All Available Parts - 1973 Ford Mustang

Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair.Replaces Ford part # C8AZ-2B299-A.

Replaces Ford Part # C8AZ-2069-A Sold individually

Replaces Ford Part # 43260-S Sold individually

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...

Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Used in multiple applications front and rear lap belts. Inner and outer, marked with a letter "B" in at least three known fonts. 1-3/4 inches long, 1/2 inch shoulder, Torx 50 tool for installation and removal.

Two per car, identified with the letter "D" in three known fonts. This bolt was used in conjunction with a chrome spacer / washer that is also marked with the letter "D". 1-1/2 inches long, 1/4 inch shoulder, use a Torx 50 for installation and removal.

Used on inner and outer rear seat belt bolts, four per car in 1970 -1971 and used only on the inner rears in 72 - 73 due to the addition of rear retractors. Used in conjunction with two red washer / spacers, marked with three known font styles of the letter "A". 1-5/16 inches long, Torx 50 is the tool for installing and removing.

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Replaces Ford Part # 382626-S Sold individually

Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

Used single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. Sold individually

New single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. AMK part. Sold individually

Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S

This is longer of the two with the + on the bolt head.

part# 372821-S

Ford manual transmission flywheel and automatic transmission flex plate mounting bolts. 6 bolts required, sold individually. Replaces Ford part # 378172-S

Replaces Ford part # 55806-S

part # 56131-S

Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351.

Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually

Reproduction 351W Intake Manifold Bolt for the 1969 - 1973 Mercury Cougar - 1969 - 1973 Ford MustangSold individually 

Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually 

Replaces Ford part # 351089-S Zinc (dark silver) finish Sold individually

Replaces Part # C9OB-3B284. We also have this bolt available in fine thread but only as a used bolt. Four required per car. Sold individually

part # 370608-S. Used in multiple places on mounting brackets.

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

part # 383722-S Pivot bolt for use with the all steel 1970-73 power steering pump mounting bracket. NOS new old stock! Fits most all Ford 302/351 from 1970-73 with the above described bracket.

OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S

part# 384114-S100 Sold individually

Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.

1/2"-13 x 4 1/2" grade 8 flanged bolt with a phosphate and oil finish.  Ford Part # 382486-S.

replaces Ford part # B-12764

Replaces Ford part #375381-S Phosphate & Oil Finish

Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S

Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.

Sold indiviually Phosphate & Oil (gay-black)

Complete engine mounting hardware kit for the 72-73 351C 2-barrel engine. See below for list of included hardware. Click on images to enlarge.

Complete engine mounting hardware kit for the 72-73 351C 4-barrel engine. See below for list of included hardware. Click on images to enlarge.

Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out our video on Radiator and Fan upgrades below:

New valve cover bolts for all Boss 302, 351C-2V, and 351C-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 16.*Note - Excludes 289/302 and 351W engines (see part  number 8316)1/4-20 X 5/8" Hex Head Bolt with Electrolytic Zinc & Wax finishReplaces Ford part number 373071-S.

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford mustangs equipped with disc brakes.

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford Mustangs equipped with drum brakes.

Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang H code 351-2V engines. Cable length 23-3/4 inches long. Uses a green plastic bushing to attach to the throttle pedal. We believe that the MPC is wrong on the length. Our observations are that the 2V cable is longer than the 4V version.Replaces Ford part number D3ZZ-9A758-B.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...

Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang Q code 351-4V engines. Cable length 23 inches long. Identified by the blue plastic bushing on the throttle pedal end of the pedal. We believe that the MPC is wrong on the stated length, the 4V cable is shorter than the 2V version.Replaces Ford part number D3ZZ-9A758-C.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine. Cable length 24 inches long, check your application. There were size differences between the 2V and the 4V engines. Replaces Ford part number D3ZZ-9A758-C. *Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that date, I think it was much earlier, than July 1972. ...

SBVALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1968-1971 Mercury Cougar and 1968-73 Ford Mustang with 289/302/351W engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2OZ-6582-C & D2OZ-6582-D. *Note - This cover will not work on a 351 Cleveland engine.

replaces Ford part # 385161-S Zinc - Dichromate (yellow - rainbow) finish

Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

For 1972-73 Mercury Cougars and Ford Mustangs with the 351W engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Whew boy, say that 5 times fast!Ford part # D2ZA-2981-A. May also have part numbers of D2ZA-2981-A1A, D2ZA-2981-A1B, or D2ZA-2981-A2A.

Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.

Used bolts, and usually new washers. Convertible kit comes with 4 - "A" bolts, 4 "B" bolts, 10 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang convertibles. Coupes or hard tops would include shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us...

384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T.Licensed by FORD

Good quality but not as good as original in that it is too shiny. Fits Coupe or convertible, left or right. Sold individually. Ford emblem sold separate. Replaces Ford part # D1ZZ-6513298-A

Good deal for the guy missing a sill plate on a driver. Sold individually.

Reproduction stainless steel scuff / sill plate. Fits Coupe or convertible, left or right. Sold as a pair. Ford emblem sold separate, find it here. Replaces Ford part # D1ZZ-6513298-A

Door striker replacement bushing.   .90 tall, .69 OD. .49ID. .10 thickness. These plastic bushings were used starting in 1972. We also sell the whole striker assembly. Common striker to many Ford cars after 1971. Apparently Sikorski helicopters too.

Door Striker bolt assembly complete with PVC bushing. 7/16-14 thread. Silver zinc finish. Replaces Ford part #: D2AZ-6522008-A.

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Replaces Ford Part #: D1ZZ-6221813-A

Replaces Ford Part #: D1ZZ-6221812-A

Convenient matched sets save costly locksmith work. Kits includes a pair of door lock cylinders. Comes with two keys. Includes door cylinder gaskets. Replaces Ford Part # : D2AZ-6521984-A

Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits 1970 through 1973's manufactured before 5/17/1973. Replaces Ford Part #: D0AZ-11572-A, D2AZ-11582-B, SW-1114.

These are the screws that secure the door latch mechanism to the door shell. These screws come with the attached crown headed lock washer, just like the originals, so be sure to tighten them down snugly to ensure that the screw head sits flush into the screw holes. Sold individually. Three required per door, six per car.

Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA  ...

Latch rod that links the door latch and the inside door handle, passenger side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521940-A.

Latch rod that links the door latch and the inside door handle, driver side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521941-A.

Inside door handle release mechanism for the driver side on 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the deluxe door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with molded armrests, instead of the smaller detachable armrests on the base interiors. This style was used after 9/15/1971. It...

Inside door handle release mechanism for the passenger side on base model standard 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the base door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with detachable arm rests, instead of the molded arm rests on the door panels, as found on the XR7 and Decor...

Inside door handle release mechanism for the passenger side on 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the deluxe door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with molded armrests, instead of the smaller detachable armrests on the base interiors. This style was used after 9/15/1971. It...

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

Good used drivers side door latch for inside the door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes as shown, we also have latch rods, fasteners, etc in the related items. Replaces Ford Part #: D1ZZ-6221813-A

Good used drivers side door latch for inside the door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes as shown, we also have latch rods, fasteners, etc in the related items. Replaces Ford Part #: D1ZZ-6221813-A

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1970-73. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Sometime after 1973, Ford changed the ignition lock cylinder end. We know it works through 1973, not sure of the change. It must fit the brass lock gear at the bottom of the cylinder hole in the side of the steering column. Refer to your shop manual for removal and installation. Includes two...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

Nice reproduction of the outer door handles for the 1971, 1972 or 1973 Mercury Cougar. Replaces Ford Part #: D1ZZ-6222404-A or D1ZZ-6222405-A.

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

This is the round metal threaded disc that attaches the D0ZZ-6523258-A bushing to the door glass brackets. About 1-3/4" in diameter, two each per door glass on a 1970. 1971-73 Mercury Cougar and Ford Mustang use 3 of these for retaining the door channel bracket. Ford part number 384289-S.Click on images to enlarge. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy...

57084-S Attaching bolt with 7/16" hex head and captured washer. Among other things, it is used to attach the door run, window stops (all 3), both window stabilizers, and the window regulator. Same bolts for manual and power window regulators. Bolt sold individually, there are a good handful in each door. This bolt is used for bolting in the bolt-in glass on 1970, lower "L" bracket for rear quarter windows on 1971-73 Cougar and Mustangs.

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Great reproduction of a rather hard to find part.

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror on the passenger side. This fits any FoMoCo Sport mirror 69 and up, left hand only. Comes with two round pieces of double sided tape. Keep in mind if your lens is bad and it...

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

Reproduction passenger side (right hand) sport mirror lens for the Mercury Cougar or Ford Mustang and Torino.The mounting screw, that holds the mirror assembly in, is not included by default but is an optional addon. Replaces Ford part # C9AZ-17698-B. Dimensions: 4 7/16" x 2 15/16" This version does NOT include the wording "objects in mirror are closer than they appear". We also sell the version with the wording. Do you have questions about installing a passenger side mirror or using...

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a...

Lens with mounting hardware only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Count on the glass being scratched. The value here is in adjustment / mounting hardware. This unit will be guaranteed to keep its adjustment and not be loose like many have become over the years. Keep in mind this item is...

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...