Mustang coupe and convertibles. This clip will work with either the 1969-early 1970 bracket and the late 1970 bracket. The late 1970 brackets used a unique spring steel clip that seldom is reusable. Sold individually, one each per window.
Availability: Used / Wrecking Yard Item
Item #: 11-0140 -
Used lower quarter window bracket for any 1969-70 Mercury Cougar and Ford Mustang non-fastback. This is the lower bracket that mounts to the bottom of the stationary slider bracket. This bracket adjusts the top movement in and out of the rear seat glass. Power or manual crank
Availability: Used / Wrecking Yard Item
Item #: 11-0153 -
Used driver side (left hand) quarter window regulator for the Mercury Cougar or Ford Mustang equipped with manually operated quarter windows. Nothing beats or fits like original FoMoCo! Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...
Availability: Used / Wrecking Yard Item
Item #: 11-0154 -
Used passenger side (right hand) quarter window regulator for the Mercury Cougar or Ford Mustang equipped with manually operated quarter windows. Nothing beats original FoMoCo! Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...
Availability: Out of Stock
Item #: 11-0285 -
Used roller for any 1969-70 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Often times one of the little branches breaks off and allows chattering of the window movement. Included is a good roller and drilled out rivet. These can be reused if you drill out the center of the rivet and using a tap
Availability: Used / Wrecking Yard Item
Item #: 11-0307 -
Used air conditioning thermostat switch for any 69-70 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash
Availability: Used / Wrecking Yard Item
Item #: 11-0377 -
Good used driver side (left hand) quarter window guide for the Mercury Cougar or Ford Mustang. This unit will ship as shown. Two different versions of these brackets are known. Difference is the position of the lower stop bracket the size and rubber bumper. All brackets come with rubber bumpers installed. We may substitute a new bumper for a missing bumper. We recommend a thorough cleaning and a liberal amount of Sil-Glyde grease or equivalent during re-assembly. Ford part # C9ZZ-6529753-A. Do...
Availability: Used / Wrecking Yard Item
Item #: 11-0378 -
Good used passenger side (right hand) quarter window guide for the 1969 -70 Mercury Cougar or Ford Mustang. Ford part # C9ZZ-6529752-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video
Availability: Used / Wrecking Yard Item
Item #: 11-0389 -
Passenger side quarter window rear stop bracket. Mounts behind the rear interior panel.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Passenger side only, C9 and D0 part numbers are fully interchangeable. Includes bolt as shown. Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang.Casting # is C9ZB-29968-A or D0ZB-29968-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0388 -
Driver side quarter window rear stop bracket. Mounts behind the rear interior panel.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Driver side only, C9 and D0 part numbers are fully interchangeable. Includes bolt as shown. Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang.NOTE: If you prefer one of the casting numbers below, please mention it in the notes section of your order.Casting # is C9ZB-29969-A or D0ZB-29969-A. ...
Availability: Used / Wrecking Yard Item
Item #: 11-0390 -
Driver side quarter window front stop bracket. Mounts in the door jamb of the quarter panel. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Driver and passenger side are the same, C9 and D0 part numbers are fully interchangeable. Includes bolts and plate as shown. Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang.Casting # is C9ZB-6530600-A or D0ZB-6530600-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0391 -
Passenger side quarter window extension bracket. Mounts in the door jamb, and holds the adjustment screw for the window guide.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Passenger side only. Includes bolts as shown, adjusting screw sold separately Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang. Manufactured by FabCo for Ford.Casting # is C9ZZ-6530056-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0392 -
Driver side quarter window extension bracket. Mounts in the door jamb, and holds the adjustment screw for the window guide.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Driver side only. Includes bolts as shown, adjusting screw sold separately Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang. Manufactured by FabCo for Ford.Casting # is C9ZZ-6530057-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0393 -
Quarter window upper adjusting screw and nut - used. Mounts to the extension assembly bracket. For all 1969-70 Mercury Cougars and Ford Mustangs. Includes bolt and nut as shown. Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang.Ford number is 381742-S2 and 376762-S2 for nut.
Availability: In-Stock Item
Item #: 32947 -
Individual screw for attaching the headlight retaining ring on any 1967-70 Mercury Cougar or 1965-70 Ford Mustang, and pretty much most all other Fords during those years. #8 stainless steel screw. Two needed per headlight bulb retaining ring. A total of 8 would be needed for a quad headlight system on all Cougars.Replaces Ford part number 375452-S.
Availability: In-Stock Item
Item #: 32395 -
New slotted pan head screw for mounting distributor points or condensers. Three total, per single advance Ford distributors. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x9/32". Sold individually, but you likely need 3.
Availability: In-Stock Item
Item #: 32396 -
New phosphate dipped slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". Sold individually, you will need 2.
Availability: In-Stock Item
Item #: 32371 -
Reproduction carburetor stud for all Ford numbered Holley carburetors 1967-71. 1/4-20 double ended stud from AMK. Stud only, no wingnut.
Availability: Out of Stock
Item #: 32996 -
Reproduction vacuum fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All brass fitting, goes into the passenger side of the carburetor for the vacuum advance. This should be ported vacuum.Ford part number 358165-S.
Availability: In-Stock Item
Item #: 32283 -
Brass screw in plug for select Autolite distributor vacuum advance units from 1968-71, typically the banded single advance units factory installed. Solid brass, originals were not, we believe that they were cadmium plated. Solid plug, should be hollow, with a 3/4 inch hex head. Works as it should. Fits most all vacuum advance that have a plug in the end as shown. *Note, when removing the old plug, there is a spring and washer inside.
Availability: Rare / NOS Part
Item #: 32303 -
Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS service replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.
Availability: In-Stock Item
Item #: 32391 -
Bolt kit for installing the idler and adjusting pulley on any 1968-70 Mercury Cougar / 1968-70 Ford Mustang or 1968-70 Ford / Mercury with 390, 428CJ engines. 4 bolts 3/8-16x7/8 inch washer head bolts and 2 thick 3/8 washers.
Availability: In-Stock Item
Item #: 32389 -
3/8-16x7/8 Bolt for installation of idler, adjusting pulleys, and brackets, on most 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, up to 8-9 are typically used per car. 9/16" hex, washer head bolt.
Availability: In-Stock Item
Item #: 32390 -
3/8 washer for installation of idler, adjusting pulleys, and brackets, on some 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, 1-2 are typically used per car.
Availability: Out of Stock
Item #: 33251 -
Grade A used deluxe shifter handle in black. Nice used condition may have a hairline crack in the plastic on the bottom. No release button or set screw included. See related items for Grade B Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...
Availability: Used / Wrecking Yard Item
Item #: 33252 -
Grade B used deluxe shifter handle various colors. Please specify color in the notes, limited to stock on hand. Fair used condition will have at least one crack in the plastic. May also have slightly pitted chrome. No release button or set screw included. See related items for Grade A Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 32407 -
Assembly line used engine lift hook. Driver side 1969-70 with 428 Cobra Jet engines, including 428SCJ. Stamped with number C8OE-17K004-B, which is the second version. An earlier version was used on 1968 R code cars. Fits all 1969-70 Ford cars with either R code or Q code 428 engines. Cougar, Mustang, Cyclone, Torino, Talledega, Cobra, Fairlane, Montego, Ranchero etc. Attaches to the driver side exhaust manifold. There is also a passenger side engine lift hook, see related items. ...
Availability: In-Stock Item
Item #: 33004 -
Reproduction idle mixture screw caps for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All white plastic caps. These were the tamper proof type of caps as installed from the factory.
Availability: In-Stock Item
Item #: 32578 -
5/32 Allen wrench. We offer this Allen wrench to go along with our dash bezel removal tools. This handy dandy 5/32 Allen wrench is needed to attach the ignition bezel tool to any of the 1967-69 Mercury Cougar or Ford Mustang ignition switch bezels.
Availability: In-Stock Item
Item #: 32169 -
AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to top loader transmission on all 1967-69 Mercury Cougar and Ford Mustang with 390 or 428CJ engines. AMK number F-1741.
Availability: In-Stock Item
Item #: 32170 -
AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to top loader transmission on all 1967-69 Mercury Cougar and Ford Mustang with 289, 302, 351W, and 351c engines. AMK number F-1414.
Availability: In-Stock Item
Item #: 32171 -
AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to any automatic transmission on all 1967-69 Mercury Cougar and Ford Mustang with 289, 302, 351W, 351C, 390, 428CJ engines. AMK number F-176.
Availability: In-Stock Item
Item #: 33183 -
Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.
Availability: Used / Wrecking Yard Item
Item #: 11-0107 -
Lower heater duct to floor outlet for Cougars or Mustangs with air conditioning. Used grade "B" part that will have minor defects. It will have cracks or chips. Almost half the price of the grade "A" piece and works awesome if you don't have one at all. Want to have directed heating, we've got you covered. Replaces Ford part number C9ZA-18C366-A.
Availability: In-Stock Item
Item #: 16140 -
Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.
Availability: In-Stock Item
Item #: 30386 -
Hex bolt for attaching fuel line clips. 5/16-18 bolt. See related items for reproduction clips.
Availability: In-Stock Item
Item #: 32998 -
This correctly formed carburetor throttle solenoid idle bracket for the 1970 428CJ engines on any Mercury Cougar or Ford Mustang. This is a nice reproduction item.Replaces part # D0ZZ-9B550-A.
Availability: In-Stock Item
Item #: 32177 -
AMK fastener kit for attaching manual transmission clutch Z-bar brackets. 1969-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines. AMK number F-473.
Availability: In-Stock Item
Item #: 32178 -
AMK fastener kit for attaching manual transmission clutch Z-bar brackets. 1969-70 Mercury Cougar and Ford Mustang with 302 or 351 engines. AMK number F-474.
Availability: Used / Wrecking Yard Item
Item #: 32608 -
Internal tail shaft assembly from a FMX transmission. We only disassemble up to what you see in the picture. *Excludes some FMX transmissions with 351C-4v in 1970. We do not have the larger diameter version available.
Availability: Used / Wrecking Yard Item
Item #: 32610 -
Internal tail shaft assembly from a C-6 transmission. We only disassemble up to what you see in the picture.
Availability: Used / Wrecking Yard Item
Item #: 32609 -
Internal tail shaft assembly from a C4 transmission. We only disassemble up to what you see in the picture. *Excludes later versions of C4 transmission that have thicker output shafts.
Availability: Used / Wrecking Yard Item
Item #: 11669 -
Core FMX transmission for a 1969 Mercury Cougar or Ford Mustang. Tag number PHB-E. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1969 Mercury Cougar with H code 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.
Availability: Out of Stock
Item #: 15397 -
Core FMX transmission for a 1969 Mercury Cougar or Ford Mustang. Tag number PHB-H. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1969 Mercury Cougar with M code 351-4V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.
Availability: Out of Stock
Item #: 15592 -
Core FMX transmission for a 1970 Mercury Cougar or Ford Mustang. Tag number PHB-P. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1970 Mercury Cougar with M code 351C-4V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.
Availability: Out of Stock
Item #: 27464 -
Core C6 transmission for a 1969 Mercury Cougar or Ford Mustang. Tag number PGA-Y or PGA-AE. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1969 Mercury Cougar S code with 390IP or 390-4V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.
Availability: Out of Stock
Item #: 31093 -
Core C6 transmission for a 1969 Mercury Cougar or Ford Mustang, with Q or R code 428CJ engine. Tag number PGB-AF1. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1969 Mercury Cougar with 428CJ engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.
Availability: Used / Wrecking Yard Item
Item #: 33291 -
Core FMX Transmission valve body for any 1969 Mercury Cougar or 1969 Ford Mustang with code "X" transmission code on the door tag. This is only for 1969 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is...
Availability: Out of Stock, On Order
Item #: 33295 -
Core FMX Transmission valve body for any 1969 Mercury Cougar or 1969 Ford Mustang with code "X" transmission code on the door tag. This is only for 1969 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is...
Availability: Out of Stock, On Order
Item #: 33296 -
Core FMX Transmission valve body for any 1969 Mercury Cougar or 1969 Ford Mustang with code "X" transmission code on the door tag. This is only for 1969 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is...
Availability: In-Stock Item
Item #: 32454 -
Coil bracket mounting bolt for all V-8 engines as found in 1967-73 Mercury Cougar and Ford Mustang. This3/8-16 bolt attaches the coil bracket to various places on the engines. Either on the intake manifold or the cylinder head. Will fit stock Ford cast iron intakes as found 1967-73. AMK bolt B-13722.
Availability: In-Stock Item
Item #: 32603 -
Bolt and nut for the clamping the coil into the coil bracket as found in 1967-73 Mercury Cougar and Ford Mustang. Fits all of the various coil brackets used 1967-73 on most all Ford engines. This is a 8-32x1-1/2, 1/4 hex headed fine thread bolt and nut. This is not the round headed slotted screw type that Ford also used.
Availability: In-Stock Item
Item #: 31425 -
Reproduction Speed or cruise control switch, for factory installed cruise control. Very rare option on a 67-69 Cougar or Mustang, also fits Thunderbird, Lincoln, Marquis. Keep in mind that these new levers will not come with the plastic plug at the end of the harness, you will need to use your old one, or you can splice as shown in the included installation sheet. As you know, these levers were made from plastic in the sixties and seventies. This new reproduction is machined from billet...
Availability: Used / Wrecking Yard Item
Item #: 31488 -
Relay for 1969 Mercury Cougar or Ford Mustang with factory speed control. This is the anti retard relay, identified with the plug with two male connectors. Mounts to the Regulator mounting bracket along with the Brake Release Relay.Ford part numbers C9ZA-9C733-B and C9ZZ-9C733-A.
Availability: Used / Wrecking Yard Item
Item #: 31444 -
Relay for 1968-69 Mercury Cougar or Ford Mustang with factory speed control. This is the brake release relay. Mounts to the Regulator mounting bracket. Ford part numbers C8ZA-9D737-A and C8ZZ-9D737-A.
Availability: Rare / NOS Part
Item #: 31706 -
NOS Speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. The 1968 Electrical manual shows a Lincoln part number of C7VA-9D752-G. Service replacement part number is D1VY-13305A. Would need to remove the white tilt bale collar prior to use.
Availability: Used / Wrecking Yard Item
Item #: 33397 -
Grade B speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G
Availability: In-Stock Item
Item #: 41344 -
This is one of the best small block Ford V-8 books on the market. It covers 260-289-302 V8 engines. Carburetor numbers, distributor numbers, covers all engine brackets, pulleys, and parts of Ford small block engines. 100's of pages with pictures, casting numbers, and explanations by year. A must for concours detailing and year by year correctness. Author Bob Mannel, covers small block V8 engines and components 1962-69. References all Ford cars that these engines came in. Mustang, Cougar,...
Availability: In-Stock Item
Item #: 41947 -
Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...
Availability: Used / Wrecking Yard Item
Item #: 14676 -
Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...
Availability: Out of Stock
Item #: 14252 -
This polyurethane steering coupler repair kit for your tilt column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. Some customers feel polyurethane improves steering feel. Replaces factory steering coupler on 1967 - 1973 cars. Most 1967 Mustangs with fixed steering columns do not have coupler.Replaces Ford Part #: C7OZ-3A525 Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...
Availability: In-Stock Item
Item #: 25907 -
Reproduction clevis for the tilt/tilt away steering column equipped Mercury Cougar or Ford Mustangs. This unit attaches the pawl cable to the vacuum motor shaft. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Used / Wrecking Yard Item
Item #: 25909 -
Used rubber washer for the locking pawl cable to cable guide used for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit fits against the cable side of the ninety degree angle. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts...
Availability: In-Stock Item
Item #: 11285 -
Emergency flasher bezel for the side of the tilt steering column. Reproduction bezel in black. Replaces most all tilt swing steering columns from 1967-69. Replaces Ford part number C9AZ-15C80-A, and an earlier part number starting that was likely C7SZ-15C580-A.
Availability: Used / Wrecking Yard Item
Item #: 15-0003 -
Fixed steering column from a 1969 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. Upper and lower mounting brackets, are available, but sold...
Availability: Used / Wrecking Yard Item
Item #: 15-0129 -
Used vacuum actuator for the tilt / tilt away steering column in the Mercury Cougar, Ford Mustang or Thunderbird. This unit was used through late 1968 and 1969 and has the embedded safety starter switch in good working order. 1967 through early 1968 actuators are white, where these units are black in color. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at...
Availability: Used / Wrecking Yard Item
Item #: 32896 -
Used tilt / tilt away steering column wiring harness for the 1969 Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Used / Wrecking Yard Item
Item #: 32895 -
Used wiring harness for the 1969 Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Ships Direct from Supplier (Except International)
Item #: 13752 -
American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process.This seat cushion foam is of a much softer lighter material than the other seat cushion foam that we offer. Much more comfortable and plush and about half the weight. Click on images to enlarge. ...
Availability: In-Stock Item
Item #: 13753 -
Sold as one-seat set including one bottom cushion and one backrest cushion.
Availability: In-Stock Item
Item #: 16748 -
Quality wiring reproduction for Perfect Circle brand of speed controls as found on most 1967-1971 Ford - Mercury - Lincoln automobiles. Main harness with Ford part number 9A840, can be used on a variety of model and years. Harness connects the servo, has grommet for firewall, and connectors under the dash. Jumper wire to the brake pedal.
Availability: Used / Wrecking Yard Item
Item #: 31157 -
Used speed control or cruise control switch for any 1969 Mercury Cougar or Ford Mustang. Very rare and expensive option for 1969. About 1% of 1969 Cougars had this option and way less than 1% of Mustangs had this option. Switch hangs down over the radio. Look in your owners manual for exact location. Ford part number C9ZA-9D743-C. *Switch only - Knob sold separately.
Availability: Out of Stock
Item #: 25693 -
RUG-AE2 Original equipment 4 speed top loader transmission from a 1969 Mercury Cougar with engine code R 428 Cobra Jet or engine code Q 428 Cobra Jet only. Transmission code 6 on the door tag, this would be a close ratio 4 speed transmission with a 2.32 ratio first gear. Ford master part number C8ZZ-7003-D.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for...