Home > 1969 Mercury Cougar
All Available Parts - 1969 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 601-700 of 5299
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 12327 -
8-32 screw for attaching the window regulator drive arm slide
Availability: In-Stock Item
Item #: 11-0409 -
Used bolt for installing the door glass window run on any 1969-70 Mercury Cougar or Ford Mustang. This is the lower bolt that goes into the bottom of the door. 1/4-20 threads, hex head but a shallow hex head, Originally installed with a rubber seal, which is not included. 7/16" hex head, these had a Ford part number of 379513-S100. 2 needed per door, 4 per car, sold individually.
Availability: In-Stock Item
Item #: 31162 -
Reproduction door glass run. This is the metal tube that the windows go up and down on, sometimes called an elevator shaft. Left side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Check out our used door glass runs, original Ford and lower priced. NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. OK reproduction, but the...
Availability: In-Stock Item
Item #: 30538 -
Locking nut for attaching the door window regulator to the window channel bracket on any 1969-70 Mercury Cougar or Ford Mustang. While we do not sell the T-bolts for attaching to the regulator (T-bolt Ford Part # C8SZ-6523274-A), we do have a retainer to keep it in the front channel bracket. Find it here. This is not an exact replica of the t-bolt lock nut, but is a functional replacement part. Replaced Ford part #: 34975-S ...
Availability: In-Stock Item
Item #: 31838 -
These inserts snap into your window elevators, four per elevator, eight per door for a total of 16 per car. Often the originals are worn down from lack of lubrication which will cause your door glass to rattle. The originals were more of a clear plastic, these are white in color. These do not fit quite as well as the originals, but work as long as you are OK with the slight play. For a tighter fit, we recommend that you see the customer reviews of this product for suggestions that...
Availability: In-Stock Item
Item #: 31663 -
New bolt for installing the door glass window run on any 1969-70 Mercury Cougar or Ford Mustang. This is the lower bolt that goes into the bottom of the door. 1/4-20 threads, hex head but a shallow hex head, Originally installed with a rubber seal, which is not included. 7/16" hex head, these had a Ford part number of 379513-S100. 2 needed per door, 4 per car, sold individually. Black silicone is a good substitute for the seal.
Availability: In-Stock Item
Item #: 31898 -
383278-S 1/4-20 Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs. This is a new or reproduction part from AMK.
Availability: In-Stock Item
Item #: 32190 -
This gear was used on Cougars starting in 1969 and then Mustang in 1971. Fits pretty much every (common) Ford power window motor except for the unique "pancake" style motors found with the 1/4 windows on the Cougar and Mustang. Includes metal plate as shown. Replaces Ford part # D0AZ-62234A24. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969...
Availability: In-Stock Item
Item #: 26814 -
These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Sold individually and four are required per car. Replaces Ford part #: C9ZZ-6522204. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...
Availability: In-Stock Item
Item #: 14-0011 -
3M brand two part channel bonding adhesive for gluing in the Mercury Cougar or Ford Mustang door side glass and rear quarter glass. This is the best product on the market for re-gluing those troublesome 1969 side windows. We use this product for our own cars here at WCCC and have found an applicator that works great. If you just need an applicator to do just your car, we have a 60 day loaner you can use right here. However, if you are doing multiple cars or other parts, you may want to...
Availability: In-Stock Item
Item #: 11801 -
These are great for your back seat belts or convertibles that did not use retractors in the front. They are an exact copy of the originals that were available as a dealer option from 1964 and up. Sold Individually. Made in U.S.A. Replaces Ford Part #: C4AZ-65611A06. Customer feedback: I just wanted to tell that your delivery has arrived today. Thanks a lot! Never ever ordered something (not even here in Germany) and got it that fast. Awesome! My next orders will go to your place and I will...
Availability: Out of Stock
Item #: 14-0060 -
This is an example of the best set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags.Check out our video "All about seat belts" below. ...
Availability: In-Stock Item
Item #: 41825 -
Includes one lap belt, the mounting bolts and washers.sold individually
Availability: In-Stock Item
Item #: 41826 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Sold individually
Availability: In-Stock Item
Item #: 41828 -
Great looking replacement style seat belt. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. These are great lap belts for convertible cars that don't use retractors. We suggest using seat belt anchor bolts for an easy installation of these aftermarket lap seat belts. This kit does come with installation hardware, but the threads on the bolt are coarse, and will not bolt into your original threaded anchor points. sold individually ...
Availability: In-Stock Item
Item #: 41895 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colorssold individually
Availability: In-Stock Item
Item #: 41833 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41829 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41822 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41823 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41832 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 13711 -
These are era-correct looking seat belts at an affordable price. These are not Concours reproductions, but have the correct vintage look used by Ford on multiple cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals.Sold individually Includes: 1 Complete non-retracting seat belt (includes both male and female side)2 Bolts, nuts, and lock washers
Availability: In-Stock Item
Item #: 13708 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13706 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13710 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13715 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually
Availability: In-Stock Item
Item #: 13714 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13712 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! sold individually
Availability: In-Stock Item
Item #: 13707 -
This is an original looking seat belt at an affordable price. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! SOLD INDIVIDUALLY
Availability: In-Stock Item
Item #: 13709 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually
Availability: Used / Wrecking Yard Item
Item #: 14-5001 -
This is a general listing for anything and everything seat belt related. We can't go through and list every single seat belt part we have here, but chances are, we have what you need. If you're looking for used belts, all you have to do is call our seat belt guy (his name is Junior, at extension 209) and he'll go out in the warehouse and put together a set to match your needs and price range. We have everything from dirty old faded belts with minor rust on the chrome, to super nice, clean,...
Availability: Used / Wrecking Yard Item
Item #: 14-0073 -
This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.
Availability: Ships Direct from Supplier (Except International)
Item #: 22557 -
Set of BLACK seat belts for the 69 Cougar or Mustang Coupe (convertibles did not use retractors). Every inch of these belts has been expertly re-done. The webbing, stitching, chrome, bezels, plastic face plate and even the Ford production tag has been meticulously restored. These belts are for the Cougar or Mustang enthusiast who wants the absolute best. Included in this set are the front lap / shoulder belts with retractors, and the four belts for the back seat. Hardware sold separately. As...
Availability: Used / Wrecking Yard Item
Item #: 14-0021 -
When placing your order, be sure to leave a note as to which color you're looking for and we'll do our best to find them for you. Limited quantities available. This colored face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are...
Availability: In-Stock Item
Item #: 30179 -
Reproduction set of front seat belt bolts for your 69 - 70 Cougar or Mustang. Included are the 4 bolts, 4 large washers and 4 anti rattle gaskets.
Availability: In-Stock Item
Item #: 30858 -
Premium quality deluxe shoulder and lap belt with re-tractor. Deluxe belts with chrome bezels were equipped on many 68 - 69 Cougars and Mustangs. If you prefer the standard version with a black band on the buckle, just mention it and we will change it out at no extra cost. Many of our customers are calling this a "concours" set, but they do not qualify for that. If you look close you will see the nylon webbing has four bands which is correct for 1968. 1969 and up used a three band pattern on...
Availability: In-Stock Item
Item #: 30884 -
These reproduction face plates fit inside the buckle bezel on the two piece type seat belt buckle cover. Sold as a pair. You can use your existing spacer, or if you're missing one, you can find it here. Check out our video "All about seat belts" below. ...
Availability: In-Stock Item
Item #: 30898 -
Now you can restore your 1968-72 Cougar or Mustang’s deluxe seat belt buckles back to their original showroom condition by replacing cracked, broken, or missing components with the new seat belt buckle restoration kit. Tooled to the original factory specifications from OEM quality injected molded black plastic. This seat belt buckle kit features the correct texture grain pattern and starburst medallions for a perfect restoration. The release button and spring are included. One kit does a pair...
Availability: Used / Wrecking Yard Item
Item #: 14-1016 -
Hard to find without being faded, frayed or rusted buckle. Rarely, if ever will our used shoulder belts look this pristine as they are prone to sun fade. Sold individually, 2 required per car, hardware sold separate. Contact us for colors other than black. Check out our video "All about seat belts" below. ...
Availability: Used / Wrecking Yard Item
Item #: 14-1033 -
This is an example of the best set we can come up with. This is a standard set with black buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...
Availability: In-Stock Item
Item #: 31000 -
Premium quality deluxe rear lap belt. Deluxe belts with chrome bezels were equipped on many 68 - 69 Cougars and Mustangs. If you prefer the standard version with a black band on the buckle, just mention it and we will change it out at no extra cost. Many of our customers are calling this a "concours" set, but they do not qualify for that. If you look close you will see the nylon webbing has four bands which is correct for 1968. 1969 and up used a three band pattern on the webbing. Notice it...
Availability: Used / Wrecking Yard Item
Item #: 14-1011 -
Both deluxe and standard used the same retractor in 1968 - 1969 and left is the same design as right. Grade "B" retractors will be 100% functional but cosmetically will show a crack in the plastic holster, and may have minor rust on chrome. Keep in mind no retractor was used in convertibles until 1972, only a lap belt. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Check out our video "All about seat belts" below. ...
Availability: Used / Wrecking Yard Item
Item #: 14-1014 -
This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original starburst decal, which will be faded and need replacing. Find the replacement decals here. Spring is included.
Availability: Used / Wrecking Yard Item
Item #: 14-1012 -
Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...
Availability: Used / Wrecking Yard Item
Item #: 14-0000 -
This is the complete one piece seat belt buckle cover which comes with the face plate (with the round cutout for the push button) and the bezel all in one. This version is handy when you don't want to deal with multiple parts (as is the case with the separate face plate and bezel version). Simply remove your old cracked or broken cover, replace the metal spacer, and pop this cover into place and you're ready to go! You can use your existing spacer, or if you're missing one, you can find it...
Availability: Used / Wrecking Yard Item
Item #: 14-0100 -
This face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are going to be missing that piece, because after all......that dampener has been in there for up to 46 years! (this doesn't effect its useability). You can use your existing...
Availability: Used / Wrecking Yard Item
Item #: 14-0110 -
Used seat belt buckle bezel for the Mercury Cougar, Ford Mustang, or Ford Torino. This is the outer portion of the two piece seat belt buckle cover. This is a good replacement part if you want to keep your car original. These bezels will be free of cracks and breaks. Please specify which color you're looking for when ordering. Keep in mind that there are only a handful of colored buckles available, so we'll do our best to get you the color you need. Check out our video "All about seat belts"...
Availability: In-Stock Item
Item #: 31017 -
Reproduction set of Deluxe seat belts for the 68 - 69 Cougar or Mustang Coupe. Some things you may want to notice are that although these are made to fit both 68 and 69, the webbing is the 68 style. 1968 belts had four rows of material that make up the belt and 1969 belts had three rows (as seen in the picture above). Also, the rear belts will not have the plastic sheaths that keep the belts from falling in between the seats. These belts are premium quality and come complete with deluxe...
Availability: In-Stock Item
Item #: 14-1037 -
Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above. Sold individually, one per buckle.
Availability: In-Stock Item
Item #: 32360 -
Finally! A cure for those peeling chrome bezels on your car with deluxe seat belts. If your plastic bezels on your 68-72 standard belts are two part construction, you can upgrade with these attractive bezels. Before these were reproduced we used to hunt high and low for good used units from rear belts out of parts cars. Perfect fit and great quality. Sold as a pair, six per car on coupes, four per car required on convertibles. Replaces Ford part # C8AZ-65611A72-A
Availability: Used / Wrecking Yard Item
Item #: 14-1018 -
This is an example of the best set we can come up with. This is a standard set that has the black buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...
Availability: In-Stock Item
Item #: 41889 -
These are Concours quality with correct bevel and markings.. Sold as a pair.
Availability: In-Stock Item
Item #: 14062 -
A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...
Availability: In-Stock Item
Item #: 26760 -
These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!
Availability: Ships Direct from Supplier (Except International)
Item #: 20047 -
Nice reproduction of the original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds. The supplier unfortunately does not include the hardware and we have yet to source any. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on...
Availability: In-Stock Item
Item #: 42020 -
This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...
Availability: Used / Wrecking Yard Item
Item #: 24731 -
This engine compartment lamp assembly includes lamp socket, bracket, mercury switch, and length of wire. A bit of investigation shows us that an inline fuse was used on the single wire and it has an amp rating of 7.5 amps.Replaces part # C9WY-15702-A
Featured!
Availability: In-Stock Item
Item #: 25875 -
Reproduction original style chin spoiler. Nice quality, fit and finish. Made from thin plastic just like the originals. Comes as bare black plastic, so we suggest coating with your favorite semi-gloss black paint for a more finished look. Take a look at the 1:33:00 mark in the video below to see how we compare the reproduction to the original: ...
Availability: In-Stock Item
Item #: 11337 -
Billet aluminum batter hold down bracket for all 1967-70 Mercury Cougar and Ford Mustangs. Maximum battery width 6-3/4 inches. We also have stainless steel hold down bolts available.
Availability: In-Stock Item
Item #: 11338 -
Stainless steel battery hold down bolts. Work with standard battery hold down brackets and the billet hold down bracket.
Availability: In-Stock Item
Item #: 30713 -
Reproduction 15 x 7 charcoal colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...
Availability: In-Stock Item
Item #: 30727 -
Reproduction 2 piece spinner assembly for the new HB45 Legendary Series aluminum wheel. The aluminum die cast threaded stem mounts from the back side of the wheel and the chrome spinner truly spins on from the front. Set screw is included to prevent loss. NOTE: Will only fit the HB45 Legendary WheelCheck out our video on Legendary Wheels below: ...
Availability: In-Stock Item
Item #: 30842 -
Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.
Availability: Used / Wrecking Yard Item
Item #: 31667 -
This listing is for the bottom part of the seat only, which is often what fails. Keep in mind that we do have a repair bracket for the hinge stud on the right hand side of this seat. This listing will save you a lot of money on shipping if you don't need the entire seat.
Availability: Used / Wrecking Yard Item
Item #: 31668 -
This listing is for the bottom part of the seat only which is often what fails. This listing will save you a lot of money in shipping if you do not need the entire seat.
Availability: Used / Wrecking Yard Item
Item #: 31669 -
This listing is for the upper part of the seat on a low back bucket with headrests (headrest not included). This listing will save you a lot of money in shipping if you do not need the entire seat.
Availability: Used / Wrecking Yard Item
Item #: 31670 -
This listing is for the upper part of the seat on a low back bucket with headrests (headrest not included). This listing will save you a lot of money in shipping if you do not need the entire seat.
Availability: Used / Wrecking Yard Item
Item #: 31680 -
Used and tested original sequential unit for the 1969 - EARLY 1970 Mercury Cougar. This unit will come with a 90 day warranty. Keep in mind that if you want to use the brighter LED's on your car, this original sequential system will not work. If you want to change over to LED, you will need the updated sequential unit which you can find here. If you need the sequential enclosure box, you find our used boxes here. ...
Availability: Used / Wrecking Yard Item
Item #: 31686 -
Used emergency flasher for the 1969 Mercury Cougar. This flasher either came in gold or silver. Ford Part number C9WB-13350-B1 or C9WB-13350-B2
Availability: In-Stock Item
Item #: 31694 -
Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a black background. *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels. ...
Availability: In-Stock Item
Item #: 31695 -
Reproduction castle nut for multiple applications, including the power steering control valve, strut rods, ram cylinder and ball joints on the 1967 - 1973 Cougar or Mustang. Dimensions: 9/16" - 18.
Availability: In-Stock Item
Item #: 31749 -
Reproduction pair of A/C vent registers for your 69 - 70 Cougar or Mustang. Sold as a pair. Replaces Ford part numbers: C9ZZ-19893-D driver side, C9ZZ-19893-C passenger side.
Availability: Out of Stock
Item #: 31803 -
Used convertible top flapper stopper. Technically called a "lasting", this is the thin strip of 1/16" thick metal that slides inside the sleeve of your convertible top to keep it from flapping. We will rarely have these on hand, so we've included the dimensions so that you can fabricate your own if needed. 2 required per vehicle.
Availability: Used / Wrecking Yard Item
Item #: 31816 -
Used wiring pigtail from the under dash harness to the door jamb switch on the driver side of the 69 Standard Cougar.
Availability: Used / Wrecking Yard Item
Item #: 31817 -
Used wiring pigtail from the under dash harness to the door jamb switch on the passenger side of the 69 Standard Cougar.
Availability: In-Stock Item
Item #: 31839 -
Parking brake return spring cup for the 69 - 73 Cougar or Mustang. This cup sits at the end of the spring and is held in place by an adjusting nut. It's used to keep the spring from sliding off of the front emergency / parking brake cable.
Availability: In-Stock Item
Item #: 31857 -
Reproduction retainer clip for the back up light switch wiring on the 67 - 69 Cougar or Mustang equipped with a 3 or 4 speed transmission.Replaces Ford part number C7ZZ-14163
Availability: Out of Stock
Item #: 31861 -
Used pair of 31 spline axles for the 68 - 70 Cougar or Mustang, equipped with the Boss 302, 427 and 428 CJ engines all with 9 inch rear axles. Most all other vehicles used 28 spline axles. Short axle 27-1/16" inches long and long axle 31-1/8" inches long. Ford part numbers C9OZ-4234-C and C9OZ-4234-D. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. ...
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 31871 -
Pair of reproduction license plate frames bearing the name of the the original Lincoln / Mercury dealer lot in San Jose, California. Chrome with the city and dealer name written in/on reflective material. Sold only as a pair.
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 31872 -
Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Inglewood, California. Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 31873 -
Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Portland / Beaverton, Oregon. Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.
Availability: Used / Wrecking Yard Item
Item #: 31887 -
Used front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. May or may not have threaded studs, or...
Spotlight!
Featured!
Availability: Ships Direct from Supplier (Except International)
Item #: 31892 -
Reproduction deck lid for the 69-70 Cougar. Exact reproductions of the originals, these deck lids are well fitting and are a perfect replacement for your old rusty lid. Does not include hardware or lock cylinder, shipped bare. Here's the installation kit for these reproduction deck lids. Keep in mind that this is an oversized package and will most likely have to be shipped through truck freight. Expect to pay up to $250 in shipping charges. ...
Availability: In-Stock Item
Item #: 31963 -
Reproduction coil spring seat pad for the 67 - 73 Cougar or Mustang. Sold individually, 4 needed per car.
Availability: In-Stock Item
Item #: 31969 -
Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a big block engine. This item requires a $30 core charge.
Availability: In-Stock Item
Item #: 31968 -
Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a small block engine. This item requires a $25 core charge.
Availability: Out of Stock
Item #: 31978 -
Remanufactured alternator for any 67 - 73 Cougar or Mustang. Specs: Rated at 55 ampsSingle V groove pulleyExternal fanPlug position at 5 o'clock
Availability: Used / Wrecking Yard Item
Item #: 31991 -
Used pair of red diffusers for the temperature or fuel gauge on the 69 - 70 Mercury Cougar. The wording (alternator, park, brake, oil etc.) is on the actual lens and not the diffuser, so these can be used on either gauge.Sold as a pair.
Availability: Out of Stock
Item #: 32002 -
Upper toque box patch panel plates for the 67-70 Cougar Coupe or 65-70 Mustang Coupe or Fastback.
Availability: Used / Wrecking Yard Item
Item #: 32035 -
Fits the 1969 Standard Cougar, good used housing with no rust or modifications.Ford part number C9WF-10843
Availability: Used / Wrecking Yard Item
Item #: 32037 -
Fits the 1969 Cougar XR7, good used housing with no rust or modifications.Ford part number C9WF-10843
Availability: Out of Stock
Item #: 32059 -
These plates were really clean before they were sent out for restoration, you can get your Oregon plates restored at http://oregonplates.com/NOTE: The plates and plate numbers pictured are exactly what you'll receive.
Availability: Ships Direct from Supplier (Except International)
Item #: 12820 -
Dark Red / Maroon floor mats for the 67 - 73 Cougar embroidered with the XR7 logo.
Availability: In-Stock Item
Item #: 32088 -
Reproduction silver walking cat emblem / insert for the 70 Eliminator T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 69 - 70 Eliminator, this handle will fit on any 67 - 73 Cougar with the automatic transmission.
Availability: In-Stock Item
Item #: 32111 -
Reproduction polished aluminum 600 CFM "Street Warrior" carburetor for the 67 - 73 Cougar or Mustang. Replaces Holley, Edelbrock, Carter AFB, and Autolite style carburetors with 5 3/16" x 5 5/8" bolt pattern. Performance upgrade for stock to mildly modified V-8 enginesCalibrated for excellent street performance right out of the boxFactory preset electric choke for easy startupsVacuum secondaries for use on wide variety of vehicles. Compensate for all vehicle weights, gearing &...
Availability: In-Stock Item
Item #: 32127 -
This hard to find cast aluminum spacer may be all you need to provide that little bit of extra clearance for calipers, control arms, frame rails, etc. At only 1/8" thick, it does not require longer wheel studs like many thicker spacers you find on the market.
Availability: Ships Direct from Supplier (Except International)
Item #: 32128 -
Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...
Availability: In-Stock Item
Item #: 32132 -
Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.
Availability: In-Stock Item
Item #: 32133 -
Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.
Availability: In-Stock Item
Item #: 30583 -
Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.