Home > 1973 Mercury Cougar
All Available Parts - 1973 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 201-300 of 3317
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 25437 -
This 1.5 degree wedge properly sets the pinion angle for the drive shaft.The Mercury Parts Catalog states that this part is installed "As Required".Sold individually, two required per vehicle.Orientation: Narrow end towards the front of the car.
Availability: Used / Wrecking Yard Item
Item #: 25436 -
This 1 degree wedge properly sets the pinion angle for the drive shaft.The Mercury Parts Catalog states that this part is installed "As Required".Orientation: Narrow end towards the front of the car.
Availability: Ships Direct from Supplier (Except International)
Item #: 20509 -
Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new 4 pinion Trac-Loc unit, new Motive ring and pinion gears, new Timkin bearings, new crush sleeve, new bolts, and new seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. There are various ring and pinion (gear) ratios and axle splines available, if you are unsure of what you need it is best to call (503) 463-1130 for your order. This is a drop ship item. *Note - New...
Availability: Ships Direct from Supplier (Except International)
Item #: 20510 -
Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For use with 28 splined axles, but can be custom...
Availability: Ships Direct from Supplier (Except International)
Item #: 19802 -
Limited slip 9 inch Ford third member rebuilt with all new or reconditioned parts. Rebuilt 4 pinion Trac-Loc unit, with new clutches, steels, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using standard 9 inch cases with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit was used in Cougars and Mustangs, but also any other Fords...
Availability: Ships Direct from Supplier (Except International)
Item #: 19801 -
Limited slip 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and new a seal. Rebuilt using the standard 9 inch case, with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it works for any other Mercurys or Fords with a 9 inch...
Availability: Ships Direct from Supplier (Except International)
Item #: 19803 -
Limited slip 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967-1973 standard 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used on any other Ford or Mercury with a 9 inch drop out center section. Because of all the various ring and pinion...
Availability: Ships Direct from Supplier (Except International)
Item #: 19798 -
Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch case with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it can also be used for any other Ford or...
Availability: Ships Direct from Supplier (Except International)
Item #: 19800 -
Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a 1967-1973 nodular 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used in any other Ford or Mercury with a 9 inch drop out center section. Because of all the...
Availability: Ships Direct from Supplier (Except International)
Item #: 19797 -
Limited slip, nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Used modern design Detroit Locker unit, new Richmond ring and pinion gear, new Timkin bearings, new selective size sleeve, new bolts, and new seal. Rebuilt using 1967-1973 nodular 9 inch cases with oil fill plug, for 28 or 31 splined axles. This unit was used in 1967-73 Cougars and Mustangs, but it also came in any other Fords or Mercurys with a 9 inch drop out center section....
Availability: Used / Wrecking Yard Item
Item #: 25359 -
Shaft diameter 3 inches, length 53-13/16 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length. *TRIVIA* All 71-73 stick shift 351C-4V powered Cougars were equipped with the top loader 4 speed transmission.
Availability: Used / Wrecking Yard Item
Item #: 25357 -
Check your door data plate for code X in the transmission box. Shaft diameter 3 inches. Length 54-1/4 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.
Availability: Used / Wrecking Yard Item
Item #: 25358 -
Check your door data plate for code U in the transmission box. Shaft diameter 3 inches. Length 50-13/32 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length. Ford part # D1WY-4602-C.*NOTE* Excludes Q code 351CJ engines.
Availability: Used / Wrecking Yard Item
Item #: 25360 -
351CJ denoted by a Q in the 5th position of the VIN. All automatic equipped Cobra Jets came with a C6 transmission. Shaft diameter 3-1/2 inches. Length 50-13/32 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.
Availability: Used / Wrecking Yard Item
Item #: 16-0049 -
31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX cars. *Excludes 351C-4v and 351CJ engines.
Availability: In-Stock Item
Item #: 41624 -
Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually
Availability: In-Stock Item
Item #: 10577 -
[No Description Provided]
Availability: In-Stock Item
Item #: 45631 -
Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Does not come with weather strip.
Availability: In-Stock Item
Item #: 30405 -
Reproduction four piece aluminum rear window moulding / trim set for the 71 - 73 Cougar or Mustang. Customers have mentioned that these are very hard to install on the Cougar. Ford part #s D1ZZ-6542405-A, D1ZZ-6542404-A, D1ZZ-6542430-A, D1ZZ-6542431-A.
Availability: In-Stock Item
Item #: 31902 -
Reproduction pair of windshield mouldings / trim for the Mercury Cougar or Ford Mustang coupe. Replaces Ford part #'s driver side D1ZZ-6503145-A, passenger side D1ZZ-6503144-A.
Availability: In-Stock Item
Item #: 45613 -
Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible.
Availability: In-Stock Item
Item #: 19469 -
Complete kit with 12 white plastic mounting clips, 2 black plastic mounting brackets that attach rocker mouldings to scoops, 2 aluminum rocker mouldings and 2 chrome plated scoops.
Due to supplier shortage, the metal rocker panel clips are not available at this time. Click Here to View Installation Instructions These are correct for 1969 only but can be used on any year 1967-1973 ...
Availability: In-Stock Item
Item #: 10580 -
Reproduction rocker moulding / trim end clip for the Mercury Cougar. This clip is a steel clip with a wire like the original. These units are technically for the 1969 and 1970 Cougar, but they will also work well with the 1968 rocker moulding / trim. Four of these clips were used on all 1969 Cougars except for the Sport Special which used two. The 1970 Cougar also uses two per car. Sold individually.Will work on 71-3 with modification. ...
Availability: Used / Wrecking Yard Item
Item #: 53195 -
Low fuel relay for all 1971-73 Mercury Cougar XR7 models, body code 65F and 76F only. Stamped D1WF-10A968-AA. These are tested and working relays.Fits 1971 Cougar XR7 Fits 1972 Cougar XR7Fits 1973 Cougar XR7
Availability: Used / Wrecking Yard Item
Item #: 10173 -
Used in 1971-73 Mercury Cougars and Ford Mustang for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.25" x 13/16" and has a single green dot. Box is marked FASCO, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Ford part number D1MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...
Availability: Used / Wrecking Yard Item
Item #: 12970 -
Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1971-73 Mercury Cougar and Ford Mustang. This relay controls a buzzer as a reminder to turn off the headlights or remove the key, when the door is opened.Replaces Ford part number D1AB-10C838-A or D1AZ-10C838-A.
Availability: Used / Wrecking Yard Item
Item #: 22672 -
Used 20 amp circuit breaker for either 69 - 70 or 71-73 Cougars.Mounted on the Starter solenoid in 69-70 cougars for convertible tops or power windows, and also on 71-73 Standard Cougars for convertible tops, power windows, heated back light, power seats or seat back release.On the 71-73 XR7 the circuit breaker was mounted next to the starter solenoid on a junction block. Different wire diagrams, owner / shop manuals list this circuit breaker in both locations, possibly due to multiple...
Availability: In-Stock Item
Item #: 31555 -
Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.
Availability: Used / Wrecking Yard Item
Item #: 32081 -
Passenger side chassis bumper bracket for the rear axle. Passenger side as removed from a 1967-73 Mercury Cougar. Good condition bracket, road tested, but not salt road tested. Ships as shown, cut with generous margins around the original bracket.
Availability: Used / Wrecking Yard Item
Item #: 32080 -
Driver side chassis bumper bracket for the rear axle. Passenger side as removed from a 1967-73 Mercury Cougar. Good condition bracket, road tested, but not salt road tested. Ships as shown, cut with generous margins around the original bracket.
Availability: Rare / NOS Part
Item #: 26719 -
Ford original eye let bushing 100% correct for the 67-69 Cougar without competition handling, but will fit on any 67-73 cat including those with competition handling. Ford Part #: C4DZ-5781-C.
Availability: In-Stock Item
Item #: 41430 -
Reproduction anti-squeak pad for the leaf springs found on the Mercury Cougar or Ford Mustang. This little unit goes between each individual leaf spring and prevents metal to metal contact. These are sold individually and eight are required per car. Our reproduction leaf springs come with this pad pre-installed. Replaces Ford part # C0AA-5586.
Availability: In-Stock Item
Item #: 41270 -
This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD INDIVIDUALLY. Replaces Ford Part #: KC-55490-A.
Availability: In-Stock Item
Item #: 13929 -
This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD AS SET OF 8. Replaces Ford Part #: KC-55490-A.
Availability: In-Stock Item
Item #: 18990 -
Correct leaf spring eye bushing bolts for the 1968 - 1973 Mercury Cougar. 5" in length. Set includes 2 bolts and 2 nuts. Replaces Ford Part #: C7ZZ-5781-A.
Availability: In-Stock Item
Item #: 26749 -
This eyelet bushing is made from higher grade rubber and unlike the NOS and other reproductions has a solid center shaft. The center shaft of this reproduction is a flat piece of steel that is bent into a circle to make the shaft for the eyelet bolt to go through, just like NOS. Two per car, these are used on one end of the leaf springs and the shackles are used at the other end. Replaces Ford Part #: C7WY-5781-A, C4DZ-5781-C, C5ZZ-5781-A, D3ZZ-5781-B. ...
Availability: In-Stock Item
Item #: 18987 -
Poly eyelet bushing that will fit any 1967 through 1973 Mercury Cougar. Replaces Ford Part #: C4DZ-5781-C.
Availability: In-Stock Item
Item #: 26720 -
Leaf Spring U Bolt for the 1967 - 1973 Mercury Cougars with isolators. Will work on any 67-73 Cougar. Does not feature flattened area at top like original. Includes 1 'U' bolt and 2 nuts. 4 total U-bolts needed per car. *Note - For use with Cougar shock plate, angled wedge, rubber isolators and retainer boxes. Inside Height: 6-3/4"Inside width: 2 7/8" (Same as axle tubes) Replaces Ford Part #: C7WY-5705-A. ...
Availability: Used / Wrecking Yard Item
Item #: 24632 -
Application: most 1967-1973 with any V-8 engine. A Right and Left bracket are needed for most applications. Including all 1968 - 1970 428 CJ automatic transmission Cougars. **Excludes 1969 - 1970 Boss 302 & 428 Cobra Jet 4 speed Cougars. That application had staggered rear shock plates. Hint - that would be two C9OZ-5796-C right side shock plates.Replaces Ford part number C9OZ-5796-B.
Availability: In-Stock Item
Item #: 26716 -
Correct shackle for all 1967 through 1973 Cougars, except those manufactured between 10/70 and 9/71. Measures 3-1/2 inches from center to center. Bushing dimensions: Length 1 1/8", outside diameter 1" (shaft piece) - 1 1/4" (end piece), hole diameter 1/2" Sold individually, two required per car. Replaces Ford 5630 shackle kits that include bushings C4GY-5781-A and D4DZ-5781-A.
Availability: Used / Wrecking Yard Item
Item #: 24587 -
Correct length (3-1/2 inches from center to center) and construction shackle for all 1967 through 1973 Cougars, except those manufactured between 10/70 and 9/71. Ships complete - 2 piece shackle with original nuts. New bushings not included, but recommended. Sold individually, but two are required for the rear suspension. Replaces Ford 5630 shackle kits that include bushings C4GY-5781-A and D4DZ-5781-A.
Availability: In-Stock Item
Item #: 18988 -
Complete Set of 1" leaf spring rubber bushings for the rear eye of the spring shackle. Sold in packages of 8, 4 per side. Correct size for the 1967 - 1973 Mercury Cougar except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: D4DZ-5781-A. *except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71.
Availability: In-Stock Item
Item #: 18986 -
Complete Set of 1" leaf spring poly bushings for the rear eye of the spring shackle. Sold in packages of 8, 4 per side. Correct size for the 1967 - 1973 Mercury Cougar except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: D4DZ-5781-A. May be dropshipped. *except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71.
Availability: In-Stock Item
Item #: 42183 -
Set of Four Reproduction Rear Leaf Spring Center Mount Insulator Pads for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody...
Availability: In-Stock Item
Item #: 11324 -
These coarse thread nuts have an integrated lock washer with serations for the Mercury Cougar or Ford Mustang. They will ONLY work with the U-Bolts used in conjunction with the lowering kits. The thread size is 7/16"-14. *NOTE* Eight of these are required per car and are sold individually.
Availability: In-Stock Item
Item #: 26617 -
Reproduction Rear Leaf Spring Center Mount Insulator Pad for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody StyleNotesYearMercur...
Availability: Ships Direct from Supplier (Except International)
Item #: 43805 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43808 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43811 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43814 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43817 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43820 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43823 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43826 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43830 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43833 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43836 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43839 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43803 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43806 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43809 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43812 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43815 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43818 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43821 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43824 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43827 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43828 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43831 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43834 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Ships Direct from Supplier (Except International)
Item #: 43837 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Used / Wrecking Yard Item
Item #: 21607 -
Used rear leaf spring retainer for 1968 -73 Mercury Cougar with standard or non-GT / non- competition handling suspensions. Additionally it fits most 1966-70 Mercury Comet / Montego, 1970-71 Ford Torino. Identified with a stamped number "6" on the top. The inside height is 1-3/4 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be some erosion due to...
Availability: Used / Wrecking Yard Item
Item #: 19701 -
The majority of the rocker moulding end clips we get look like this unit in that the stud is broken or the wire tensioner has been broken off. Putting a new stud in one of these clips is not a hard job.
Sold Individually.
Availability: Used / Wrecking Yard Item
Item #: 25394 -
Ten of these plastic clips are required per car, five on each side. Original clips with D1ZB-6510182-AA engineering number imprinted on them. Sold Individually.
Availability: Used / Wrecking Yard Item
Item #: 20116 -
SBVALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1968-1971 Mercury Cougar and 1968-73 Ford Mustang with 289/302/351W engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2OZ-6582-C & D2OZ-6582-D. *Note - This cover will not work on a 351 Cleveland engine.
Availability: Used / Wrecking Yard Item
Item #: 14-1240 -
These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.
Availability: In-Stock Item
Item #: 11600 -
Bulk pack of 100 oval head phillips screws for door and window crank handles.
Availability: In-Stock Item
Item #: 32500 -
These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.
Availability: In-Stock Item
Item #: 41154 -
Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.
Availability: In-Stock Item
Item #: 41238 -
Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.
Availability: In-Stock Item
Item #: 27463 -
Original Ford style fasteners used on most all Ford products starting in 1968. Sold in pairs. Zink (dark silver)
Availability: In-Stock Item
Item #: 41306 -
These are the screws that are used to attach the door latch to the door shell on the 67 - 73 Cougar or Mustang. Sold in a set of 6.
Availability: In-Stock Item
Item #: 41359 -
Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.
Availability: In-Stock Item
Item #: 41256 -
1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)
Availability: In-Stock Item
Item #: 10745 -
Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well. Sold individually. 24 required per car, set of 24 also available. ...
Availability: In-Stock Item
Item #: 27468 -
New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...
Availability: Out of Stock
Item #: 32909 -
24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well. Also sold individually.
Availability: In-Stock Item
Item #: 41037 -
Replaces Ford part # C2DZ-6A529
Sold Individually.
Availability: In-Stock Item
Item #: 41002 -
This is the shorter version of the top-loader with no "+" on the head.
Sold individually
Availability: In-Stock Item
Item #: 41023 -
Replaces Ford part # 385664-S
Availability: In-Stock Item
Item #: 41228 -
Sold individually
Zinc (dark silver)
Availability: In-Stock Item
Item #: 41245 -
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).
Availability: In-Stock Item
Item #: 41229 -
Sold individually
Zinc (dark silver)
Availability: In-Stock Item
Item #: 41239 -
Sold individually
Zinc (dark silver)
Availability: In-Stock Item
Item #: 14187 -
This clip holds the speedometer cable gear to the end of the cable. Replaces Ford Part # : C1DZ-17292
Availability: In-Stock Item
Item #: 41243 -
Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.
Availability: In-Stock Item
Item #: 41360 -
These little rivets are used to affix the ID tag to the passenger side of the 3 and 4 speed top-loader transmissions. Most tags are held in place by two rivets but on some only two are used from the factory.
Availability: In-Stock Item
Item #: 41244 -
Sold individually.
Zinc Dichromate (yellow-rainbow)
Availability: Out of Stock
Item #: 41416 -
Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: In-Stock Item
Item #: 41166 -
Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...