All Products

Used trunk plate or bracket for mounting the "J" bolt for the spare tire. Several versions of this bracket, this is the most common one. Mounts flat to the trunk floor surface on all 1967-70 Mercury Cougar hard tops, with full sized spare tires. Additionally, 1971-73 Mercury Cougar convertibles. We cut these out of the trunk floors, so there will be some metal preparation for the customer. Ford part number C7AZ-6247076-A.

Used trunk plate or bracket for mounting the "J" bolt for the spare tire. Several versions of this bracket. Mounts on a corner of the trunk floor surface. 1969-70 Mercury Cougar convertibles, with full sized spare tires. Additionally, 1971-73 Mercury Cougar hard tops. This folded bracket was also used with cars with space saver spare tires, or trunk mounted batteries. We cut these out of the trunk floors, so there will be some metal preparation for the customer. Ford part...

Used bracket for attaching the steering column upper bracket to the brake pedal hanging bracket. Has a slot as shown. Fits all 1969 Mercury Cougar and Ford Mustang with either tilt or fixed steering columns.Shows up in the exploded views as Ford part number 3678.

Used windshield wiper mounting bracket for any 1967-68 Mercury Cougar or Ford Mustang. Part of the wiper motor assembly in the Master Parts Catalog, so no Ford number found.

Power steering hose bracket for early model Mustangs.

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang.Sold as a pair and are not side specific. 

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Fits all 1969-70 Mercury Cougar and Ford Mustang. Sold as a pair and are not side specific. 

Rear Wheel Cylinder (7/8", Left Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller. You can find the premium concours correct version here.

Rear Wheel Cylinder (7/8", Right Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller.You can find the premium concors correct version here. Replaces Ford Part #: C20Z-2262-B, C3AZ-2262-B, C4TZ-2262-A, C60Z-2262-A, D2ZZ-2262-A, D3TZ-2262-A, D3ZZ-2262-A. ...

Rear Drum Brake Wheel Cylinder for 390, 427, 428 w/ Front Disk Brakes (13/16", Right Hand & Left Hand same) You can find the premium concours correct version here. Replaces Ford Part #: C7ZZ-2262-A

Rear Wheel Cylinder (29/32", Right Hand) Fits either Right Hand or Left Hand. Sold individually, 2 required per car. Replaces Ford Part #: C3OZ-2262-B and D2ZZ-2262-B.

Rear Wheel Cylinders for 4 Wheel Drum Brakes (15/16", LH). Replaces Ford Part #: C7AZ-2262-C.

Rear Wheel Cylinder 29/32 inch bore, right hand fits passenger side of any 1969 with 2 inch wide rear brake shoes. This wheel cylinder orients the hard line to the rear of the vehicle. 1970-73 wheel cylinders are oriented towards the front.

Rear Wheel Cylinder for 4 Wheel Drum Brakes (15/16", RH) Replaces Ford Part #: C7AZ-2261-C.

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

Reproduction proportioning valve line for Mercury Cougar and Ford Mustang.

Reproduction proportioning valve line for Mercury Cougar and Ford Mustang.

These are the two lines that connect the proportioning valve to the distribution block on the Mercury Cougar or Ford Mustang.Proportioning valve is not included in this kit, only the two brake lines. Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...

Used driver (left hand) side brake shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Left side screws are identified by an "L" on the end of the screw under the socket and a single groove machined into the pivot nut. Original Ford part number for the passenger (right hand) side is...

Used passenger (right hand) side brakes shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Right side screws are identified by an "R" on the end of the screw under the socket and a two grooves machined into the pivot nut. Original Ford part number for RH or passenger side is C2OZ-2041-A,...

Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. We have glass bead blasted rust from inside, chrome is not perfect but part is functional. Originally came stamped ROBBINS - JR - 7600 or HAMILL H-000, we randomly pick them for you, no guarantee as to which supplier yours will have originated from.

Concours correct reproduction with correct red finish exact to original Ford part number c8oz-7583-a specifications

One used anti rattle spacers / guards that go between the fender and the cowl on each side. The majority of 1969 Cougars and Mustangs used a black foam block glued to the cowl but in late 1969 and all of 1970 these wedge shaped rubber parts were used. Replaces Ford part number C9ZZ-16758-A.

This is the rubber that goes into the bracket of the bottom of the center of the door, for 1969-1970 Mercury Cougar and Ford Mustang glued-in door glass.  Note that this bumper is substantially shorter than the 70  bolt-in door glass version.   See D0ZZ-6521762-A for the 1970 bolt-in door glass version.  If you are swapping out a door on a 69 or a 70 don't forget that the door glass is different between the years and, if you have to swap out the glass, you will...

Used upper rear bumper bracket for any 1973 Mercury Cougars. Right and left are the same, two needed per car. Ford part number D3WY-17A750-A.

Sold individually, two required per car. Right is the same as left. These Western rear bumper brackets are not heavily rusted, the threads are in perfect shape and they are not bent. Master part number C7WY-17A750-A.

D3WY-17A820-A This is one of the end brackets that mounts the outer bumper shell to the bumper beam. "L" shaped bracket, most have a stamped number of 4928A01 on them. Sold individually, 2 needed per bumper.

This is a metal "C" channel that glues to the bottom center of the glued-in door glass on 1969 and early 1970 Mercury Cougar and Ford Mustangs. This channel, helps protect the glass when lowered to the rubber stop at the bottom of the door. Ford part # C9ZZ-214A16-A. *HINT* Use the same professional grade of glass adhesive that you use for bonding the door glass to the two glass mounting brackets. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In...

Replacement tail shaft bushing, for all 1964-73 C4 transmissions.

Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions. 

C9AZ-13A164-B Inner grille bushing, where the hidden headlight hinge pivots. Hole size is 3/4", shaft size is 1/2". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights.

New reproduction of the grommet found at the bottom of nearly any Ford steering column starting in 1970 for the transmission lockout rod. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used outer bushing for the hinge pivots for the hide-away headlights on the Mercury Cougar. Hole size is 5/8", shaft size is 3/8". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights. Ford part # C9AZ-13A164-A. ...

Reproduction pair of brass 3/8 ID bushings for the clutch rod. Protects clutch equalizer and rod, and removes excess play.We also sell these in nylon. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it...

Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-J.

Rubber construction, sold in pairs only. This is the typical bar found on 428CJ and Boss 302 Cougars.

Standard size front sway bar bushings were 3/4 inch from 1967 - 1970. Rubber construction, sold in pairs only. Replaces Ford Part #: C7OZ-5493-C or C6OZ-5493-B.

There were two versions of this button and this is the shorter of the two found on the 1968 XR7. Has good internal spring and pit free knob. Used in conjunction with the 1968 lens with a larger pass through hole.

Reproduction front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. These are made just like the originals, are concours correct and includes the firewall seal and firewall bracket. Replaces Ford part # C7ZZ-2853-A.

Under dash bracket used to mount the pull cable for the fresh air vent on the driver side of your Mercury Cougar or Ford Mustang.

Used mounting and indexing bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket goes behind the dash panel and keeps the vent cable attached and indexed correctly. A 7/16-14  hex nut is also needed for mounting the cable. (Sold separately)Replaces Ford part number D1WY-6501822-A.

This used emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. Replaces Ford part # C6OZ-2A602-A.

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford Part # C7ZZ-2A808-A.

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford part # C7ZZ-2A808-A.

Sold as a pair. These often become dislodged due to the force required to be applied after they have rusted in place for decades. Located at the bottoms of the fenders.Ford part number 359613-S2.

Each kit contains the seals for one caliper assembly. Replaces Ford Part #: C8ZZ-2B120 and #C8ZZ-2B121Check out our caliper tips and tricks video below: ...

Reproduction disc brake caliper transfer tubes for your 1967 Mercury Cougar or Ford Mustang. Includes both left and right lines.

Factory original turn signal canceling cam. Originals were molded in white, reproductions are molded in black. Repros also available from us. Without this part that self attaches to the back of your factory steering wheel, you will be turning off your blinkers manually. Click up, click down... *NOTE* We have no good reason to encourage you to purchase this hard to find original over the reproduction, unless you just gotta have it. **NOTE** Need help diagnosing a Cougar turn signal problem?...