All Available Parts - 1972 Ford Mustang

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

Chromed dipstick tube and dipstick for the 351 Cleveland. Average quality part, made in China. Replaces Ford part # D0ZZ-6750-K.

The oil filter made by the original Ford supplier.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

Please remove your regulator prior to shipping. Be careful of the mechanical energy stored with the spring under tension. Used rear pancake power window motor that is in good original condition for the Mercury Cougar or Ford Mustang. This motor has been professionally tested and has been found to be in good working order. Typically, these motors are service replacement motors that have been replaced sometime in the car's life.Ford part # C9WY-6530304-A.If you are interested in our service that...

NOS (New Old Stock) rear pancake motor for the rear quarter windows of the Mercury Cougar or Ford Mustang. These motors are often ruined because water has leaked down into the quarter panel where it has then seeped into the motor. Once water gets inside the case, the motor's days are numbered. This is because the interior of the case will eventually start to rust and it will seize the motor. This motor is a service replacement part and it would have been the motor your local dealership would...

Used upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, bushing, and contours. Ford part number D1ZZ-7521-B.

Used passenger side (right hand) quarter window regulator for the Mercury Cougar or Ford Mustang equipped with power windows. *NOTE* If your also having some issues with your rear pancake window motor, check out our video below. It will take you through the pancake motor refurbishing process. If we can do it, there is no reason why you can't too! ...

Used on the 1970 Mustang, 1970 - 1971 Cyclone and Torino and 1971 1972 1973 Cougar style steel wheel 14 x 7". Master Parts Catalog description: 15-1/4" O.D., 11" I.D., 2-3/4" wide. This grade A brushed beauty ring will look right at home on a low mile car, no curb rash!!! Ford part number D0ZZ-1210-B Ford superseded this part with part number in 1974 with D4WY-1210-A which looks the same just a little bit deeper at 2 7/8" deep ...

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide. No dings and only the slightest scratches.The part number is D0DZ-1210-A and the engineering number is D0DA-1210-B. Sold individuallyFits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972...

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide. No dings and only the slightest scratches.The part number is D0DZ-1210-A and the engineering number is D0DA-1210-B. Sold individuallyFits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972...

Nice quality reproduction of the upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, and contours. Ford part number D1ZZ-7521-B.

Adjusting rod - Lower clutch rod that fits between the Z-bar and the clutch fork. Replaces Ford Part # C8AZ-7521-B THIS FITS: 1971 1972 1973 MUSTANG 6 CYLINDER 302 351C BOSS 351 1971 MUSTANG 429CJ 429SCJ 1972 1973 1974TORINO351C 351 CJ 1968 1969 1970 1971GALAXIE 6 CYLINDER 302 351 390 429 1968 1969 1970 1971 MERCURY FULL SIZE351 390 429 1971 COUGAR429CJ 429SCJ 1971 1972 1973COUGAR 351C 351CJ 1972 MONTEGO6 AND 8 CYLINDER

D1DZ-6561883-A Spring that keeps tension on the adjusting seat track latch, it keeps it locked. 1971 - 1973 Mercury Cougar and Ford Mustang Bucket Seats. We think that this later spring for the 1972 and up seats was a service replacement part.

Used clutch pedal return spring with two original nylon bushings. Ford Part #: C8OZ-7534-B.

Equalizer bar or "Z" bar for 351 and 429CJ engines with a manual transmission. Used after 4-30-1971. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use. Ford part # D1ZZ-7528-C.*NOTE* Before 4-30-1971, use Ford part # D1ZZ-7528-A.

Bucket seat track set for 1972 Mercury Cougar and Ford Mustang after 12/1/1971 and 1973 cars. Our premium grade used tracks are carefully inspected for damage prior to shipping. Most likely you will have to paint, but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Kit includes brackets D2ZZ-6561704-A and D2ZZ-6561705-A. *NOTE* Not compatible with the power seat option.

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

Single sheave pulley 6-61/64 inches in diameter.Applications:1970 Boss 302 Eliminators without power steering1970 351 engines without power steering1971 - 1973 351 engines without power steering and without A/C.Ford casting number C9OE-8509-E. Ford part number C9OZ-8905-B *Note - this is a very shallow pulley, it is meant to run in the second belt position from the engine. ...

D0OE-6312-C For both Cleveland and Windsor 351 engines. This is also the "with air conditioning" pulley, but with power steering option. Triple sheave 8.00", 7-55/64", 6-9/16" diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0OZ-6A312-B. This is a Service Replacement pulley for D0AE-6312-C. *Excludes 1972 Q code 351 Cobra Jet engines. This means all 1972 351C-4V engines.

D1ZE-6312-C Application - Q code 351 Cobra Jets with air conditioning and power steering. Triple sheave pulley, 6-11/16" and 7-9/16" diameters. Ford Master Part number D1ZZ-6A312-A. *Note - References also list casting number D1ZE-6312-CA as being the same.

D2AE-6312-A Application is for both H and Q code 351 engines without air conditioning and without power steering. Single sheave pulley, 6-3/8 inches in diameter and 4-1/8 inches long. Ford Master Part number D2AZ-6A312-A.

Vacuum tested working hot water valve for any 1969-73 Mercury Cougars or Ford Mustang equipped with factory A/C. This valve stops the flow of warm coolant in the heater hose, when the A/C is on. Has the original cast brass valve and vacuum pod. Used but functional, the reproduction version is very good, but has a black plastic valve, like the service replacement valves from Ford.Replaces Ford part number C9AA-18495-D.

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer.Ford part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-39/64 inches and sometimes mentioned as 1.61". Reference number YA-71.Ford part # C8DE-8546-A, Ford engineering number C2OZ-8546-G.

Fan spacer, measuring 1-7/8 inches or sometimes mentioned as 1.88". Application includes 1970 Mercury Cougar and Ford Mustang with 428CJ engines. Reference number YA-81.Ford part # C8AE-8546-C, Ford engineering # C6OZ-8546-D.

Fan spacer, measuring 2-1/8 inches. Application includes 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Reference number YA-83.Ford part # C8SE-8546-B, Ford engineering # C8SZ-8546-D.

C9AF-10A352-A or -B Alternator pulley for use with only one drive belt. Just under 2-3/4" inches in diameter. This later version would have a casting number of C9AF-10A352-A or possibly C9AF-10A352-B stamped on it. Ford master part number is C5AZ-10344-K like the above pulley.

These are used hose clamps that have a tab and fold over on them selves. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available do have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, or straps bundling the hoses on most cars. These clamps should fit a variety of different Ford and Mercury products, not just Mustang and Cougar....

Decent reproduction of the air conditioning sight glass hose for the Mercury Cougar and Ford Mustang. Hose texture is not the same and the sight glass itself is different, but length and fittings are correct. If your sight glass hose is not original or you do not have the 2 piece quick disconnect, you may need to purchase the complete sight glass hose kit. For 100% correct hose, please see our good used sight glass hoses. Includes Sight Glass Hose (Ford Part # D1ZA-19837-A or...

This hose connects the sight glass hose to the air conditioning dryer. Includes the sight glass to dryer hose. Ford Part #: D1ZA-19835-A.This hose is compatible with both 134a and R12 refrigerants.

Reproduction A/C discharge service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 3/4" fitting. This valve accepts the R134A connection, not the R12.

Reproduction A/C suction service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 7/8" hose fitting. Replaces part # D0AZ-19752-A or D0AA-19752-A.

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

Rod used for locking the 3 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 12 inches long and was originally marked with a purple paint mark. The 3 speed manual transmission, could be ordered only on "H" code 351-2V engines in 1971 and 1972. Transmission code "1" on your door data tag. *Trivia - 1972...

Rod used for locking the 4 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 13 inches long and was originally marked with a green paint mark.The 4 speed manual transmission, could not be ordered on the 351-2V engines. Only 351-4V's and 429CJ's in 1971, and 351CJ's (Q code) in both 1972 and...

Windshield defroster nozzle for Mercury Cougar and Ford Mustang without A/C. This is a "A" grade unit and will have 1 or 2 scuffs in the plastic, or small crack in the flex hose. You will need to staple the flex part onto your heater unit. Very fragile part, almost always going to have Grade B, seldom will we have a Grade A used.Ford part # D1ZA-18A565-AD

Used vacuum switching manifold and electrical micro switch assembly from a mid to late 1972 through 1973 Mercury Cougar and Ford Mustang. This is the plastic version with riveted micro switch. We test the micro switches prior to shipping. Please check your A/C controller to verify that you have and need the plastic version of this switch. We also have the all metal version with separate micro switch which can be interchanged, but you would need a micro switch.Ford number D2ZA-19B919-A or...

New Old Stock Glove box or glove compartment light with switch. Fits 1971-73 Mercury Cougar and Ford Mustang. Used switch and wiring assembly, tested and working. Ford part number D1WY-14413-A. Fits 71 CougarFits 72 CougarFits 73 CougarFits 71 MustangFits 72 MustangFits 73 Mustang ...

Replacement cork pan gasket for all 1965-73 C4 Ford transmissions. 

Replacement rubber material pan gasket for all 1965-73 C4 Ford transmissions. 

1972 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Rebuilt with the inclusion of a fixed lower shaft which eliminates the need for the hard to find (and expensive) tilt rag joint. No change to the installation, or function, and will be in stock more often than our full priced 1972 tilt column.Rebuilt with the inclusion of a fixed lower shaft which eliminates the need for the hard to find (and expensive) tilt rag joint. No change to the installation, or...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.

Ignition housing / cover for the fixed steering column on 71 - 73 Cougars and Mustangs. Technically called a "Flange", the ignition cylinder sits inside this cover.This item will need to be re-painted to match your column.Ford Part number D0AA-3511-CW

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Steering column locking gear. For all 1970-73 Ford and Mercury steering columns. Made of brass, has 8 teeth and is 7/16 inches thick. Fits fixed and tilt steering columns. Ford part number D0AZ-3E717-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Replaces Ford part #C7AZ-6892. For round hole with two notches, aluminum or steel valve covers.

Complete, solid tilt column with no missing or cracked parts. Easy to install and is as comfortable of an upgrade as you maybe imagining it to be. Although they may look much alike, each year 1970-73 is unique. In my opinion this upgrade enhances your cars value in direct proportion to its cost and will not cost you points in judged shows as it was a commonly installed dealer option. Often times we are unable to stock 1971-73 tilt columns due to not having tilt rag joints. We now offer a...

Perfect set of four radio knobs for your Mercury Cougar or Ford Mustang. Very hard to find with flawless chrome as most are peeling bad enough to cut you if you are not being cautious. Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob. D1ZZ-18830-A for the inner (balance / tone) knob, Ford casting # D1ZA-18A932-AA on the inner (balance / tone) knob.*TRIVIA* Did you know that Ford called the outer (balance / tone)...

Premium grade used outer (tuner / volume) knob with no missing chrome or cracks. Two required per car, sold individually. We also have knobs with peeling chrome, we are happy to throw a damaged knob in for free with your order, just ask! We also have reproduction sets available.Ford part # D1ZZ-18817-A, and Ford casting # D1ZA-18822-AA.

Reproduction insulation located behind the kick panels on the 71 - 73 Cougar or mustang. Correct cut allows access to the door hinge bolts.

D1AZ-6788-A Metal tab that bolts to the intake manifold and has a hole for the round hose retaining ring (part number D2AZ-14A163-K). 1972-1973 all 351 engines, *Restoration Tip - These were painted Ford engine blue when the engines were painted, so paint it Dark Ford engine blue.

D2AZ-14A163-K Black plastic ring that barely fits over the PCV hose. Ring end locks into the D1AZ-6788-A hose bracket. Fits all 1972-73 351 engines, both 2V and 4V engines. This retaining ring came from Ford's electrical section.

Used on front doors of cars with factory door speakers. Ford casting number D2AB-7630323-AA. Very hard to find with plastic knob still intact.

Sold as a pair, nothing beats original Ford for fit and finish! We are currently out of NOS handles, do you have some for sale?

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and their 30 watt little brother are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Features Kenwood 60 watt peak power speakers, nice upgrade over the low wattage originals. Sold as a pair.   These pictures show what every 69-70 door panel looks like on the backside.  They are all perforated from from the...

D1OZ-6A664-B Original used hose that connects the valve cover mounted PCV valve and the carburetor spacer plate on 1971 through 1972 Mercury Cougar and Ford Mustang 351C or Cleveland engines only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes all 1969-71 351W or Windsor engines, 1970 351C or Cleveland, and 1973 351C engines. *Note - These molded and contoured hoses were...

Used on front doors of cars produced after 10-1-71 with no factory door speakers. Ford part number D2AZ-7630322-A, casting number D3AB-6523342-AA. Very hard to find with plastic knob still intact.

Heavy duty door hinge rebuild kit for the 1971 - 1973 Cougar or Mustang. Included in the kit are:2 Machined hinge pins2 Machined steel tubes4 Oil impregnated bushings2 Stainless steel washers2 Zerk FittingsEach kit is enough to do one side and includes one big and one small pin / tube set.

This plastic fastener is used to keep your mirror cable from interfering with the movement of your door glass. It is located at the front of the door near the top.

Round plastic window stop that attaches to the front and rear door window glass on all 1971-73 Mercury Cougar and Ford Mustangs. Two per door

Used driver side (left hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. It will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # D1ZZ-6521411-C.  *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom...

Used passenger side (right hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # D1ZZ-6521410-C.  *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in...

Used driver side (left hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # D1ZZ-6521411-C....

Used driver side (left hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part #...

Used passenger side (right hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part...

Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.

This pigtail fits left or right rear quarter power window switches and motor. Taken from an original used harness that had a Ford part number of D1ZB-14644-AB

Original stereo radio pigtail and plug. From a 1972-73 Mercury Cougar or Ford Mustang stereo radio. Has correct plug, wire colors and makings for the plug that connects to the factory speaker harness.  *Note This is the speaker radio lead, from the radio.

Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.

Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included. Ford part number C3AZ-4851-L.

D0OZ-4204-9A300 1968-1973 9 Inch Third Member - UsedAlso called a pumpkin, 3.25:1 open ratio. These 3rd members will have the fill plug and 28 splined axles.Check your door tag under "Axle".

Restored passenger side (right hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Passenger and driver sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip....

Restored driver side (left hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Right and left sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weather strip. Shipping...

Used, passenger side, front lower, aluminum channel section, for installing the roof side or upper door and quarter window weatherstripping. Right and left sides are contoured differently, for the 1971-73 Mercury Cougar and Ford Mustang coupe and convertibles. These channels also have pre-drilled holes for installation, often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip....

Used rubber bumper for the tilt column. 70 - 73 tilt columns require 3 bumpers, one on the lower and two on the upper knuckles. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth.  Replaces Ford part # D0AZ-3B661-A. *NOTE*...

Used mounting bracket. This is the mounting plate for the end links on the factory rear sway bar. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates are mounted with the shock mounting plates on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. Replaces Ford part number D0ZZ-5A775-A.NOTE: These are only a few of these in stock, and they will have moderate pitting.Mustang...

Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. All 351C engines, 351-2V and 351-4V. Fits any 1972-73 Mercury Cougar or Ford Mustang with original H or Q code 351C engines. The earlier bracket found on the 1971-72 cars will also work and is stamped slightly differently.Replaces Ford part number D2AZ-9728-A.

This extension holds the inner spring tube in place on the 70 - 73 tilt column. Fragile piece, should take great care when tapping on this pot metal piece. Limited supply. Ford casting number: D0ZA-3790-*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used lower steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column and can be the issue when you have a sloppy feeling tilt column. The hard steel pin will often waller out the soft cast metal and cause play in the column. Ford part # D1AZ-3D651-A, casting number D1AA-3D651-AA or D0AA-3508-F. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Good used upper collar for the tilt column on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded integral steering box unique to the later Cougars. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

Good used actuating rod for the ignition switch on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang. 8-1/8 inches on rod center long.

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found on cars with 427-4V, 428CJ, 429CJ, Boss 302, Boss 351, or Boss 429. These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available:There are other versions of the Nodular iron third members. Non-"N", lazy "N" like this one, and square "N". See related items.  Please have your desired date in mind when calling or place it in...

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found in 1973 and newer Ford products, mostly F100 and Bronco.  These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available: There are other versions of the Nodular iron third members. Non-"N", lazy "N", and square "N" this version. See related items.  Please have your desired date in mind when calling or place it in...

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...